How to check and replace powertrain mounts on Dodge Durango?

There are three powertrain mounts on the vehicles, left and right engine mounts attached to the engine block and frame, and a rear mount attached to the transmission and frame. Engine mounts seldom require attention, but broken or deteriorated mounts should be replaced immediately to prevent damage or wear on the drive line components. To check the mounts, raise the engine slightly to remove the weight from them, then check for relative movement between the inner and outer portions of the mount using a large screwdriver or prybar. If movement is noted, lower the engine and tighten the mount fasteners. Inspect the mounts for cracked, hardened rubber or separation from the metal casing, indicating a need for replacement, and apply rubber preservative to slow deterioration. For replacement, disconnect the cable from the negative terminal of the battery, remove the engine cooling fan and shroud, and raise the front of the vehicle securely on jackstands. Support the engine with a lifting device from above, ensuring not to connect it to the intake manifold, and raise the engine just enough to relieve the weight from the mounts. For 2WD models, remove the engine mount-to-frame support bracket through-bolt, the mount-to-engine block bolts, and then the mount and heat shield if equipped. Place the heat shield and new mount in position, install and tighten the mount-to-engine block bolts. For 4WD models, support the front axle with a floor jack and jackstands, remove the engine skid plate, front crossmember, and bolts supporting the engine mount to the front axle, then remove the engine mount-to-frame support bracket through-bolt and engine support bracket bolt and nuts. Install the new engine mount onto the engine support bracket and tighten the bolts securely. After installing the engine mounts onto the engine, lower the engine while guiding the engine mount and through-bolt into the frame support bracket, then install and tighten the through-bolt nut securely. The remainder of the installation follows the reverse order of removal, after which the engine hoist and jackstands can be removed, and the vehicle lowered.

