How to Remove and Install the Intake Air Temperature Sensor on Jeep Liberty?

The intake manifold temperature sensor is a thermistor that changes resistance with temperature. On 2.4L four-cylinder engines, it is located on the rear lower part of the intake manifold. For 2007 and earlier Liberty models, disconnect the electrical connector and remove the sensor mounting bolts to remove it. For Nitro and 2008 and later Liberty models, it is installed into the rubber air intake tube near the throttle body or beginning of the air filter housing. Disconnect the electrical connector and remove the sensor by turning it counterclockwise and pulling it out. Installation is the reverse of removal.

Genuine Jeep Liberty Intake Manifold Temperature Sensor

Air Intake Temperature Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 Intake Manifold Temperature Sensors found

View related parts
Jeep Liberty Sensor-Air Temperature
Part Number: 56028364AA
$27.46 MSRP: $40.75
You Save: $13.29 (33%)
ADD TO CART
Product Specifications
- Other Name: Sensor Air Temperature
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2002-2004 Jeep Liberty | Limited Edition 2WD, Limited Edition 4WD, Renegade 2WD, Renegade 4WD, Sport 2WD, Sport 4WD | 4 Cyl 2.4L, 6 Cyl 3.7L
View related parts
Jeep Liberty Sensor-Charge Air Temp
Part Number: 4606487AB
$63.83 MSRP: $96.10
You Save: $32.27 (34%)
ADD TO CART
Product Specifications
- Other Name: Sensor Charge Air Temp
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2004-2012 Jeep Liberty | Limited Edition 2WD, Limited Edition 4WD, Limited JET Edition 2WD, Limited JET Edition 4WD, Renegade 2WD, Renegade 4WD, Sport 2WD, Sport 4WD | 4 Cyl 2.4L, 6 Cyl 3.7L
View related parts
Jeep Liberty Sensor-Air Temperature
Part Number: 68031593AA
$204.59 MSRP: $310.00
You Save: $105.41 (34%)
ADD TO CART
Product Specifications
- Other Name: Sensor Air Temperature; Air Intake Temperature Sensor, Temperature Sensor
- Replaces: 5140331AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2010 Jeep Liberty
- 2005-2006 Jeep Liberty | Limited Edition 4WD, Sport 2WD, Sport 4WD | 4 Cyl 2.8L Diesel
View related parts
Jeep Liberty Sensor-Air Temperature
Part Number: 5140331AA
$204.59 MSRP: $310.00
You Save: $105.41 (34%)
ADD TO CART
Product Specifications
- Other Name: Sensor Air Temperature
- Replaced by: 68031593AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2005-2006 Jeep Liberty | Limited Edition 4WD, Sport 2WD, Sport 4WD | 4 Cyl 2.8L Diesel
View related parts
Jeep Liberty Air Temperature
Part Number: 5003734AA
Product Specifications
- Other Name: Sensor Air Temperature
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2002 Jeep Liberty | Sport 2WD, Sport 4WD
View related parts
Jeep Liberty Air Temperature
Part Number: 5093898AA
Product Specifications
- Other Name: Sensor Air Temperature
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2003-2004 Jeep Liberty | Sport 2WD, Sport 4WD

Jeep Liberty Intake Manifold Temperature Sensor

The Intake Manifold Temperature Sensor used in Jeep Liberty vehicle model is one of the most important devices when it comes to the burn procedure in an engine and overall performance. This information is then sent to the PCM where the fuel injector timing is altered so that the correct air/fuel ratio is maintained for different operations. That is why the Intake Manifold Temperature Sensors may vary in their style at different Jeep Liberty models, and some of them may be tuned to definite air flow rates. Damaged or low-quality Intake Manifold Temperature Sensor can cause problems such as hesitation during acceleration or the vehicle stalling, which is normally attributed to the wrong air/fuel mixture. A check of air intake system is very important so that there is no mix up of unaccounted air and thus enable the Jeep Liberty to work efficiently.

Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Jeep Liberty Intake Manifold Temperature Sensor at great affordable prices. Moreover, all genuine Jeep Liberty Intake Manifold Temperature Sensor come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.

Jeep Liberty Intake Manifold Temperature Sensor Parts Questions & Experts Answers

Sensor-Air Temperature
56028364AA
Q: How to Remove and Install the Intake Air Temperature Sensor on Jeep Liberty?
A: The intake manifold temperature sensor is a thermistor that changes resistance with temperature. On 2.4L four-cylinder engines, it is located on the rear lower part of the intake manifold. For 2007 and earlier Liberty models, disconnect the electrical connector and remove the sensor mounting bolts to remove it. For Nitro and 2008 and later Liberty models, it is installed into the rubber air intake tube near the throttle body or beginning of the air filter housing. Disconnect the electrical connector and remove the sensor by turning it counterclockwise and pulling it out. Installation is the reverse of removal.