How do you replace the door latch,Door Handle and Door Lock Cylinder on Chrysler Town & Country?

To replace the front door latch, shut the window fully and then, pop off the front door trim panel, lift up the plastic water shield to get to the inner door hardware. If reinforced with power door locks, the wire connector has to be disconnected from the power door lock motor. Remove the clips which fasten the linkage to the door latch and then the linkages then the screws mounting the door latch to the door end frame then take out the latch. Removal is the exact opposite of installation though one is advised to use new screws if the latch has been removed. When completed with the installation of the door latch by using new screws, slide in the linkage into the latch and engage the clips and if their is electrical connector reconnect it. For the outside handle, the initial steps as with the inside handle to reach the inside of the door release mechanism, and disconnect switch connector in case your car came with Vehicle Theft Security System, and release the push in fasteners. Take out the handle to the outer panel by taking out the latch and lock linkages from the handle. In the outside handle for the lock cylinder you will need to pop of a clip then pull it out then you will need to install the new lock cylinder retaining clip and position the link arm before pushing the lock cylinder back in. For the sliding door latch/lock control, it is necessary to remove the trim panel of the sliding door, disconnect the external cable given in the figure, and also remove the foam insulation block given in the figure. Remove the inside latch handle and free the clip where the inside door handle bell crank link was previously fixed, also use bolts to take off the latch/lock control from the sliding door. For the outside handle of the sliding door, the procedure is almost similar to the internal handle to gain access to the handle. For the liftgate latch, the trim panel and watershield must be pulled off, the connection of the outside lock cylinder link and wire connector have to be disconnected and the screws of the latch have to be loosened. The outside handle for the liftgate includes; removal of the trim panel, followed by the electrical connectors and finally the removal of mounting screws. Last but not least, to take out the liftgate lock cylinder, press the clip to release latch link, if there was an electrical connector, then disconnect it, then turn counterclockwise the plastic nut on the lock cylinder and remove it. To uninstall all the components the process is the exact opposite of installation.

