Make sure this part fits

Chrysler 5136022AF Fuel Pump/Level Unit Module

2008-2009 Chrysler 300 5136022AF

Customer Questions & Expert Answers (13)
Mopar 5136022AF Fuel Pump/Level Unit Module
  • Part Description
    Module-Fuel Pump/Level Unit
  • Replaced By
    5136022AL
  • Manufacturer
    Mopar
Make sure this part fits
$408.10 MSRP: $623.00
You Save: $214.90 (35%)
1
ADD TO CART
  • Related Parts
  • Product Specifications
  • Vehicle Fitment
  • Customer Questions & Expert Answers
  • Product Specifications

    BrandGenuine Chrysler
    Manufacturer Part Number5136022AF
    Part DescriptionModule-Fuel Pump/Level Unit
    Item Dimensions13.3 x 10.1 x 8.4 inches
    Item Weight3.30 Pounds
    ConditionNew
    Fitment TypeDirect Replacement
    ManufacturerMopar
    SKU5136022AF
    WarrantyThis genuine Mopar part is guaranteed by Mopar's factory warranty.
    Shipping & ReturnShipping Policy Return Policy
    Warning: California’s Proposition 65
  • Vehicle Fitment

    Year Make Model Engine Important vehicle option details
    2008-2009 Chrysler 3006 Cyl 2.7L, 6 Cyl 3.5L, 8 Cyl 5.7LC AWD, C RWD, Limited AWD, Limited RWD, LX RWD, Touring AWD, Touring RWD
  • Customer Questions & Expert Answers

