×
- Live Chat
- 1-888-511-3595
My Garage
My Account
Cart
Genuine Dodge Ram 1500 Rocker Arm
Engine Rocker Arm- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
20 Rocker Arms found
Dodge Ram 1500 Engine Intake Rocker Arm
Part Number: 5011431AB$166.52 MSRP: $253.00You Save: $86.48 (35%)
Dodge Ram 1500 Engine Rocker Arm Kit
Part Number: 53020742AB$28.39 MSRP: $42.70You Save: $14.31 (34%)
Dodge Ram 1500 Engine Intake Rocker Arm
Part Number: 53021552AA$139.75 MSRP: $210.00You Save: $70.25 (34%)
Dodge Ram 1500 Engine Intake Rocker Arm
Part Number: 68060343AA$139.75 MSRP: $210.00You Save: $70.25 (34%)
Dodge Ram 1500 Rocker Arm
In the Dodge Ram 1500 car models, the Rocker Arm plays a significant part in the engine's valvetrain mechanism, its main function is to transfer the motion from the pushrod to the intake and exhaust valves. Usually made of stamped steel or aluminum with a strong solid design, the Rocker Arm move vertically through the push rod push and change it into the required amount of force to actuate the valves. Aluminum is used for its lightweight characteristics particularly in high-RPM operations while cast iron or forged carbon steel is employed in diesel operations due to their robustness. Some of the Rocker Arms which may be found in Dodge Ram 1500 models are the standard and the roller rockers. Roller rockers which do not require use of bearings to lessen friction are appropriate for the overhead valve as well as the overhead camshaft engines. The rocker ratio which for modern engines is between 1.5: 1 and 1.8: 1 can increase camshaft lift and hence enhance the performance of the engine. Higher revving engines of the Dodge Ram 1500 also feature upgraded fulcrum bearings to deal with the stress and to provide extra strength.
Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Dodge Ram 1500 Rocker Arm at great affordable prices. Moreover, all genuine Dodge Ram 1500 Rocker Arm come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.
Dodge Ram 1500 Rocker Arm Parts Questions & Experts Answers
- Q: How do you remove and install the rocker arms and pushrods in Hemi engine on Dodge Ram 1500?A: First, take out and examine rocker arms and pushrods after removing the valve covers from cylinder heads. So, get yourself special pushrod retainer tool #9070 or its equivalent to ensure that the pushrods remain in place. Go on gradually loosening the rocker arm shaft bolts off starting with center bolts towards end. To remove this fully, lift the entire rocker shaft assembly off the cylinder head keeping in mind that retainers must remain under bolt head. Therefore keep record of every rocker arm posture since it is required to put them back to their original position. The intake rockers are marked "I" so store each set of rocker components correspondingly. Remove and put away push rods to hold them onto their initial positions as they were before removal or disassembling for maintenance purposes. Nevertheless remember that exhaust push-rods are a little bit longer than intake ones and cannot be replaced between themselves . In addition check each rocker arm for wear, cracks or damage especially where they contact the pushrods and valve stems during inspection periods. Also check for wear, galling, stress cracks, or unusual wear patterns on rocker arm shafts and bores of the arms themselves. Replace any worn or damaged rocker arms and shafts immediately . Never attempt to take out these retainers unless it becomes necessary because they can break down into your engine system. If a retainer breaks defeat it from the rocker arm shaft prior to reassemblying then install rockers again when broken . The last thing is installing/fitting/inserting/lodging both ends of all (the) pushrods; lubricate these pieces , apply engine assembly lube to valve stem ends/upper end portion/surface of valve stem along with top end surfaces of push rods; lubricate the rockershaf and install/co-locate/place/push together again other parts including such as valves in each original position on each head in which case the shaft of rockers is assembled. Sequence and torque the rocker arm shaft bolts to specification at several steps taking care that push - rods are seated properly. Finally put on valve covers, start the engine, and check for any unusual noises from or oil leaks around O-rings.