Genuine Chrysler Town & Country Door Handle

Inside Door Handle

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

646 Door Handles found

View related parts
Chrysler Town & Country Handle-Door Interior
Part Number: 68066553AA
$69.36 MSRP: $203.00
You Save: $133.64 (66%)
ADD TO CART
Product Specifications
- Other Name: Handle Door Interior
- Replaced by: 68066553AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2013 Chrysler Town & Country | Gold, Limited, LX, S, Touring, Touring L | 6 Cyl 3.6L
View related parts
Chrysler Town & Country Handle-Exterior Door
Part Number: 1NA50GW7AD
$109.40 MSRP: $164.00
You Save: $54.60 (34%)
ADD TO CART
Product Specifications
- Other Name: Handle Exterior Door; Handle, Outside
- Replaced by: 1NA50TZZAD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2013-2016 Chrysler Town & Country | Limited, Limited Platinum, LX, S, Touring, Touring L, Touring-L | 6 Cyl 3.6L
View related parts
Chrysler Town & Country Handle-Exterior Door
Part Number: 4589716AE
$95.89 MSRP: $144.00
You Save: $48.11 (34%)
ADD TO CART
Product Specifications
- Other Name: Handle Exterior Door; Outside Handle
- Position: Passenger Side
- Replaces: 4589716AB, 4589716AC, 4589716AD, 4589716AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2010-2016 Chrysler Town & Country | Gold, LX, Limited, Limited Platinum, S, Touring, Touring L, Touring Plus, Touring-L | 6 Cyl 3.3L, 6 Cyl 3.6L, 6 Cyl 3.8L, 6 Cyl 4.0L
View related parts
Chrysler Town & Country Handle-Door Interior
Part Number: 68066553AB
$135.23 MSRP: $203.00
You Save: $67.77 (34%)
ADD TO CART
Product Specifications
- Other Name: Handle Door Interior; Inside Handle
- Position: Driver Side
- Replaces: 68066553AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2016 Chrysler Town & Country | Gold, LX, Limited, Limited Platinum, S, Touring, Touring L, Touring-L | 6 Cyl 3.6L
View related parts
Chrysler Town & Country Handle-Exterior Door
Part Number: 1NA54WS2AA
$81.13 MSRP: $169.00
You Save: $87.87 (52%)
ADD TO CART
Product Specifications
- Other Name: Handle Exterior Door
- Replaced by: 1NA54WS2AF
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009-2010 Chrysler Town & Country | Limited, LX, Touring, Touring Plus | 6 Cyl 3.3L, 6 Cyl 3.6L, 6 Cyl 3.8L, 6 Cyl 4.0L
View related parts
Chrysler Town & Country Handle-Door Interior
Part Number: 68066552AA
$100.39 MSRP: $208.00
You Save: $107.61 (52%)
ADD TO CART
Product Specifications
- Other Name: Handle Door Interior
- Replaced by: 68066552AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2013 Chrysler Town & Country | Gold, Limited, LX, S, Touring, Touring L | 6 Cyl 3.6L
View related parts
Chrysler Town & Country Handle-Exterior Door
Part Number: 4589716AA
$68.92 MSRP: $144.00
You Save: $75.08 (53%)
ADD TO CART
Product Specifications
- Other Name: Handle Exterior Door
- Replaced by: 4589716AE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2010 Chrysler Town & Country | Limited, LX, Touring, Touring Plus | 6 Cyl 3.3L, 6 Cyl 3.6L, 6 Cyl 3.8L, 6 Cyl 4.0L
View related parts
Chrysler Town & Country Handle-Exterior Door
Part Number: 4589716AC
$68.92 MSRP: $144.00
You Save: $75.08 (53%)
ADD TO CART
Product Specifications
- Other Name: Handle Exterior Door
- Replaced by: 4589716AE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2013 Chrysler Town & Country | Gold, Limited, LX, S, Touring, Touring L | 6 Cyl 3.6L
View related parts
Chrysler Town & Country Handle-Exterior Door
Part Number: 4589716AD
$68.92 MSRP: $144.00
You Save: $75.08 (53%)
ADD TO CART
Product Specifications
- Other Name: Handle Exterior Door
- Replaced by: 4589716AE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2014 Chrysler Town & Country | Limited, S, Touring, Touring L | 6 Cyl 3.6L
View related parts
Chrysler Town & Country Handle-Exterior Door
Part Number: 1NA50KFSAD
$109.40 MSRP: $164.00
You Save: $54.60 (34%)
ADD TO CART
Product Specifications
- Other Name: Handle Exterior Door
- Replaced by: 1NA50TZZAD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2013-2016 Chrysler Town & Country | Limited, Limited Platinum, LX, S, Touring, Touring L, Touring-L | 6 Cyl 3.6L
View related parts
Chrysler Town & Country Handle-Sliding Door Exterior
Part Number: 1NA50ARHAA
$109.40 MSRP: $164.00
You Save: $54.60 (34%)
ADD TO CART
Product Specifications
- Other Name: Handle Sliding Door Exterior
- Replaced by: 1NA50TZZAD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2010 Chrysler Town & Country | Limited, LX, Touring, Touring Plus | 6 Cyl 3.3L, 6 Cyl 3.6L, 6 Cyl 3.8L, 6 Cyl 4.0L
View related parts
Chrysler Town & Country Handle-Sliding Door Exterior
Part Number: 1NA50AXRAA
$109.40 MSRP: $164.00
You Save: $54.60 (34%)
ADD TO CART
Product Specifications
- Other Name: Handle Sliding Door Exterior
- Replaced by: 1NA50TZZAD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2010 Chrysler Town & Country | Limited, LX, Touring, Touring Plus | 6 Cyl 3.3L, 6 Cyl 3.6L, 6 Cyl 3.8L, 6 Cyl 4.0L
View related parts
Chrysler Town & Country Handle-Exterior Door
Part Number: 1NA50AXRAC
$109.40 MSRP: $164.00
You Save: $54.60 (34%)
ADD TO CART
Product Specifications
- Other Name: Handle Sliding Door Exterior
- Replaced by: 1NA50TZZAD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2012 Chrysler Town & Country | Gold, Limited, LX, Touring, Touring L | 6 Cyl 3.6L
View related parts
Chrysler Town & Country Handle-Exterior Door
Part Number: 1NA50AXRAD
$109.40 MSRP: $164.00
You Save: $54.60 (34%)
ADD TO CART
Product Specifications
- Other Name: Handle Exterior Door; Handle, Outside
- Replaced by: 1NA50TZZAD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2013-2016 Chrysler Town & Country | Limited, Limited Platinum, LX, S, Touring, Touring L, Touring-L | 6 Cyl 3.6L
View related parts
Chrysler Town & Country Handle-Exterior Door
Part Number: 1NA50DX8AC
$109.40 MSRP: $164.00
You Save: $54.60 (34%)
ADD TO CART
Product Specifications
- Other Name: Handle Sliding Door Exterior
- Replaced by: 1NA50TZZAD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2012 Chrysler Town & Country | Limited, Touring, Touring L | 6 Cyl 3.6L
View related parts
Chrysler Town & Country Handle-Sliding Door Exterior
Part Number: 1NA50EBGAA
$124.27 MSRP: $164.00
You Save: $39.73 (25%)
ADD TO CART
Product Specifications
- Other Name: Handle Sliding Door Exterior
- Replaced by: 1NA50TZZAD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2010 Chrysler Town & Country | Limited, LX, Touring, Touring Plus | 6 Cyl 3.3L, 6 Cyl 3.6L, 6 Cyl 3.8L, 6 Cyl 4.0L
View related parts
Chrysler Town & Country Handle-Sliding Door Exterior
Part Number: 1NA50GUVAA
$109.40 MSRP: $164.00
You Save: $54.60 (34%)
ADD TO CART
Product Specifications
- Other Name: Handle Sliding Door Exterior
- Replaced by: 1NA50TZZAD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2010 Chrysler Town & Country | Limited, LX, Touring, Touring Plus | 6 Cyl 3.3L, 6 Cyl 3.6L, 6 Cyl 3.8L, 6 Cyl 4.0L
View related parts
Chrysler Town & Country Handle-Exterior Door
Part Number: 1NA50GUVAC
$109.40 MSRP: $164.00
You Save: $54.60 (34%)
ADD TO CART
Product Specifications
- Other Name: Handle Sliding Door Exterior
- Replaced by: 1NA50TZZAD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011 Chrysler Town & Country | Gold, Limited, LX, Touring, Touring L | 6 Cyl 3.6L
View related parts
Chrysler Town & Country Handle-Exterior Door
Part Number: 1NA50HAVAC
$109.40 MSRP: $164.00
You Save: $54.60 (34%)
ADD TO CART
Product Specifications
- Other Name: Handle Sliding Door Exterior
- Replaced by: 1NA50TZZAD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2013 Chrysler Town & Country | Gold, Limited, LX, S, Touring, Touring L | 6 Cyl 3.6L
View related parts
Chrysler Town & Country Handle-Sliding Door Exterior
Part Number: 1NA50HBVAA
$109.40 MSRP: $164.00
You Save: $54.60 (34%)
ADD TO CART
Product Specifications
- Other Name: Handle Sliding Door Exterior
- Replaced by: 1NA50TZZAD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2010 Chrysler Town & Country | Limited, LX, Touring, Touring Plus | 6 Cyl 3.3L, 6 Cyl 3.6L, 6 Cyl 3.8L, 6 Cyl 4.0L

