×
- Live Chat
- 1-888-511-3595
My Garage
My Account
Cart
Genuine Dodge Durango Pushrod
Valve Push Rod- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
7 Pushrods found
Dodge Durango Pushrod
Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Dodge Durango Pushrod at great affordable prices. Moreover, all genuine Dodge Durango Pushrod come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.
Dodge Durango Pushrod Parts Questions & Experts Answers
- Q: How do you remove and install Pushrod and rocker arm in 5.7L V8 engine on Dodge Durango?A: To do this you will need to remove the valve covers from the cylinder heads and the bolts that hold the rocker arm shafts in place and these bolts are the center bolts followed by the bolts at the extremity of the rocker arm shafts. After the last nut is fully loosened, carefully lift the rocker shaft assembly off of the cylinder head, being sure note the position betwen the upper intake and lower exhaust rocker arms so that they can be reassembled in their original orientation. Rocker arm positions should be recorded in order to reinstall them in the correct position; each set of components should be replaced and stored as they were found; and the pushrods should be removed and stored in an order to avoid crossing them up. It is important for one to note that exhaust pushrods are a little longer than intake pushrods not interchangeable. If the cylinder heads have been machined to a standard of flatness then it is crucial to 'shorten' the appropriate length pushrods to cover the now shorter distances of the rocker arms to the Camshaft dimensions, unless consulting with a machine shop. For each rocker arm, check if there is wear, cracks, and damage on the surface that comes into contact with pushrods and or valve stems, and the rocker arm shafts and the bores should also be checked to establish if they have worn out and or damaged, a worn out or damaged part must be replaced. There must be free passage into the hole at the pushrod end of each rocker arm; bears checking for crackline and abnormal wear, pushrods can be rolled across a flat surface to check for bend. Coat the lower end of each pushrod with clean engine oil or assembly lube and install these into their original position and ensure that it seals fully into the lifter socket. Coat the valve stems and the upper ends of the pushrods with assembly lube for protection of any mating surfaces during initial start up, then lubricate the rocker shafts, the rocker shaft assembly should have all components located in their original positions before being installed in to the head of the cylinder. Tighten the rocker arm shafts beginning with the centre bolt, in a preset sequence till the appropriate torque is secured so that the pushrods fit tightly in the rocker arms. If bolts when installed appear light before the shaft is seated or if pushrods bind, all the components inside should be examined. Last, put the valve covers back on, crank up the engine, scan for valve train rattles and knock and look for oil leaks at the gaskets.
Related Dodge Durango Parts
Dodge Durango Thermostat Housing
Dodge Durango Timing Cover
Dodge Durango Thermostat
Dodge Durango Valve Stem Seal
Dodge Durango Timing Chain
Dodge Durango Timing Chain Guide
Dodge Durango Timing Chain Tensioner
Dodge Durango Transfer Case Output Shaft Snap Ring
Dodge Durango Valve Cover Gasket
Browse by Year
2023 Pushrod 2022 Pushrod 2021 Pushrod 2020 Pushrod 2019 Pushrod 2018 Pushrod 2017 Pushrod 2016 Pushrod 2015 Pushrod 2014 Pushrod 2013 Pushrod 2012 Pushrod 2011 Pushrod 2009 Pushrod 2008 Pushrod 2007 Pushrod 2006 Pushrod 2005 Pushrod 2004 Pushrod 2003 Pushrod 2002 Pushrod 2001 Pushrod 2000 Pushrod 1999 Pushrod 1998 Pushrod