How to replace Camshaft Seal on Dodge Caravan?

Do not rotate the camshaft(s) or crankshaft when the timing belt is removed or damage to the engine may occur. Begin by removing the timing belt. Rotate the crankshaft counterclockwise until the crankshaft sprocket is three notches BTDC to prevent engine damage if the camshaft sprocket rotates during sprocket bolt removal. Hold the camshaft sprocket and remove the camshaft sprocket bolt; using a strap-type pulley holder tool is recommended for this task. If unavailable, two large screwdrivers can be used to pry the sprocket off the camshaft, or the valve cover can be removed to access the camshaft wrenching flats. Next, remove the idler pulley and the bolts holding the rear cover to the engine block and cylinder head, then take off the rear cover. Pry out the camshaft oil seal carefully to avoid scratching the bore or damaging the camshaft, as damage will cause the new seal to leak. Clean the bore and coat the outer edge of the new seal with engine oil or multi-purpose grease, lubricating the seal lip. Use a socket with an outside diameter slightly smaller than the seal and a hammer to gently tap the new seal into place with the spring side facing inward, ensuring it is flush with the face of the cylinder head. If a socket isn't available, a short section of pipe can be used instead. If space is limited, fabricate a seal installation tool from a piece of pipe, a bolt, and a large washer to press the seal into place. Afterward, install the rear timing belt cover and idler pulley. Install the camshaft sprocket, ensuring the pin in the camshaft aligns with the hole in the sprocket, then hold the camshaft sprocket and tighten the sprocket bolt to the specified torque. Finally, reinstall the timing belt and run the engine to check for oil leaks at the camshaft seal.

Genuine Dodge Caravan Camshaft Seal

Cam Seal

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

9 Camshaft Seals found

View related parts
Dodge Caravan Seal-CAMSHAFT
Part Number: 4777086
$10.39 MSRP: $15.40
You Save: $5.01 (33%)
ADD TO CART
Product Specifications
- Other Name: Seal Camshaft; Camshaft Seal, Front Seal, Oil Seal
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1996-2007 Dodge Caravan | Base, C/V, EC, LE, SE | 4 Cyl 2.4L
View related parts
Dodge Caravan Seal-CAMSHAFT Sensor
Part Number: 4884111AA
$7.47 MSRP: $11.90
You Save: $4.43 (38%)
ADD TO CART
Product Specifications
- Other Name: Seal Camshaft Sensor; Camshaft Sensor Seal, Rear Seal
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2000-2007 Dodge Caravan | Base, C/V, EC, SE | 4 Cyl 2.4L
View related parts
Dodge Caravan Seal-CAMSHAFT Front Oil
Part Number: 4105395
$9.30 MSRP: $11.84
You Save: $2.54 (22%)
ADD TO CART
Product Specifications
- Other Name: Seal, Intermediate Shaft Oil
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1984-1995 Dodge Caravan | Base, C/V (Long Wheel Base VAN) FWD, C/V (Short Wheel Base VAN) FWD, LE FWD, SE FWD | 4 Cyl 2.2L, 4 Cyl 2.5L
View related parts
Dodge Caravan Seal-Cylinder Head CAMSHAFT End
Part Number: MD180183
$13.49 MSRP: $17.20
You Save: $3.71 (22%)
ADD TO CART
Product Specifications
- Other Name: Plug, Cam End; Camshaft Seal, Rear Cam Plug, Rear Seal
- Replaces: MD090761
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1987-2000 Dodge Caravan | Base, C/V (Long Wheel Base VAN) FWD, C/V (Short Wheel Base VAN) FWD, LE, LE FWD, SE, SE FWD | 6 Cyl 3.0L
View related parts
Dodge Caravan Seal
Part Number: 4105396
$7.07 MSRP: $9.00
You Save: $1.93 (22%)
ADD TO CART
Product Specifications
- Other Name: Seal, Camshaft Front; Cylinder Head, Rear Cam Plug
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1984-1987 Dodge Caravan | 4 Cyl 2.2L
View related parts
Dodge Caravan Camshaft Seal
Part Number: MD153103
$5.31 MSRP: $8.50
You Save: $3.19 (38%)
ADD TO CART
Product Specifications
- Other Name: Camshaft-Camshaft
- Replaced by: MD372536
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1994-1999 Dodge Caravan | Base, C/V (Short Wheel Base VAN) FWD, LE, LE FWD, SE, SE FWD | 6 Cyl 3.0L
View related parts
Dodge Caravan Seal CAMSHAFT Oil
Part Number: MD024529
Product Specifications
- Other Name: Seal, Camshaft
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1984-1987 Dodge Caravan | 4 Cyl 2.6L
View related parts
Dodge Caravan Seal Camshaft
Part Number: MD133317
Product Specifications
- Other Name: Oil Seal, Stamped "Nok-AH2057N"
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2000 Dodge Caravan | Base, SE | 6 Cyl 3.0L
- 1992-1993 Dodge Caravan | Base, C/V (Long Wheel Base VAN) FWD, C/V (Short Wheel Base VAN) FWD, LE FWD, SE FWD | 6 Cyl 3.0L
View related parts
Dodge Caravan Seal-CAMSHAFT Rear Oil
Part Number: 4105397
Product Specifications
- Other Name: Seal, Camshaft Front; Rear Cam Plug
- Position: Rear
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1984-1987 Dodge Caravan | 4 Cyl 2.2L

