×
- Live Chat
- 1-888-511-3595
My Garage
My Account
Cart
Genuine Dodge Ram 2500 Rocker Arm
Engine Rocker Arm- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
17 Rocker Arms found
Dodge Ram 2500 Engine Intake Rocker Arm
Part Number: 5011431AB$166.52 MSRP: $253.00You Save: $86.48 (35%)
Dodge Ram 2500 Engine Rocker Arm Kit
Part Number: 53020742AB$28.39 MSRP: $42.70You Save: $14.31 (34%)
Dodge Ram 2500 Engine Intake Rocker Arm
Part Number: 53021552AA$139.75 MSRP: $210.00You Save: $70.25 (34%)
Dodge Ram 2500 Engine Intake Rocker Arm
Part Number: 68060343AA$139.75 MSRP: $210.00You Save: $70.25 (34%)
Dodge Ram 2500 Rocker Arm
Rocker Arm plays an important function in the Dodge Ram 2500 vehicles particularly in the valvetrain where motion is transferred from the pushrod to the intake and exhaust valve. Usual material used in manufacturing the Rocker Arm includes stamped steel or aluminum, and its function is to translate the movement of the pushrod in the vertical direction into the right amount of force required to act upon the valves. Aluminum is used in high RPM applications where it provides lightweight whereas cast iron or forged carbon steel is used in diesel engines for better strength and toughness. There are various types of Rocker Arms for Dodge Ram 2500 models but it may comprise of both the standard and roller rockers. They incorporate needle bearings such that take minimal effort to wear, and therefore are suitable for overhead valve and overhead camshaft engines. Another element is a rocker ratio that various from 1.5:1 to 1.8:1 in today's engines as it boosts the camshaft lift. Better fulcrum bearings are also observed on the engines with Higher RPM in order to cope with the stress it puts on the Rocker Arm of Dodge Ram 2500 vehicles and to increase its life expectancy.
Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Dodge Ram 2500 Rocker Arm at great affordable prices. Moreover, all genuine Dodge Ram 2500 Rocker Arm come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.
Dodge Ram 2500 Rocker Arm Parts Questions & Experts Answers
- Q: How to disassemble and inspect rocker arms and pushrods in diesel engine on Dodge Ram 2500?A: Disconnect the wires from the batteries at their negative terminals. Then remove the valve cover. Mark and detach the rocker arm/pedestal assemblies. Mark and take off crossheads. Pin down rocker arm sockets before raising them out of cylinder head. Mark and remove pushrods. Remove, clean with solvent, and disassemble rocker arms, pedestals, and shafts parts. Check for debris by blowing through oil passages. Get each rocker shaft bearing surface inspected for replacement if necessary.Measure each inside diameter of rocker arm bore against each outside diameter of rocker shaft and replace if worn too much.Check for cracks and scoring on all pushrod balls and ball seats, replacing any that are damaged.Look for damage or excessive wear on all crossheads in which case those affected should be replaced.Place the pushrods into position lubricate valve tips then put in place crossheads.Re-lubricate the bores , rockershafts then recapitulate the assembly of rockershaft/rockerarm/pedestal.Ensure lubrication of both crossheads as well as those sockets receiving a pushrod are done then fix a set of rockerarm/pedestal.The process ends by checking valve clearance.Installation of valve cover here may take place where it is not already installed.
