How to replace a drive axle boot and Axle Shaft on Dodge Charger?

If a Axle Shaft boot has failed, the entire shaft assembly must be replaced as boots are not serviceable separately. To remove, start by removing the wheel cover or hub cap and break the Axle Shaft/hub nut loose with a socket and large breaker bar. Block the front wheels to prevent the vehicle from rolling. Loosen the wheel lug nuts, raise the rear of the vehicle, and support it securely on jack stands. Remove the wheel. Remove the Axle Shaft/hub nut and discard it. Drain the gear lubricant from the differential. Disconnect the driveshaft from the differential and remove the rear exhaust pipe and muffler. Pry the inner CV joint out of the differential just far enough to release the snap-ring. The Axle Shaft can't be removed from the differential until the differential has been lowered. Support the differential with a floor jack. Remove the mounting fasteners securing the differential to the crossmember and differential mount. Carefully lower the differential enough to separate the Axle Shaft(s) from the differential. Pull the Axle Shaft out of the hub flange. If it sticks, tap it out with a soft-faced hammer. Installation is the reverse of removal, noting the following points: Remove the rubber isolation washer from the outer CV joint stub shaft and inspect it. Replace it if necessary. Tighten the differential mounting bolts to the torque. Install a new Axle Shaft/hub nut. Tighten the hub nut securely, but don't try to tighten it to the actual torque specification until you've lowered the vehicle to the ground. Fill the differential with the type and amount of lubricant specified. Install the wheels and lower the vehicle to the ground. Tighten the wheel lug nuts to the torque. Tighten the Axle Shaft/hub nut to the torque. Install the wheel cover or hub cap.