    Q:
    Will this fit my truck? Posted by MoparPartsGiant Specialist
    A:
    You can Select Your Vehicle to check if 5136022AF fits your vehicle.
    Posted by MoparPartsGiant Specialist
    Q:
    How Do You Remove the Fuel Pump/Fuel Level Sensor/Fuel Filter on Dodge Challenger? Posted by Customer
    A:
    A fuel pump/fuel level sensor module, also known as the main fuel pump module, is located in the left compartment of the fuel tank. It includes the fuel pump inlet strainer, pump, fuel level sensor, and fuel pressure regulator. The module is removed as a complete assembly, and most replacement modules come with all these components. The auxiliary fuel pump module is located in the right side of the fuel tank and includes the main fuel filter and fuel pressure regulator. On earlier models, the fuel pressure regulator can be replaced separately, but on later models, neither component can be replaced separately. To remove the fuel pump/fuel level sensor module, the fuel system pressure must be relieved, the negative battery terminal cable must be disconnected, and the fuel tank must be drained to under 5/8-full. The rear seat cushion is removed, and the foam pad covering the module is pulled back. The plastic access cover is carefully lifted off, and the electrical connector is disconnected. The area surrounding the mounting flange is cleaned, and the lock-ring is loosened and unscrewed. The module is lifted up, and the electrical connectors and fuel supply line fitting are disconnected. The residual fuel is drained, and the module is carefully removed from the fuel tank. The installation is the reverse of removal, and after installation, the fuel system is primed by turning the ignition switch to On without operating the starter.
    Posted by MoparPartsGiant Specialist
    Q:
    How do you replace the right fuel level sensor, fuel pressure regulator, and fuel filter module for the 2008 Dodge Magnum? Posted by Customer
    A:
    Remove the module and detach the fuel level sensor. Cut the wire ties and disconnect the ground wires. Remove the fuel level sensor. If you're only replacing the fuel pressure regulator, you're done. To remove the regulator from the fuel filter module, pull out the retaining clip. Check the condition of the regulator's O-rings. If you're replacing the fuel filter module, remove the ground ring and install it correctly in the new module. Finally, installation is the reverse of removal.
    Posted by MoparPartsGiant Specialist
    See expert answers on similar Fuel Pump
    Q:
    How do you replace the right fuel level sensor, fuel pressure regulator, and fuel filter module for the 2009 Chrysler 300? Posted by Customer
    A:
    Remove the module and detach the fuel level sensor. Cut the wire ties and disconnect the ground wires. Remove the fuel level sensor. If you're only replacing the fuel pressure regulator, you're done. To remove the regulator from the fuel filter module, pull out the retaining clip. Check the condition of the regulator's O-rings. If you're replacing the fuel filter module, remove the ground ring and install it correctly in the new module. Finally, installation is the reverse of removal.
    Posted by MoparPartsGiant Specialist
    Q:
    How do you replace the left fuel level sensor and fuel pump module for the 2013 Dodge Challenger? Posted by Customer
    A:
    Start by removing the module. Carefully cut the wiring harness clip and disengage the fuel level sensor wires from the clip. Then, loosen the two retaining clips and pull the fuel level sensor out of the fuel pump module. After installation, turn the ignition switch to On to activate the fuel pump and build up fuel pressure in the fuel lines.
    Posted by MoparPartsGiant Specialist
    See expert answers on similar Fuel Pump
    Q:
    How can the fuel pump be heard for the 2005 Chrysler 300? Posted by Customer
    A:
    The fuel pump can be heard when the ignition key is turned to ON.
    Posted by MoparPartsGiant Specialist
    Q:
    How do you disconnect the electrical connector from the terminal on top of the fuel pump/fuel level sensor module for the 2009 Chrysler 300? Posted by Customer
    A:
    To disconnect the electrical connector from the terminal on top of the module:Depress the release tab on the connector.Place the harness safely out of the way.
    Posted by MoparPartsGiant Specialist
    See expert answers on similar Fuel Pump
    Q:
    How do you replace the right fuel level sensor, fuel pressure regulator, and fuel filter module for the 2006 Dodge Charger? Posted by Customer
    A:
    Remove the module and detach the fuel level sensor. Cut the wire ties and disconnect the ground wires. Remove the fuel level sensor. If you're only replacing the fuel pressure regulator, you're done. To remove the regulator from the fuel filter module, pull out the retaining clip. Check the condition of the regulator's O-rings. If you're replacing the fuel filter module, remove the ground ring and install it correctly in the new module. Finally, installation is the reverse of removal.
    Posted by MoparPartsGiant Specialist
    See expert answers on similar Fuel Pump
    Q:
    What steps should be taken during reinstallation for the 2006 Dodge Charger? Posted by Customer
    A:
    During reinstallation:Ensure that the flange orientation is correct based on the square tab on its circumference.Carefully reattach the electrical connectors and the fuel lines.Follow the reverse order of removal for all components.
    Posted by MoparPartsGiant Specialist
    See expert answers on similar Fuel Pump
    Q:
    How can the fuel pump be heard for the 2006 Dodge Charger? Posted by Customer
    A:
    The fuel pump can be heard when the ignition key is turned to ON.
    Posted by MoparPartsGiant Specialist
    See expert answers on similar Fuel Pump
    Q:
    How should you handle removing the fuel filter/fuel pressure regulator/fuel level sensor module for the 2005 Dodge Magnum? Posted by Customer
    A:
    To remove the fuel filter/fuel pressure regulator/fuel level sensor module:Lift up the mounting flange for the module.Carefully remove the module from the fuel tank, ensuring not to damage the electrical harness or fuel return lines.
    Posted by MoparPartsGiant Specialist
    Q:
    What should be done if the pump runs continuously for the 2008 Dodge Magnum? Posted by Customer
    A:
    If the pump runs continuously, the PCM may be defective.
    Posted by MoparPartsGiant Specialist
    Q:
    what is the difference between part numbers 5136022AF and 5136021AF Posted by Customer: 2009 Dodge Charger
    A:
    5136021AF SUPERSEEDS TO 68102700AC MAIN FUEL PUMP, BE ADVISED ITS ON BACK ORDER. 5136022AF SUPERSEEDS TO 05136022AK DOES NOT SHOW IT APPLIES TO VIN NUMBER PROVIDED.
    Posted by MoparPartsGiant Specialist 10/2/2022
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

Genuine Mopar Part 5136022AF, the Right Choice

To ensure reliability, purchase Mopar part # 5136022AF Fuel Pump/Level Unit Module. It is sometimes referred to as Chrysler Fuel Pump, Chrysler Fuel Sending Unit. For Mopar owners with dreams of keeping their vehicles running in prime condition, choosing OEM parts is a smart decision. Meticulously crafted, these parts follow strict factory specifications and are manufactured in top-notch facilities with advanced technologies. Furthermore, they undergo rigorous testing to ensure durability and safety, making them a reliable choice for Mopar owners. This part fits specific Chrysler 300 models.

MoparPartsGiant.com is a leading supplier of genuine Mopar parts and accessories such as Mopar 5136022AF Fuel Pump/Level Unit Module. Wondering where to find exceptional quality and affordable OEM Mopar parts? You have already come to the right place. Our website boasts a huge selection of genuine Mopar parts at the most economical prices possible. What's more, all parts come with a manufacturer's warranty. For detailed Chrysler parts information, click here.

Why choose Mopar Parts Giant

  • Dedicated Service

    Your complete satisfaction is our #1 goal

  • Lowest Prices

    Best deals on genuine OE parts from dealerships

  • Fast Delivery

    Orders are processed and delivered promptly