Chrysler 4782873AB Bar-Rear Suspension

You can Select Your Vehicle to check if 4782873AB fits your vehicle.

To perform this procedure, ensure you have a transmission jack or equivalent and additional help from an assistant. Start by disconnecting the cable from the negative battery terminal. Then, raise the rear of the vehicle, support it securely on jackstands under the frame rails, and remove the wheel. Next, remove the rear exhaust system and disconnect the driveshaft from the rear differential. Separate and detach the parking brake equalizer from the front parking brake cable and remove the bracket holding the parking brake cable to the subframe. Mark the subframe in relation to the chassis at all four mounting locations to maintain rear wheel alignment. Support the spring link with a floor jack and wood block, and remove the shock absorber lower mounting fasteners, slowly lowering the floor jack supporting the spring link. Remove the brake calipers and secure them to prevent damage to brake hoses during subframe lowering. Disconnect and remove the ABS wheel speed harnesses from the chassis. Place a transmission jack under the differential and secure it. Remove the fuel filler neck. With the transmission jack in place, remove all four subframe bolts and slowly lower the subframe enough to separate the driveshaft from the differential. Continue lowering the subframe to gain access to the sway bar link bushing kit retainers. Stabilize the subframe with additional jackstands. Remove the sway bar link bushing kit bracket fasteners, brackets, and bushings. Clean the sway bar link bushing kit and inspect the bushings and links for wear or damage. Replace any damaged components. During installation, ensure proper alignment of the subframe and coil spring, guide the shock absorbers and driveshaft into place, use correct bolt lengths, reinstall all components, simulate normal ride height, and tighten all fasteners. Finally, have the wheel alignment checked and adjusted if necessary.

The following involves the use of a transmission jack or any other equivalent and it is advised that there should be an assistant during this procedure. First, get the cable out of the negative terminal of the battery. First, you need to turn the wheel lug nuts and raise the rear part of your vehicle with the help of jack, put jackstands under the frame rails and only then you can take off the wheel. Then, it is necessary to take out the rear part of the exhaust and to separate the drive shaft from the rear differential. Disconnect the subframe side parking brake equalizer from parking brake's front cable which is above the rear differential and then undo the bracket fastening parking brake cable to the subframe. Against the chassis, mark the subframe on all the four points of mounting. Place a floor jack under the spring link and insert a wood block under the floor jack to avoid the spring from compressing back, then, remove the nuts for the lower mounting of the shock absorber and slowly lower the floor jack until the spring is fully stretched. Lose the brake calipers and put them out of the way not to touch the brake hoses when lowering the subframe, and take off and unplug the ABS wheel speed harnesses from the chassis. While securing the rear sway bar to the transmission jack do not secure the differential along with it. Slide a transmission jack under the differential and tighten it and finally unbolt the fuel filler neck. With the transmission jack in position loose all the four subframe bolts then slowly lower the subframe in a way that the drive shaft would be detached from the differential until there is adequate space to work on the sway bar brackets. Use more jackstands or their equivalent to support the subframe and suspension assembly and then unbolt the retainers for the sway bar bracket; remove the bar and the brackets and note the position of the slits on the bar when removing the bushings. Wipe out the area where the bushings rest on the sway bar and check the bushings for signs of wear and or damages such as cracks, tears or deterioration and if you find any of these replace them. Lift the car and take off the sway bar links; visually check the ones you removed for signs of wear or damage; if there are any, replace them with new ones. Most of these procedures are carried out with equal measures as those that were followed during removal, the only major consideration being that before raising the subframe into final position, the lower shock absorber fasteners are to be placed in appropriate positions but not yet tightened up. During raising of subframe, check that coil spring and insulators are correctly positioned in the upper position and align the subframe with the previous markings. As the subframe is being positioned the driveshaft has to be connected to the rear differential and the top of the shock absorbers have to go under the chassis, this is done at the final moments when the subframe is being lowered into position. The bolts for fixing the subframe are of two different sizes; the longer bolts are fixed at the rear side and the shorter bolts fixed at the front side. Replace brake; fuel tank; driveline; exhaust parts; lift the spring link with a floor jack to set it close to normal ride height then final tighten lower shock absorber and sway bar link mounting bolts. Tighten all suspension fasteners to the specified torque and have the alignment of the wheels checked and corrected if needed.

Disconnect the cable from the negative battery terminal.

Check each stabilizer link for signs of excessive wear and replace them as necessary.

Remove the lower nut from the stabilizer bar link and separate it from the bar.

Remove the stabilizer bar bracket fasteners and remove the brackets.

A transmission jack or equivalent and additional help from an assistant.

Remove the stabilizer bar bracket fasteners and remove the brackets.