Genuine Dodge Charger Axle Shaft

Car Axle Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

75 Axle Shafts found

View related parts
Dodge Charger Axle Shaft-Cv Joint Half Shaft Left
Part Number: 4578601AA
$432.07 MSRP: $664.00
You Save: $231.93 (35%)
ADD TO CART
Product Specifications
- Other Name: Shaft-Axle Half; Axle Assembly, Drive Axle
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2023 Dodge Charger | Base AWD, GT AWD, Police AWD, R/T AWD, Rallye AWD, SE AWD, SXT AWD, V6 AWD | 6 Cyl 3.5L, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.6L, 8 Cyl 5.7 L GAS, 8 Cyl 5.7L, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Charger Axle Half Shaft
Part Number: 52123962AD
$504.09 MSRP: $772.00
You Save: $267.91 (35%)
ADD TO CART
Product Specifications
- Other Name: Shaft-Axle Half; Axle Assembly
- Replaces: 52123962AC, 52123962AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2015-2023 Dodge Charger | GT RWD, Police RWD, R/T RWD, SE RWD, SXT RWD | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.6L, 8 Cyl 5.7 L GAS, 8 Cyl 5.7L, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Charger Rear-Axle Assembly Or Cv Shaft
Part Number: 4578732AE
$522.64 MSRP: $797.00
You Save: $274.36 (35%)
ADD TO CART
Product Specifications
- Other Name: Shaft-Axle Half; Axle Assembly
- Replaces: 4578732AC, 4578732AD, 4578732AB, 68194754AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2012-2014 Dodge Charger | Police RWD, SRT RWD, SRT Superbee RWD, SRT8 RWD, SRT8 Superbee RWD | 8 Cyl 6.4L
- 2009-2010 Dodge Charger | Base RWD, R/T RWD, SRT8 RWD | 8 Cyl 6.1L
View related parts
Dodge Charger Rear Left Driver Axle Shaft Assembly
Part Number: 53010749AA
$501.55 MSRP: $762.00
You Save: $260.45 (35%)
ADD TO CART
Product Specifications
- Other Name: Shaft-Axle Half; Axle Assembly
- Position: Rear Driver Side
- Replaces: 53010671AB, 53010671AC, 53010671AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2020-2023 Dodge Charger | Police RWD, SRT Hellcat Widebody RWD, Scat Pack RWD | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS, 8 Cyl 6.4L
- 2015-2018 Dodge Charger | Police RWD, R/T 392 RWD, SRT 392 RWD, SRT Hellcat RWD, SRT RWD, Scat Pack RWD | 8 Cyl 6.2L, 8 Cyl 6.4L
View related parts
Dodge Charger Axle Shaft Assembly Driveline And Axles
Part Number: 4578600AA
$436.60 MSRP: $664.00
You Save: $227.40 (35%)
ADD TO CART
Product Specifications
- Other Name: Shaft-Axle Half
- Replaced by: 4578600AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2017 Dodge Charger | Base AWD, Police AWD, R/T AWD, Rallye AWD, SE AWD, SXT AWD, V6 AWD | 6 Cyl 3.5L, 6 Cyl 3.6L, 8 Cyl 5.7L
View related parts
Dodge Charger Axle Half Shaft
Part Number: 68258859AB
$549.95 MSRP: $835.00
You Save: $285.05 (35%)
ADD TO CART
Product Specifications
- Other Name: Shaft-Axle Half; Axle Assembly
- Replaces: 68258859AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2015-2023 Dodge Charger | R/T RWD | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 5.7L, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Charger Axle Half Shaft Left
Part Number: 4578733AE
$536.75 MSRP: $812.00
You Save: $275.25 (34%)
ADD TO CART
Product Specifications
- Other Name: Shaft-Axle Half; Axle Assembly
- Position: Driver Side
- Replaces: 4578733AC, 68194755AA, 4578733AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2012-2014 Dodge Charger | Police RWD, SRT RWD, SRT Superbee RWD, SRT8 RWD, SRT8 Superbee RWD | 8 Cyl 6.4L
- 2009-2010 Dodge Charger | Base RWD, R/T RWD, SRT8 RWD | 8 Cyl 6.1L
View related parts
Dodge Charger Axle Half Shaft
Part Number: 4578732AB
$526.85 MSRP: $797.00
You Save: $270.15 (34%)
ADD TO CART
Product Specifications
- Other Name: Shaft-Axle Half
- Replaced by: 4578732AE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009 Dodge Charger | Base RWD, R/T RWD, SRT8 RWD | 8 Cyl 6.1L
View related parts
Dodge Charger Axle Half Shaft
Part Number: 4578733AB
$536.75 MSRP: $812.00
You Save: $275.25 (34%)
ADD TO CART
Product Specifications
- Other Name: Shaft-Axle Half
- Replaced by: 4578733AE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009-2010 Dodge Charger | Base RWD, R/T RWD, SRT8 RWD | 8 Cyl 6.1L
View related parts
Dodge Charger Axle Half Shaft
Part Number: 53010671AD
$501.55 MSRP: $762.00
You Save: $260.45 (35%)
ADD TO CART
Product Specifications
- Other Name: Shaft-Axle Half
- Replaced by: 53010749AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2015 Dodge Charger | Police RWD, Scat Pack RWD, SRT RWD | 8 Cyl 6.4L
View related parts
Dodge Charger Axle Shaft Front Left
Part Number: R4578601AA
$244.15 MSRP: $295.00
You Save: $50.85 (18%)
ADD TO CART
Product Specifications
- Other Name: Shaft-Axle Half; Axle Assembly
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2017-2023 Dodge Charger | GT AWD, Police AWD, SE AWD, SXT AWD | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.6L, 8 Cyl 5.7 L GAS, 8 Cyl 5.7L, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
- 2015 Dodge Charger | Police AWD, SE AWD, SXT AWD | 6 Cyl 3.6L, 8 Cyl 5.7L
- 2007-2010 Dodge Charger | Base AWD, R/T AWD, Rallye AWD, SXT AWD | 6 Cyl 3.5L, 8 Cyl 5.7L
View More
View related parts
Dodge Charger Axle Half Shaft
Part Number: R4578600AA
$245.20 MSRP: $295.00
You Save: $49.80 (17%)
ADD TO CART
Product Specifications
- Other Name: Shaft-Axle Half; Axle Assembly
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2018 Dodge Charger | Base AWD, GT AWD, Police AWD, R/T AWD, Rallye AWD, SE AWD, SXT AWD, V6 AWD | 6 Cyl 3.5L, 6 Cyl 3.6L, 8 Cyl 5.7L
View related parts
Dodge Charger Axle Half Shaft
Part Number: 52123952AD
$356.35 MSRP: $542.00
You Save: $185.65 (35%)
ADD TO CART
Product Specifications
- Other Name: Shaft-Axle Half; Axle Assembly
- Replaces: 52123952AA, 52123952AB, 52123952AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2015-2017 Dodge Charger | Police RWD, SE RWD, SXT RWD | 6 Cyl 3.6L
View related parts
Dodge Charger Axle Shaft Right
Part Number: 53010848AB
$774.35 MSRP: $1185.00
You Save: $410.65 (35%)
ADD TO CART
Product Specifications
- Other Name: Shaft-Axle Half
- Replaced by: 53010848AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2020 Dodge Charger | Police RWD, Scat Pack RWD, SRT Hellcat Widebody RWD | 8 Cyl 6.2L, 8 Cyl 6.4L
View related parts
Dodge Charger Shaft-Axle Half
Part Number: 4578600AB
$433.12 MSRP: $664.00
You Save: $230.88 (35%)
ADD TO CART
Product Specifications
- Other Name: Axle Assembly, Drive Axle
- Position: Passenger Side
- Replaces: 4578600AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2023 Dodge Charger | Base AWD, GT AWD, Police AWD, R/T AWD, Rallye AWD, SE AWD, SXT AWD, V6 AWD | 6 Cyl 3.5L, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.6L, 8 Cyl 5.7 L GAS, 8 Cyl 5.7L, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Charger Axle Half Shaft
Part Number: 53010670AD
$596.15 MSRP: $906.00
You Save: $309.85 (35%)
ADD TO CART
Product Specifications
- Other Name: Shaft-Axle Half
- Replaced by: 53010748AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2015 Dodge Charger | Police RWD, Scat Pack RWD, SRT RWD | 8 Cyl 6.4L
View related parts
Dodge Charger Axle Half Shaft
Part Number: 4578732AC
$526.85 MSRP: $797.00
You Save: $270.15 (34%)
ADD TO CART
Product Specifications
- Other Name: Shaft-Axle Half
- Replaced by: 4578732AE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2010 Dodge Charger | Base RWD, SRT8 RWD | 8 Cyl 6.1L
View related parts
Dodge Charger Axle Half Shaft
Part Number: 4726011AA
$388.25 MSRP: $593.00
You Save: $204.75 (35%)
ADD TO CART
Product Specifications
- Other Name: Shaft-Axle Half
- Replaced by: 4726011AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2012 Dodge Charger | Police RWD, R/T RWD, SE RWD, SRT8 RWD, SRT8 Superbee RWD, SXT RWD | 6 Cyl 3.6L, 8 Cyl 5.7L, 8 Cyl 6.4L
View related parts
Dodge Charger Axle Half Shaft Left
Part Number: 53010849AB
$809.55 MSRP: $1245.00
You Save: $435.45 (35%)
ADD TO CART
Product Specifications
- Other Name: Shaft-Axle Half; Axle Assembly
- Position: Driver Side
- Replaced by: 53010849AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2020 Dodge Charger | Police RWD, Scat Pack RWD, SRT Hellcat Widebody RWD | 8 Cyl 6.2L, 8 Cyl 6.4L
View related parts
Dodge Charger Axle Half Shaft Right
Part Number: 5180492AC
$519.75 MSRP: $759.00
You Save: $239.25 (32%)
Product Specifications
- Other Name: Shaft-Axle Half; Axle Assembly
- Position: Passenger Side
- Replaces: 5180492AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009-2014 Dodge Charger | Police AWD, R/T AWD, SE AWD, SXT AWD, V6 AWD | 6 Cyl 3.6L, 8 Cyl 5.7L

