How to Remove and Install a Steering Knuckle on Dodge Ram 1500?

Loosen the wheel lug nuts, raise the vehicle and support it securely on jackstands. Remove the wheel. On 4WD models, unscrew the driveaxle/hub nut with a socket and large breaker bar. Brace a large prybar across two of the wheel studs or insert a large screwdriver through the center of the brake caliper and into the disc cooling vanes to prevent the hub from turning as the nut is loosened. Remove the disc brake caliper and disc. If equipped, disconnect the electrical connector from the wheel speed sensor and remove the sensor. Disconnect the tie-rod from the steering knuckle. Remove the driveaxle/hub nut. Support the lower control arm with a floor jack. Separate the lower control arm from the steering knuckle. Separate the upper control arm from the steering knuckle. Remove the knuckle. Carefully inspect the steering knuckle for cracks, especially around the steering arm and spindle mounting area. Also inspect the balljoint stud holes. if they're elongated, or if you find any cracks in the knuckle, replace the steering knuckle. Installation is the reverse of removal. Tighten all suspension fasteners. Loosen the wheel lug nuts, raise the vehicle and support it securely on jackstands. Remove the wheel. Remove the hub bearing and axle shaft. Disconnect the tie-rod end or drag link from the steering knuckle. Remove the wheel speed sensor. Loosen the steering knuckle upper ballstud nut a few turns, but don't remove it. Remove the lower balljoint nut. Use a balljoint separation tool to detach the balljoint from the knuckle. Remove the upper balljoint nut. Separate the steering knuckle. Use a brass hammer to knock it loose if necessary. Installation is the reverse of removal. Tighten all suspension fasteners.