Genuine Dodge Durango Engine Mount

Engine Motor Mount

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

78 Engine Mounts found

View related parts
Dodge Durango INSULATOR-Engine Mount
Part Number: 68252518AA
$89.65 MSRP: $122.00
You Save: $32.35 (27%)
ADD TO CART
Product Specifications
- Other Name: ISOLATOR Engine Mount; Front Mount, Isolator, Mount, Side Mount
- Replaces: 52124671AF, 68110950AC, 68110950AA, 68110950AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2013-2023 Dodge Durango | Citadel AWD, Citadel RWD, Crew AWD, Crew RWD, GT AWD, GT RWD, Limited AWD, Limited RWD, Pursuit Vehicle AWD, SXT AWD, SXT RWD, Special Service AWD, Special Service RWD | 6 Cyl 3.6 L GAS, 6 Cyl 3.6L, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Durango INSULATOR-Engine Mount
Part Number: 68252522AA
$115.44 MSRP: $154.00
You Save: $38.56 (26%)
ADD TO CART
Product Specifications
- Other Name: ISOLATOR Engine Mount; Front Mount, Isolator, Mount
- Replaces: 68110951AC, 68110951AB, 68110951AA, 52124675AG
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2013-2023 Dodge Durango | Citadel AWD, Citadel RWD, Crew AWD, Crew RWD, Limited AWD, Limited RWD, Pursuit Vehicle AWD, R/T AWD, R/T RWD, Special Service AWD, Special Service RWD | 6 Cyl 3.6 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 5.7L, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Durango ISOLATOR-Engine Mount
Part Number: 5038548AC
$131.88 MSRP: $198.00
You Save: $66.12 (34%)
ADD TO CART
Product Specifications
- Other Name: ISOLATOR Engine Mount; Front Mount, Isolator, Mount
- Replaces: 5038548AB, 5038548AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2018-2023 Dodge Durango | Citadel AWD, Citadel RWD, Pursuit Vehicle AWD, SRT 392 AWD, SRT AWD, Special Service AWD, Special Service RWD | 6 Cyl 3.6 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS, 8 Cyl 6.4L
View related parts
Dodge Durango Transmission Mount
Part Number: 68110244AE
$61.58 MSRP: $90.60
You Save: $29.02 (33%)
ADD TO CART
Product Specifications
- Replaces: 68110244AC, 68110244AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2014-2023 Dodge Durango | Citadel AWD, Limited AWD, Pursuit Vehicle AWD, R/T AWD, SRT AWD, SRT Hellcat AWD, Special Service AWD | 6 Cyl 3.6 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 5.7L, 8 Cyl 6.2 L GAS, 8 Cyl 6.2L, 8 Cyl 6.4 L GAS, 8 Cyl 6.4L
View related parts
Dodge Durango INSULATOR-Engine Mount
Part Number: 68110950AC
$89.65 MSRP: $122.00
You Save: $32.35 (27%)
ADD TO CART
Product Specifications
- Other Name: ISOLATOR Engine Mount
- Replaced by: 68252518AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2014-2015 Dodge Durango | Citadel AWD, Citadel RWD, Limited AWD, Limited RWD, Special Service AWD, Special Service RWD, SXT AWD, SXT RWD | 6 Cyl 3.6L
View related parts
Dodge Durango INSULATOR-Transmission Mount
Part Number: 5154807AE
$97.18 MSRP: $147.00
You Save: $49.82 (34%)
ADD TO CART
Product Specifications
- Other Name: Mount, Transmission Mount
- Replaces: 5154807AD, 5154807AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2014-2023 Dodge Durango | Citadel AWD, GT AWD, Limited AWD, Pursuit Vehicle AWD, SXT AWD, Special Service AWD | 6 Cyl 3.6 L GAS, 6 Cyl 3.6L, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Durango INSULATOR-Engine Mount
Part Number: 68110950AB
$78.98 MSRP: $122.00
You Save: $43.02 (36%)
ADD TO CART
Product Specifications
- Other Name: ISOLATOR Engine Mount
- Replaced by: 68252518AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2013 Dodge Durango | Citadel AWD, Citadel RWD, Crew AWD, Crew RWD, Special Service AWD, Special Service RWD, SXT AWD, SXT RWD | 6 Cyl 3.6L
View related parts
Dodge Durango INSULATOR-Engine Mount
Part Number: 68110951AB
$101.63 MSRP: $154.00
You Save: $52.37 (35%)
ADD TO CART
Product Specifications
- Other Name: ISOLATOR Engine Mount
- Replaced by: 68252522AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2013 Dodge Durango | Citadel AWD, Citadel RWD, Crew AWD, Crew RWD, R/T AWD, R/T RWD, Special Service AWD, Special Service RWD | 8 Cyl 5.7L
View related parts
Dodge Durango Bracket-Engine Mount
Part Number: 68275987AA
$91.56 MSRP: $138.00
You Save: $46.44 (34%)
ADD TO CART
Product Specifications
- Other Name: Bracket Engine Mount; Mount Bracket
- Position: Driver Side
- Replaces: 52124989AC, 52124989AD, 52124989AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2023 Dodge Durango | Citadel AWD, Citadel RWD, Crew AWD, Crew RWD, Limited AWD, Limited RWD, Pursuit Vehicle AWD, R/T AWD, R/T RWD, SRT 392 AWD, SRT AWD, SRT Hellcat AWD, Special Service AWD, Special Service RWD | 6 Cyl 3.6 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 5.7L, 8 Cyl 6.2 L GAS, 8 Cyl 6.2L, 8 Cyl 6.4 L GAS, 8 Cyl 6.4L
View related parts
Dodge Durango INSULATOR-Engine Mount
Part Number: 68110951AC
$101.63 MSRP: $154.00
You Save: $52.37 (35%)
ADD TO CART
