×
- Live Chat
- 1-888-511-3595
My Garage
My Account
Cart
Genuine Dodge Magnum Automatic Transmission Filter
AT Filter- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
4 Automatic Transmission Filters found
Dodge Magnum Filter-Transmission Oil
Part Number: 52108325AA$37.93 MSRP: $51.85You Save: $13.92 (27%)
Dodge Magnum Filter-Transmission Oil
Part Number: 52852913AB$38.70 MSRP: $57.85You Save: $19.15 (34%)
Dodge Magnum Filter-Transmission Regulator Valve
Part Number: 3878313$2.95 MSRP: $4.35You Save: $1.40 (33%)
Dodge Magnum Automatic Transmission Filter
Automatic Transmission Filter can be considered as another significant component in Dodge Magnum vehicles which serve to control the state of the transmission system. Its primary function is to capture contaminants in gear transverse so as to avoid blocking small orifices and hinder movement of components in motion. Firstly only this filtration helps in maintaining the adequate function of the companies' transmission function and their longevity. There are various types of Automatic Transmission Filters used in Dodge Magnum vehicles which include, those filters that are inside the transmission where normally one has two removeable fluid pans & external spin-on type or cartridge type filters. It is important to note that whilst some filters are built to be easy to reach and to be changed often there are others that are harder to reach, and some manufacturers may state that they are "lifetime" filters. Furthermore, in-line transmittance filters may be used to upgrade on the filtration without necessarily affecting the stream of the fluid. On the whole, the Automatic Transmission Filter is critically important to the Magnum internal combustion engine functioning since it stabilizes fuel consumption, lowers temperature levels, and increases the car' service lifetime. It is therefore important to carry out routine check up on the Automatic Transmission Filter in order to prevent damage and expenses incurred in the process of repairs.
Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Dodge Magnum Automatic Transmission Filter at great affordable prices. Moreover, all genuine Dodge Magnum Automatic Transmission Filter come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.
Dodge Magnum Automatic Transmission Filter Parts Questions & Experts Answers
- Q: How to drain and replace transmission fluid and Automatic Transmission Filter in a Dodge Magnum?A: At specified time intervals, drain and replace the transmission fluid after the vehicle has completely cooled down. Before starting, purchase the recommended transmission fluid and a new filter. Additionally, gather tools such as jack stands, a drain pan, newspapers, and clean rags. Raise and support the vehicle on jack stands. Place a drain pan and remove the front and side transmission pan mounting bolts. Loosen the rear pan bolts and carefully pry the transmission pan loose with a screwdriver to allow the fluid to drain. Remove the remaining bolts, pan, and gasket, and clean the gasket surface of the transmission. Drain the fluid from the pan, clean it with solvent, and dry it with compressed air. Remove the filter and seal, then install a new filter seal and the new filter. Ensure the gasket surface on the transmission pan is clean. Install a new gasket if working on a NAG1 transmission, or clean the pan and transmission surfaces with lacquer thinner and apply ATF-resistant RTV sealant if working on a 42LE transmission. Bolt the pan in place and tighten the bolts gradually until the final torque figure is reached. Lower the vehicle and add the specified amount of automatic transmission fluid through the filler tube. Check for leaks during the first few trips. To check the fluid level, start the engine with the parking brake set and move the shift lever through all gear ranges, ending in Neutral. Wait for at least 2 minutes. With the transmission at normal operating temperature, insert the dipstick into the filler tube and note the fluid level. Use a scan tool to check the temperature of the fluid and determine the correct fluid level using the temperature and the height of the fluid on the dipstick. If additional fluid is required, add it directly into the tube using a funnel and check the level until it's correct. Finally, install the dipstick tube cap.