Genuine Dodge Ram 1500 Steering Knuckle

Front Steering Knuckle

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

27 Steering Knuckles found

View related parts
Dodge Ram 1500 Front Steering Knuckle
Part Number: 52106553AC
$386.10 MSRP: $591.00
You Save: $204.90 (35%)
ADD TO CART
Product Specifications
- Other Name: Knuckle-Front
- Replaced by: 68044703AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2003-2008 Dodge Ram 1500 | Laramie Quad Cab 4WD, Laramie Regular Cab 4WD, SLT Quad Cab 4WD, SLT Regular Cab 4WD, ST Quad Cab 4WD, ST Regular Cab 4WD | 8 Cyl 4.7L, 8 Cyl 5.7L, 8 Cyl 5.9L
View related parts
Dodge Ram 1500 Suspension Knuckle Front Left
Part Number: 68044703AA
$386.10 MSRP: $591.00
You Save: $204.90 (35%)
ADD TO CART
Product Specifications
- Other Name: Knuckle-Front
- Replaced by: 68044703AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009-2010 Dodge Ram 1500 | Laramie Crew Cab 4WD, Laramie Quad Cab 4WD, SLT Crew Cab 4WD, SLT HEV Crew Cab 4WD, SLT Quad Cab 4WD, SLT Regular Cab 4WD, ST Crew Cab 4WD, ST Quad Cab 4WD, ST Regular Cab 4WD | 8 Cyl 4.7L, 8 Cyl 5.7L
View related parts
Dodge Ram 1500 Front KNUCKLE
Part Number: 68044700AB
$361.58 MSRP: $814.00
You Save: $452.42 (56%)
ADD TO CART
Product Specifications
- Other Name: Knuckle-Front
- Replaced by: 68044700AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2010 Dodge Ram 1500 | Laramie Crew Cab 2WD, Laramie Quad Cab 2WD, SLT Crew CAB 2WD, SLT Quad Cab 2WD, SLT Regular Cab 2WD, ST Crew Cab 2WD, ST Quad Cab 2WD, ST Regular Cab 2WD | 6 Cyl 3.7L, 8 Cyl 4.7L, 8 Cyl 5.7L
View related parts
Dodge Ram 1500 Aluminum Front Left Spindle Knuckle
Part Number: 52106551AB
$534.60 MSRP: $814.00
You Save: $279.40 (35%)
ADD TO CART
Product Specifications
- Other Name: Knuckle-Front
- Replaced by: 68044701AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2002-2008 Dodge Ram 1500 | Laramie Quad Cab 2WD, Laramie Regular Cab 2WD, Quad Cab 2WD, Regular Cab 2WD, SLT Quad Cab 2WD, SLT Regular Cab 2WD, SRT-10 Quad Cab 2WD, SRT-10 Regular Cab 2WD, ST Quad Cab 2WD, ST Regular Cab 2WD | 10 Cyl 8.3L, 6 Cyl 3.7L, 8 Cyl 4.7L, 8 Cyl 5.7L, 8 Cyl 5.9L
View related parts
Dodge Ram 1500 Front Steering Knuckle
Part Number: 52106550AB
$361.58 MSRP: $814.00
You Save: $452.42 (56%)
ADD TO CART
Product Specifications
- Other Name: Knuckle-Front
- Position: Front
- Replaced by: 68044700AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2002-2008 Dodge Ram 1500 | Laramie Quad Cab 2WD, Laramie Regular Cab 2WD, Quad Cab 2WD, Regular Cab 2WD, SLT Quad Cab 2WD, SLT Regular Cab 2WD, SRT-10 Quad Cab 2WD, SRT-10 Regular Cab 2WD, ST Quad Cab 2WD, ST Regular Cab 2WD | 10 Cyl 8.3L, 6 Cyl 3.7L, 8 Cyl 4.7L, 8 Cyl 5.7L, 8 Cyl 5.9L
View related parts
Dodge Ram 1500 Front Steering Knuckle
Part Number: 52106552AC
$404.80 MSRP: $618.00
You Save: $213.20 (35%)
ADD TO CART
Product Specifications
- Other Name: Knuckle-Front
- Position: Front
- Replaced by: 68044704AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2003-2008 Dodge Ram 1500 | Laramie Quad Cab 4WD, Laramie Regular Cab 4WD, SLT Quad Cab 4WD, SLT Regular Cab 4WD, ST Quad Cab 4WD, ST Regular Cab 4WD | 8 Cyl 4.7L, 8 Cyl 5.7L, 8 Cyl 5.9L
View related parts
Dodge Ram 1500 Front Steering Knuckle
Part Number: 68044704AA
$404.80 MSRP: $618.00
You Save: $213.20 (35%)
ADD TO CART
Product Specifications
- Other Name: Knuckle-Front
- Replaced by: 68044704AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009-2010 Dodge Ram 1500 | Laramie Crew Cab 4WD, Laramie Quad Cab 4WD, SLT Crew Cab 4WD, SLT HEV Crew Cab 4WD, SLT Quad Cab 4WD, SLT Regular Cab 4WD, ST Crew Cab 4WD, ST Quad Cab 4WD, ST Regular Cab 4WD | 8 Cyl 4.7L, 8 Cyl 5.7L
View related parts
Dodge Ram 1500 Front Steering Knuckle
Part Number: 68044701AA
$534.60 MSRP: $814.00
You Save: $279.40 (35%)
ADD TO CART
Product Specifications
- Other Name: Knuckle-Front
- Replaced by: 68044701AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009 Dodge Ram 1500 | Laramie Crew Cab 2WD, Laramie Quad Cab 2WD, SLT Crew CAB 2WD, SLT Quad Cab 2WD, SLT Regular Cab 2WD, ST Crew Cab 2WD, ST Quad Cab 2WD, ST Regular Cab 2WD | 6 Cyl 3.7L, 8 Cyl 4.7L, 8 Cyl 5.7L