| Page 1 of 4 |Next >

1-20 of 75 Results

Dodge Charger Axle Shaft

The Axle Shaft of Dodge Charger consumes power from the differential and transmits it to drive wheels that rotates independently in order to increase the traction. These steel shafts can be of numerous types, like the solid axles of the current day trucks and the ancient RWD cars, and the half-shafts of vehicles having an independent suspension system. Housing of the differential and axle shafts are of solid axles while the half shaft transmit power from the transaxle to the wheels. Axle shafts may be damaged due to constant impact with the obstacles that make them to develop some problems like noise and vibrations; on the other hand, halfshafts may prove to be faulty due to worn CV Joints and torn boots. On balance, the Axle Shaft has the primary function as bearing the weight of the car, transmitting the necessary amount of torque, and ensuring the correct positioning of the wheels in Dodge Charger automobile models.

Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Dodge Charger Axle Shaft at great affordable prices. Moreover, all genuine Dodge Charger Axle Shaft come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.

Dodge Charger Axle Shaft Parts Questions & Experts Answers

Axle Half Shaft
4578034AE
Q: How to replace a drive axle boot and Axle Shaft on Dodge Charger?
A: If a Axle Shaft boot has failed, the entire shaft assembly must be replaced as boots are not serviceable separately. To remove, start by removing the wheel cover or hub cap and break the Axle Shaft/hub nut loose with a socket and large breaker bar. Block the front wheels to prevent the vehicle from rolling. Loosen the wheel lug nuts, raise the rear of the vehicle, and support it securely on jack stands. Remove the wheel. Remove the Axle Shaft/hub nut and discard it. Drain the gear lubricant from the Differential. Disconnect the driveshaft from the differential and remove the rear exhaust pipe and muffler. Pry the inner CV joint out of the differential just far enough to release the snap-ring. The Axle Shaft can't be removed from the differential until the differential has been lowered. Support the differential with a floor jack. Remove the mounting fasteners securing the differential to the crossmember and differential mount. Carefully lower the differential enough to separate the Axle Shaft(s) from the differential. Pull the Axle Shaft out of the hub flange. If it sticks, tap it out with a soft-faced hammer. Installation is the reverse of removal, noting the following points: Remove the rubber isolation washer from the outer CV joint stub shaft and inspect it. Replace it if necessary. Tighten the differential mounting bolts to the torque. Install a new Axle Shaft/hub nut. Tighten the hub nut securely, but don't try to tighten it to the actual torque specification until you've lowered the vehicle to the ground. Fill the differential with the type and amount of lubricant specified. Install the wheels and lower the vehicle to the ground. Tighten the wheel lug nuts to the torque. Tighten the Axle Shaft/hub nut to the torque. Install the wheel cover or hub cap.