Product Specifications
- Other Name: ISOLATOR Engine Mount
- Replaced by: 68252522AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2014-2015 Dodge Durango | Citadel AWD, Citadel RWD, Limited AWD, Limited RWD, R/T AWD, R/T RWD, Special Service AWD, Special Service RWD | 8 Cyl 5.7L
View related parts
Dodge Durango ENGINE
Part Number: 68417512AB
$132.08 MSRP: $175.00
You Save: $42.92 (25%)
ADD TO CART
Product Specifications
- Replaces: 68196239AC, 68196239AA, 68196239AB, 68417512AA, 68046260AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2023 Dodge Durango | Citadel AWD, Citadel RWD, Crew AWD, Crew RWD, Limited AWD, Limited RWD, Pursuit Vehicle AWD, R/T AWD, R/T RWD, Special Service AWD, Special Service RWD | 6 Cyl 3.6 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 5.7L, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
- 2009 Dodge Durango | Adventurer 4WD, Limited 2WD, Limited 4WD, Limited HEV 4WD, SE 2WD, SLT 2WD, SLT 4WD | 8 Cyl 5.7L
View related parts
Dodge Durango Transmission Mount
Part Number: 68032665AF
$64.92 MSRP: $97.85
You Save: $32.93 (34%)
ADD TO CART
Product Specifications
- Replaces: 68032665AD, 68032665AE, 68032666AC, 68032665AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2023 Dodge Durango | Citadel AWD, Citadel RWD, Crew AWD, Crew RWD, Limited RWD, R/T AWD, R/T RWD, Special Service AWD, Special Service RWD | 6 Cyl 3.6 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 5.7L, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Durango ISOLATOR-Engine Mount
Part Number: 5038830AB
$107.35 MSRP: $162.00
You Save: $54.65 (34%)
ADD TO CART
Product Specifications
- Other Name: Front Mount, Isolator, Mount
- Replaces: 5038830AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2023 Dodge Durango | 6 Cyl 3.6 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
- 2021 Dodge Durango | SRT Hellcat AWD | 8 Cyl 6.2L
View related parts
Dodge Durango INSULATOR-Engine Mount
Part Number: 52855588AD
$47.79 MSRP: $67.85
You Save: $20.06 (30%)
ADD TO CART
Product Specifications
- Other Name: Insulator Engine Mount; Front Insulator, Front Mount, Mount
- Position: Passenger Side
- Replaces: 52855588AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2009 Dodge Durango | Adventurer 2WD, Limited 2WD, SE 2WD, SLT 2WD, SXT 2WD | 6 Cyl 3.7L, 8 Cyl 4.7L
View related parts
Dodge Durango Transmission Mount
Part Number: 68032662AF
$50.80 MSRP: $74.80
You Save: $24.00 (33%)
ADD TO CART
Product Specifications
- Other Name: Mount
- Replaces: 68032662AD, 68032662AE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2013-2023 Dodge Durango | Citadel RWD, Crew RWD, GT RWD, Limited RWD, SXT RWD, Special Service RWD | 6 Cyl 3.6 L GAS, 6 Cyl 3.6L, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS
View related parts
Dodge Durango INSULATOR-Engine Mount
Part Number: 52855539AE
$191.18 MSRP: $286.00
You Save: $94.82 (34%)
ADD TO CART
Product Specifications
- Other Name: Insulator Engine Mount
- Position: Driver Side
- Replaces: 52855539AC, 52855539AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2009 Dodge Durango | Adventurer 4WD, Limited 4WD, SE 4WD, SLT 4WD, SXT 4WD | 8 Cyl 4.7L, 8 Cyl 5.7L
View related parts
Dodge Durango Bracket-Engine Mount
Part Number: 52124987AB
$46.54 MSRP: $68.70
You Save: $22.16 (33%)
ADD TO CART
Product Specifications
- Other Name: Bracket Engine Mount
- Replaced by: 68252524AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2015 Dodge Durango | Citadel AWD, Citadel RWD, Crew AWD, Crew RWD, Express AWD, Express RWD, Heat AWD, Heat RWD, Limited AWD, Limited RWD, Special Service AWD, Special Service RWD, SXT AWD, SXT RWD | 6 Cyl 3.6L
View related parts
Dodge Durango INSULATOR-Engine Mount
Part Number: 52855843AC
$63.33 MSRP: $95.55
You Save: $32.22 (34%)
ADD TO CART
Product Specifications
- Other Name: Insulator Engine Mount
- Replaced by: 52855843AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008 Dodge Durango | Adventurer 2WD, Limited 2WD, SLT 2WD, SXT 2WD | 8 Cyl 5.7L
View related parts
Dodge Durango Bracket-Engine Mount
Part Number: 52124989AC
$91.56 MSRP: $138.00
You Save: $46.44 (34%)
ADD TO CART
Product Specifications
- Other Name: Bracket Engine Mount
- Replaced by: 68275987AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2013 Dodge Durango | Citadel AWD, Citadel RWD, Crew AWD, Crew RWD, R/T AWD, R/T RWD, Special Service AWD, Special Service RWD | 8 Cyl 5.7L
View related parts
Dodge Durango Bracket-Transmission Mount
Part Number: 68275990AA
$89.22 MSRP: $134.00
You Save: $44.78 (34%)
ADD TO CART
Product Specifications
- Other Name: Bracket Transmission Mount; Transmission Mount Bracket
- Replaces: 68103009AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2014-2023 Dodge Durango | Citadel RWD, Limited RWD, R/T RWD, Special Service RWD | 6 Cyl 3.6 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 5.7L, 8 Cyl 6.2 L GAS, 8 Cyl 6.4 L GAS