View related parts
Dodge Ram 1500 Front Steering Knuckle
Part Number: 68044701AB
$534.60 MSRP: $814.00
You Save: $279.40 (35%)
ADD TO CART
Product Specifications
- Other Name: Knuckle-Front
- Replaced by: 68044701AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2010 Dodge Ram 1500 | Laramie Crew Cab 2WD, Laramie Quad Cab 2WD, SLT Crew CAB 2WD, SLT Quad Cab 2WD, SLT Regular Cab 2WD, ST Crew Cab 2WD, ST Quad Cab 2WD, ST Regular Cab 2WD | 6 Cyl 3.7L, 8 Cyl 4.7L, 8 Cyl 5.7L
View related parts
Dodge Ram 1500 Front Steering Knuckle
Part Number: 68044700AA
$361.58 MSRP: $814.00
You Save: $452.42 (56%)
ADD TO CART
Product Specifications
- Other Name: Knuckle-Front
- Replaced by: 68044700AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009 Dodge Ram 1500 | Laramie Crew Cab 2WD, Laramie Quad Cab 2WD, SLT Crew CAB 2WD, SLT Quad Cab 2WD, SLT Regular Cab 2WD, ST Crew Cab 2WD, ST Quad Cab 2WD, ST Regular Cab 2WD | 6 Cyl 3.7L, 8 Cyl 4.7L, 8 Cyl 5.7L
View related parts
Dodge Ram 1500 KNUCKLE Asm
Part Number: 4778592
Product Specifications
- Other Name: KNUCKLE, Front Axle; Knuckle
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1994-1997 Dodge Ram 1500 | 3-Person Cab 4WD, Club Cab 4WD, Club Cab 6FT BOX 4WD, Club Cab 8FT BOX 4WD, Regular Cab 4WD, Regular Cab 6FT BOX 4WD, Regular Cab 8FT BOX 4WD | 8 Cyl 5.2L, 8 Cyl 5.9L
View related parts
Dodge Ram 1500 KNUCKLE Asm
Part Number: 4778593
Product Specifications
- Other Name: KNUCKLE, Front Axle; Knuckle
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1994-1997 Dodge Ram 1500 | 3-Person Cab 4WD, Club Cab 4WD, Club Cab 6FT BOX 4WD, Club Cab 8FT BOX 4WD, Regular Cab 4WD, Regular Cab 6FT BOX 4WD, Regular Cab 8FT BOX 4WD | 8 Cyl 5.2L, 8 Cyl 5.9L
View related parts
Dodge Ram 1500 KNUCKLE Asm
Part Number: 4778604
Product Specifications
- Other Name: KNUCKLE, Front Axle; Knuckle
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1994-1996 Dodge Ram 1500 | 3-Person Cab 4WD, Club Cab 4WD, Regular Cab 4WD | 8 Cyl 5.2L, 8 Cyl 5.9L
View related parts
Dodge Ram 1500 Front Steering Knuckle
Part Number: 5003048AA
Product Specifications
- Other Name: Knuckle-Front; Knuckle
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1998-1999 Dodge Ram 1500 | Club Cab 4WD, Quad Cab 4WD, Regular Cab 4WD | 8 Cyl 5.2L, 8 Cyl 5.9L
View related parts
Dodge Ram 1500 Knuckle
Part Number: 5003049AA
Product Specifications
- Other Name: Knuckle Front
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1998-1999 Dodge Ram 1500 | Club Cab 4WD, Quad Cab 4WD, Regular Cab 4WD | 8 Cyl 5.2L, 8 Cyl 5.9L
View related parts
Dodge Ram 1500 Suspension Knuckle Front Left
Part Number: 5015135AB
Product Specifications
- Other Name: Knuckle-Front; Knuckle
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001 Dodge Ram 1500 | Club Cab 4WD, Quad Cab 4WD, Regular Cab 4WD | 8 Cyl 5.2L, 8 Cyl 5.9L
View related parts
Dodge Ram 1500 Knuckle Front
Part Number: 52037681
Product Specifications
- Other Name: Knuckle
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1994-1999 Dodge Ram 1500 | 3-Person Cab 2WD, Club Cab 2WD, Club Cab 6FT BOX 2WD, Club Cab 8FT BOX 2WD, Quad Cab 2WD, Regular Cab 2WD, Regular Cab 6FT BOX 2WD, Regular Cab 8FT BOX 2WD | 6 Cyl 3.9L, 8 Cyl 5.2L, 8 Cyl 5.9L
View related parts
Dodge Ram 1500 Knuckle Front
Part Number: 52037683
Product Specifications
- Other Name: Knuckle
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1994-1996 Dodge Ram 1500 | 3-Person Cab 2WD, Club Cab 2WD, Regular Cab 2WD | 6 Cyl 3.9L, 8 Cyl 5.2L, 8 Cyl 5.9L
View related parts
Dodge Ram 1500 Front Steering Knuckle
Part Number: 5290460AA
Product Specifications
- Other Name: Knuckle-Front; Knuckle
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2005 Dodge Ram 1500 | SLT Quad Cab 2WD, SRT-10 Quad Cab 2WD, ST Quad Cab 2WD | 10 Cyl 8.3L, 6 Cyl 3.7L, 8 Cyl 4.7L, 8 Cyl 5.7L
View related parts
Dodge Ram 1500 Front Steering Knuckle
Part Number: 5290461AA
Product Specifications
- Other Name: Knuckle-Front; Knuckle
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2005 Dodge Ram 1500 | SLT Quad Cab 2WD, SRT-10 Quad Cab 2WD, ST Quad Cab 2WD | 10 Cyl 8.3L, 6 Cyl 3.7L, 8 Cyl 4.7L, 8 Cyl 5.7L