Dodge Caravan Camshaft Seal

In Dodge Caravan used vehicles, the Camshaft Seal plays an important function of having to keep out dirt, oil, and other interferences from getting into the camshaft area which is the exit aperture of the cylinder head. This seal is very critical because it ensures that oil gets to the camshaft to enable smooth running of the engine without interferences. It is most probable that many Dodge Caravan models utilize different Camshaft Seal types or styles throughout the years, however, variations are unclear. The primary function remains consistent across these types: to protect the components of the engine not to come in contact with substances that are destructive while at the same time provide lubrication. The Camshaft Seal is therefore crucial and has great influence of the whole rolling Model of the Dodge Caravan especially with regard to the engine.

Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Dodge Caravan Camshaft Seal at great affordable prices. Moreover, all genuine Dodge Caravan Camshaft Seal come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.

Dodge Caravan Camshaft Seal Parts Questions & Experts Answers

Seal-CAMSHAFT
4777086
Q: How to replace Camshaft Seal on Dodge Caravan?
A: Do not rotate the Camshaft(s) or crankshaft when the Timing Belt is removed or damage to the engine may occur. Begin by removing the timing belt. Rotate the crankshaft counterclockwise until the crankshaft sprocket is three notches BTDC to prevent engine damage if the camshaft sprocket rotates during sprocket bolt removal. Hold the camshaft sprocket and remove the camshaft sprocket bolt; using a strap-type pulley holder tool is recommended for this task. If unavailable, two large screwdrivers can be used to pry the sprocket off the camshaft, or the valve cover can be removed to access the camshaft wrenching flats. Next, remove the idler pulley and the bolts holding the rear cover to the engine block and Cylinder Head, then take off the rear cover. Pry out the camshaft oil seal carefully to avoid scratching the bore or damaging the camshaft, as damage will cause the new seal to leak. Clean the bore and coat the outer edge of the new seal with engine oil or multi-purpose grease, lubricating the seal lip. Use a socket with an outside diameter slightly smaller than the seal and a hammer to gently tap the new seal into place with the spring side facing inward, ensuring it is flush with the face of the cylinder head. If a socket isn't available, a short section of pipe can be used instead. If space is limited, fabricate a seal installation tool from a piece of pipe, a bolt, and a large washer to press the seal into place. Afterward, install the rear timing belt cover and idler pulley. Install the camshaft sprocket, ensuring the pin in the camshaft aligns with the hole in the sprocket, then hold the camshaft sprocket and tighten the sprocket bolt to the specified torque. Finally, reinstall the timing belt and run the engine to check for oil leaks at the camshaft seal.