Make sure this part fits

Chrysler 5136021AE Fuel Pump/Level Unit Module

2006-2008 Chrysler 300 5136021AE

Customer Questions & Expert Answers (10)
Mopar 5136021AE Fuel Pump/Level Unit Module
  • Part Description
    Module-Fuel Pump/Level Unit
  • Replaces
    5136021AC, 5136021AB, 5136021AD
  • Manufacturer
    Mopar
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
$168.07 MSRP: $250.00
You Save: $81.93 (33%)
Currently Unavailable

Due to manufacturer supply shortage, this item isn’t currently available for ordering.

  • Related Parts
  • Product Specifications
  • Vehicle Fitment
  • Customer Questions & Expert Answers
  • Product Specifications

    BrandGenuine Chrysler
    Manufacturer Part Number5136021AE
    Part DescriptionModule-Fuel Pump/Level Unit
    Other NamesFuel Pump
    Item Dimensions7.8 x 11.3 x 14.4 inches
    Item Weight3.20 Pounds
    ConditionNew
    Fitment TypeDirect Replacement
    Replaces5136021AC, 5136021AB, 5136021AD
    ManufacturerMopar
    SKU5136021AE
    WarrantyThis genuine Mopar part is guaranteed by Mopar's factory warranty.
    Shipping & ReturnShipping Policy Return Policy
    Warning: California’s Proposition 65
  • Vehicle Fitment

    Year Make Model Engine Important vehicle option details
    2006-2008 Chrysler 3006 Cyl 2.7L, 6 Cyl 3.5L, 8 Cyl 5.7LBase RWD, C AWD, C RWD, LX RWD, Limited AWD, Limited RWD, Touring AWD, Touring RWD
  • Customer Questions & Expert Answers

    Q:
    Will this fit my truck? Posted by MoparPartsGiant Specialist
    A:
    You can Select Your Vehicle to check if 5136021AE fits your vehicle.
    Posted by MoparPartsGiant Specialist
    Q:
    How to Remove and Install the Fuel Pump/Fuel Level Sensor and the Fuel Filter/Fuel Pressure Regulator on Dodge Charger? Posted by Customer
    A:
    Relieve fuel system pressure. Disconnect cable from negative battery terminal. Drain fuel tank to under 5/8-full. Remove rear seat cushion. Pull back foam pad covering fuel pump/fuel level sensor module. Pull off plastic access cover. Disconnect electrical connector from terminal on top of fuel pump/fuel level sensor module. Clean area surrounding mounting flange. Tap lock-ring counterclockwise with hammer and brass drift. Note square tab on edge of mounting flange. Disconnect two electrical connectors for fuel level sensors and fuel pump. Disconnect fuel supply line fitting from outlet pipe. Disconnect two return lines from fuel pump module. Lift up mounting flange and remove fuel filter/fuel pressure regulator/fuel level sensor module.
    Posted by MoparPartsGiant Specialist
    Q:
    How do you replace the right fuel level sensor, fuel pressure regulator, and fuel filter module for the 2008 Chrysler 300? Posted by Customer
    A:
    Remove the module and detach the fuel level sensor. Cut the wire ties and disconnect the ground wires. Remove the fuel level sensor. If you're only replacing the fuel pressure regulator, you're done. To remove the regulator from the fuel filter module, pull out the retaining clip. Check the condition of the regulator's O-rings. If you're replacing the fuel filter module, remove the ground ring and install it correctly in the new module. Finally, installation is the reverse of removal.
    Posted by MoparPartsGiant Specialist
    Q:
    How can a fuel pressure test be performed for the 2007 Chrysler 300? Posted by Customer
    A:
    To perform a fuel pressure test, relieve the fuel system pressure and connect a fuel pressure gauge to the fuel supply line. Start the engine and check the pressure on the gauge. If the pressure is not within specifications, check for a restriction in the fuel system or replace the fuel pressure regulator.
    Posted by MoparPartsGiant Specialist
    Q:
    Where is the fuel pump located for the 2007 Dodge Charger? Posted by Customer
    A:
    The fuel pump is located inside the fuel tank.
    Posted by MoparPartsGiant Specialist
    See expert answers on similar Fuel Pump
    Q:
    What is the procedure for draining the fuel tank to a certain level for the 2008 Chrysler 300? Posted by Customer
    A:
    To drain the fuel tank to under 5/8-full:Route a hose through the fuel filler neck hose.Use a hard nylon tube with a 30-degree cut on the end to push open the check valve in the fuel filler neck.
    Posted by MoparPartsGiant Specialist
    See expert answers on similar Fuel Pump
    Q:
    How do you replace the right fuel level sensor, fuel pressure regulator, and fuel filter module for the 2010 Dodge Charger? Posted by Customer
    A:
    Remove the module and detach the fuel level sensor. Cut the wire ties and disconnect the ground wires. Remove the fuel level sensor. If you're only replacing the fuel pressure regulator, you're done. To remove the regulator from the fuel filter module, pull out the retaining clip. Check the condition of the regulator's O-rings. If you're replacing the fuel filter module, remove the ground ring and install it correctly in the new module. Finally, installation is the reverse of removal.
    Posted by MoparPartsGiant Specialist
    See expert answers on similar Fuel Pump
    Q:
    What should be done if the pump runs continuously for the 2007 Dodge Magnum? Posted by Customer
    A:
    If the pump runs continuously, the PCM may be defective.
    Posted by MoparPartsGiant Specialist
    Q:
    How do you replace the left fuel level sensor and fuel pump module for the 2008 Dodge Magnum? Posted by Customer
    A:
    Start by removing the module. Then, carefully cut the wiring harness clip and disconnect the fuel level sensor wires. Loosen the two retaining clips and pull out the fuel level sensor. You can replace either the fuel level sensor unit or the fuel pump module.
    Posted by MoparPartsGiant Specialist
    See expert answers on similar Fuel Pump
    Q:
    How do you proceed with lifting the fuel pump/fuel level sensor module for removal for the 2008 Dodge Magnum? Posted by Customer
    A:
    To lift the fuel pump/fuel level sensor module for removal:Lift up the mounting flange for the module.Disconnect the two electrical connectors for the fuel level sensors and the fuel pump.If the lower half of the module is still submerged in gasoline, drain the remaining fuel from the left fuel tank.
    Posted by MoparPartsGiant Specialist
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

Genuine Mopar Part 5136021AE, the Right Choice

To ensure reliability, purchase Mopar part # 5136021AE Fuel Pump/Level Unit Module. It is sometimes referred to as Chrysler Fuel Pump, Chrysler Fuel Sending Unit. For Mopar owners with dreams of keeping their vehicles running in prime condition, choosing OEM parts is a smart decision. Meticulously crafted, these parts follow strict factory specifications and are manufactured in top-notch facilities with advanced technologies. Furthermore, they undergo rigorous testing to ensure durability and safety, making them a reliable choice for Mopar owners. This part fits specific Chrysler 300 models.

MoparPartsGiant.com is a leading supplier of genuine Mopar parts and accessories such as Mopar 5136021AE Fuel Pump/Level Unit Module. Wondering where to find exceptional quality and affordable OEM Mopar parts? You have already come to the right place. Our website boasts a huge selection of genuine Mopar parts at the most economical prices possible. What's more, all parts come with a manufacturer's warranty. For detailed Chrysler parts information, click here.

Why choose Mopar Parts Giant

  • Dedicated Service

    Your complete satisfaction is our #1 goal

  • Lowest Prices

    Best deals on genuine OE parts from dealerships

  • Fast Delivery

    Orders are processed and delivered promptly