| Page 1 of 2 |Next >

1-20 of 27 Results

Dodge Ram 1500 Steering Knuckle

The Steering Knuckle of Dodge Ram 1500 vehicles are part of the vehicle's suspension and steering system, it act as a part that connects the suspension and steering systems to the front wheels. It has holes for the control arms, tie-rod ends and the spindle or hubs this design allowing the suspension to move vertically in response to the road and horizontally for the purpose of steering. Dodge Ram 1500 Steering Knuckles differ between the drive modes and configurations, the RWD and FWD/ AWD/4WD Steering Knuckles are different. RWD platform designs can include an integrated spindle as for FWD/AWD/4WD models, the drive axle extends through the Steering Knuckle. The general development of the Steering Knuckle is characterized by the change of the kingpin to the modern ball joint part, which has become familiar with almost all automobiles.

Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Dodge Ram 1500 Steering Knuckle at great affordable prices. Moreover, all genuine Dodge Ram 1500 Steering Knuckle come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.

Dodge Ram 1500 Steering Knuckle Parts Questions & Experts Answers

Suspension Knuckle Front Left
68044703AA
Q: How to Remove and Install a Steering Knuckle on Dodge Ram 1500?
A: Loosen the wheel lug nuts, raise the vehicle and support it securely on jackstands. Remove the wheel. On 4WD models, unscrew the driveaxle/hub nut with a socket and large breaker bar. Brace a large prybar across two of the wheel studs or insert a large screwdriver through the center of the brake caliper and into the disc cooling vanes to prevent the hub from turning as the nut is loosened. Remove the disc brake caliper and disc. If equipped, disconnect the electrical connector from the wheel speed sensor and remove the sensor. Disconnect the tie-rod from the steering knuckle. Remove the driveaxle/hub nut. Support the lower Control Arm with a floor jack. Separate the lower control arm from the steering knuckle. Separate the upper control arm from the steering knuckle. Remove the knuckle. Carefully inspect the steering knuckle for cracks, especially around the steering arm and spindle mounting area. Also inspect the balljoint stud holes. if they're elongated, or if you find any cracks in the knuckle, replace the steering knuckle. Installation is the reverse of removal. Tighten all suspension fasteners. Loosen the wheel lug nuts, raise the vehicle and support it securely on jackstands. Remove the wheel. Remove the hub bearing and axle shaft. Disconnect the tie-rod end or drag link from the steering knuckle. Remove the wheel speed sensor. Loosen the steering knuckle upper ballstud nut a few turns, but don't remove it. Remove the lower balljoint nut. Use a balljoint separation tool to detach the balljoint from the knuckle. Remove the upper balljoint nut. Separate the steering knuckle. Use a brass hammer to knock it loose if necessary. Installation is the reverse of removal. Tighten all suspension fasteners.

Related Dodge Ram 1500 Parts

Browse by Year

2010 Steering Knuckle 2009 Steering Knuckle 2008 Steering Knuckle 2007 Steering Knuckle 2006 Steering Knuckle 2005 Steering Knuckle 2004 Steering Knuckle 2003 Steering Knuckle 2002 Steering Knuckle 2001 Steering Knuckle 1999 Steering Knuckle 1998 Steering Knuckle 1997 Steering Knuckle 1996 Steering Knuckle 1995 Steering Knuckle 1994 Steering Knuckle