×
- Live Chat
- 1-888-511-3595
My Garage
My Account
Cart
Genuine Dodge Ram 3500 Fuel Filter
Gas Filter- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
16 Fuel Filters found
Dodge Ram 3500 Fuel Filter
The Fuel Filter is an essential part of Dodge Ram 3500 vehicles as it helps to protect the engine from clogging with dirt, debris and rust coming from the fuel line. This component usually incorporates cartridges that are made from pleated filtering paper to filter out bearer of contaminants to enable clean fuel to reach the engine. This is especially necessary for DT/Nav customer trucks such as Dodge Ram 3500 so as to avoid normal wear and possible failure of fuel machinery. In the different models of Dodge Ram 3500, years of usage have seen fuel filters being implemented in different designs such as bowl type diesel fuel filters that collect water to be drained out in order to protect the fuel system. Such filters may also contain additional elements such as water sensors and fuel heaters in order to provide improved operation in the cold. Knowing and practicing the Dodge Ram 3500 Fuel Filter maintenance program is very crucial in getting the most out of the automotive vehicle in terms of performance and its durability.
Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Dodge Ram 3500 Fuel Filter at great affordable prices. Moreover, all genuine Dodge Ram 3500 Fuel Filter come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.
Dodge Ram 3500 Fuel Filter Parts Questions & Experts Answers
- Q: How to drain and replace the fuel filter in a diesel engine on Dodge Ram 3500?A: The diesel engine fuel filter incorporates a water separator that removes and traps water in the fuel. This water must be drained from the filter at the specified intervals or when the Water In Fuel (WIF) light is on. Place a small container under the filter drain tube (diesel fuel can damage asphalt paving). For 2009 models, with the engine off, rotate the drain valve one turn counter-clockwise. Allow the water and contaminated fuel to drain out. Repeat the procedure until clean fuel flows from the filter drain tube, then place the drain valve in the closed position. For 2010 and later models, turn the drain valve knob 1/4-turn counterclockwise and unscrew the filter housing cover 1/2 turn. Allow the water and contaminated fuel to drain for two minutes, then close the drain valve and tighten the filter housing cover. Remove the container and dispose of the fuel/water mixture properly. If more than a couple of ounces had to be drained to remove any accumulated water, the fuel system may have to be primed for the engine to start. FUEL FILTER REPLACEMENT: At the specified intervals, the fuel filter element (which incorporates a water separator) should be replaced with a new one. Raise the vehicle and support it securely on jack stands. Remove the left front wheel and the fender splash shield. Drain the filter into a container and dispose of the fuel safely. Attach a hose extension to avoid spillage. Loosen the filter slightly to speed draining. For 2009 models, disconnect the Water In Fuel (WIF) harness connector, the drain hose, and extension hose from the drain valve. Use an oil filter wrench to rotate the bottom portion (canister filter) from the fuel filter assembly. Spin the fuel filter by hand from the fuel filter/canister assembly and set it aside. Remove the secondary fuel filter screen from the fuel filter assembly. Release the quick-connect fuel line fitting from the fuel filter assembly. Unscrew the line fitting from the fuel filter assembly and remove the fuel line along with the O-ring and filter screen. Clean the fuel filter screen and replace the O-ring with a new one. Installation is the reverse of removal. Use a new filter cartridge in the fuel filter assembly and a new O-ring in the fuel line. Turn the key to the On position, allowing the fuel pump to prime the system. Repeat this a few times until the engine starts. Run the engine and check for leaks. For 2010 and later models, clean all of the debris from the area of the fuel filter lid. Use a ratchet and socket to remove the fuel filter lid, then discard the O-ring from the canister. Remove the fuel filter element. Wipe out the interior of the canister but don't use any harsh chemicals such as brake cleaner. Install the new filter element. Lubricate the new O-ring with clean engine oil and install it on the canister. Replace the lid and tighten it to the torque. Turn the key to the On position, then briefly turn it to Start. This will allow the fuel pump to run for 25 seconds and should prime the system. If the vehicle doesn't start, repeat the procedure.