| Page 1 of 4 |Next >

1-20 of 78 Results

Dodge Durango Engine Mount

The Engine Mount in Dodge Durango vehicles serves two primary functions: It muffles noise causing from the operation of the engine, while at the same time offering support and retaining the position of the engine with the chassis. This is important in achieving these objectives because slick roads can cause slippage thereby affecting the comfort and safety of the car as well as the efficiency of the vehicle's components. Engine Mounts that have been used on Dodge Durango models include the conventional rubber Engine Mounts, fluid filled hydraulic Engine Mounts and recently developed electronic active Engine Mounts. Constructional mounts are made of metal parts sandwiched in between rubber layers whereas hydraulic type incorporates greater amount of damping. New active mounts latest active mounts vary the degrees of stiffness depending on the engine's RPM for the optimal performance. Dodge Durango Engine Mounts can end up getting weak from age, heat or simply get damaged by fluids and as a result, they may become spongy or they may start leaking. Their importance is evident in the effective working of the car hence they should be inspected from time to time to check their structural soundness.

Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Dodge Durango Engine Mount at great affordable prices. Moreover, all genuine Dodge Durango Engine Mount come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.

Dodge Durango Engine Mount Parts Questions & Experts Answers

INSULATOR-Engine Mount
52855539AD
Q: How to check and replace powertrain mounts on Dodge Durango?
A: There are three powertrain mounts on the vehicles, left and right engine mounts attached to the engine block and frame, and a rear mount attached to the transmission and frame. Engine mounts seldom require attention, but broken or deteriorated mounts should be replaced immediately to prevent damage or wear on the drive line components. To check the mounts, raise the engine slightly to remove the weight from them, then check for relative movement between the inner and outer portions of the mount using a large screwdriver or prybar. If movement is noted, lower the engine and tighten the mount fasteners. Inspect the mounts for cracked, hardened rubber or separation from the metal casing, indicating a need for replacement, and apply rubber preservative to slow deterioration. For replacement, disconnect the cable from the negative terminal of the battery, remove the engine cooling fan and shroud, and raise the front of the vehicle securely on jackstands. Support the engine with a lifting device from above, ensuring not to connect it to the Intake Manifold, and raise the engine just enough to relieve the weight from the mounts. For 2WD models, remove the engine mount-to-frame support bracket through-bolt, the mount-to-engine block bolts, and then the mount and heat shield if equipped. Place the heat shield and new mount in position, install and tighten the mount-to-engine block bolts. For 4WD models, support the front axle with a floor jack and jackstands, remove the engine skid plate, front crossmember, and bolts supporting the engine mount to the front axle, then remove the engine mount-to-frame support bracket through-bolt and engine support bracket bolt and nuts. Install the new engine mount onto the engine support bracket and tighten the bolts securely. After installing the engine mounts onto the engine, lower the engine while guiding the engine mount and through-bolt into the frame support bracket, then install and tighten the through-bolt nut securely. The remainder of the installation follows the reverse order of removal, after which the engine hoist and jackstands can be removed, and the vehicle lowered.