| Page 1 of 33 |Next >

1-20 of 646 Results

Chrysler Town & Country Door Handle

The Chrysler Town & Country cars exterior door handle as an important part acts so as to facilitate the access of the car through opening of the doors. Made out of hard wearing plastic or metal the handle is linked to a metal rod and when pulled will lock the door. This mechanism makes it possible to ensure service for years, despite frequent usage of the equipment. Many years of manufacturing the Chrysler Town & Country have seen the use of different styles of Exterior Door Handle that are uniquely designed to fit this car model and you do not need a lot of effort or time in installing them. Pertaining to the general mechanics, dynamics, or structure, the only differences that are likely to be seen are in the visual and functional parts of the materials, in conjunction with the differing or updated vehicle models. In any case, the Exterior Door Handle is designed to be durable for extreme weather condition and frequent touches hence adding on the value and pleasure of owning a Chrysler Town & Country.

Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Chrysler Town & Country Door Handle at great affordable prices. Moreover, all genuine Chrysler Town & Country Door Handle come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.

Chrysler Town & Country Door Handle Parts Questions & Experts Answers

Handle-Sliding Door Exterior
4894510AA
Q: How do you replace the door latch,Door Handle and Door Lock Cylinder on Chrysler Town & Country?
A: To replace the front door latch, shut the window fully and then, pop off the front door trim panel, lift up the plastic water shield to get to the inner door hardware. If reinforced with power door locks, the wire connector has to be disconnected from the power door lock motor. Remove the clips which fasten the linkage to the door latch and then the linkages then the screws mounting the door latch to the door end frame then take out the latch. Removal is the exact opposite of installation though one is advised to use new screws if the latch has been removed. When completed with the installation of the door latch by using new screws, slide in the linkage into the latch and engage the clips and if their is electrical connector reconnect it. For the outside handle, the initial steps as with the inside handle to reach the inside of the door release mechanism, and disconnect switch connector in case your car came with Vehicle Theft Security System, and release the push in fasteners. Take out the handle to the outer panel by taking out the latch and lock linkages from the handle. In the outside handle for the lock cylinder you will need to pop of a clip then pull it out then you will need to install the new lock cylinder retaining clip and position the link arm before pushing the lock cylinder back in. For the sliding door latch/lock control, it is necessary to remove the trim panel of the sliding door, disconnect the external cable given in the figure, and also remove the foam insulation block given in the figure. Remove the inside latch handle and free the clip where the inside door handle bell crank link was previously fixed, also use bolts to take off the latch/lock control from the sliding door. For the outside handle of the sliding door, the procedure is almost similar to the internal handle to gain access to the handle. For the liftgate latch, the trim panel and watershield must be pulled off, the connection of the outside lock cylinder link and wire connector have to be disconnected and the screws of the latch have to be loosened. The outside handle for the liftgate includes; removal of the trim panel, followed by the electrical connectors and finally the removal of mounting screws. Last but not least, to take out the liftgate lock cylinder, press the clip to release latch link, if there was an electrical connector, then disconnect it, then turn counterclockwise the plastic nut on the lock cylinder and remove it. To uninstall all the components the process is the exact opposite of installation.