Jeep L0009145 Bulb

You can Select Your Vehicle to check if L0009145 fits your vehicle.

Vehicle exterior lights include front park/turn signal lights, inner and outer front parking lights, front side marker lights, fog lights, center high-mounted brake lights, tail lights, and license plate lights. To replace the fog light bulb, raise the vehicle, remove the splash shield, disconnect the connector, remove the bulb holder, and install the new bulb. The center brake lights cannot have individual bulbs replaced. To replace tail light bulbs, open the trunk, disconnect the connector, remove the taillight assembly, and replace the bulb. The license plate light bulb is in the rear bumper cover, remove the housing screws, the bulb socket, and replace the bulb. The reading light bulbs require prying off the lens, removing the housing, and replacing the bulb. The vanity light bulbs can be removed by prying off the lens and sliding out the bulb, then installing the new bulb. The door courtesy lights are in the front door trim panels, pry the lens out, pull down the light/lens assembly, remove the bulb, and install the new bulb. The rear reading lights require prying out the lens, removing the bulb, and installing the new bulb.

To replace the fog light the following processes have to be followed, Loosen the front wheel lug nuts and lift the vehicle; remove the wheel. Next, unbolt the fenderwell splash shield and swing it to the side for fog light access as shown in fig 2. Stuck the bulb electrical connector, and turn the bulb holder anticlockwise and pull out from the housing. Instead of replacing the bulb separately from the holder, both are replaced together with much attention given not to touch the bulb surface with fingers so as to avoid making it hot. For the tail light, using a Torx head screw driver, remove the screw that fastens the housing to the quarter panel after which the housing has to be pulled out and to put in a new bulb, turn the holder anti clock wise. To replace the license plate light, one will need to unscrew the Torx-head screws, disconnect the assembly and replace the bulb which will be done by pulling it out vertically. For the back-up light, simple unscrew or pry the housing out, then turn the bulb holder counter clockwise and pull the bulb out. The high-mounted brake light can be replaced very easily; one has to pry off the trim cover, remove the lens and then pull the bulbs right out. To get to the instrument cluster lights it is necessary to pull out the cluster, then turn the bulb holder anti-clockwise. Courtesy/reading light Just pull the lens of this product from the housing and then you can remove the bulb from the spring clips. The dome light what requires is little more effort to pry out the left side of the lens and then pull the bulb directly out. Lastly for the cargo light, the access door and jack bag needs to be taken off, light housing to be disconnected, the bulb is to be pulled straight out and one has to push the new bulb in the lens holder before finally fixing the lens holder.

First for the replacement of the exterior light bulbs take out the front park and turn signal bulb, first by unscrewing the headlight housing, disconnecting the electrical connectors and then removing the bulb socket by rotating anti clockwise. To replace a bad bulb, carefully twist the bulb and pull it up and out, insert new bulb and repeat the procedure in the reverse order. For front fog light bulbs: lift the vehicle, snap off the electrical connector, turn the socket anti-clockwise to unbolt it, and then replace the bulb/socket assembly and do not touch the bulb surface. For the center high-mounted brake light bulb, first, there will be two or three screws that hold it in place, unscrew it, next you take out the whole assembly and then remove the bulb from it. For tail light bulbs the retaining screws should be withdrawn, then the assembly should be turned in order to unlock it, the electrical connector should be disconnected and finally the bulb socket should be removed by pressing both tabs. Remove the bulb by pulling it directly upwards and the installation is done in the same manner. For license plate light bulbs, the screws which hold it must be undone, and the assembly pulled down so that the bulb can be pulled out of the socket. Starting with the interior light bulbs, the first one is the instrument cluster These are removed, rotated anticlockwise and then replaced with a new one by rotating the bulb socket in the clockwise direction. For courtesy lights unscrew the light from the door trim, pull the electrical connector, unscrew the lens and change the bulb. For dome/cargo lights you get to the profile of the light and pry off the lens you thereafter remove the bulb and repeat the process in order to install the bulb. For the glove box light, first, open the glove box then push the switch through the hole then remove the electrical connector more the bulb from the switch. To change the liftgate light bulb, one has to gently pull the lens of the trim panel to be able to remove the bulb and then just do it in reverse. For reading lights using lens, the lens should be removed by twisting it in anti-clockwise direction to unclip the bulb from the reflector while installation is in reverse procedure. Last, to install the vanity lights pry off the lens, remove the bulb and follow the same process in reverse to the process just described above.

To replace they front park/turn signal/sidemarker light bulbs one has to turn on the engine and the wheels to make space or remove the wheel by loosing the nuts then raising the car. Inside the wheel housing you would see an access panel, you would seize the electrical connector and pull it off by unlocking the lock first, then you would rotate counter clockwise the bulb socket. Twist the bulb clockwise and anti-clockwise and then replace it with a new one by inserting it into the socket until it fits in properly in an opposite manner as used during removal. For fog light bulbs, the electrical connector can be released by pulling the locking tab, the socket should then be unscrewed anticlockwise and the bulb should be pulled out and the same process should be reversed when replacing a bulb. To change the center high mounted brake light bulb, the housing has to be unscrewed and the electrical connector disconnected, then the bulb socket has to be rotated and pulled out together with the bulb, after which a new one has to be inserted by pushing it in until it clicks back in place. The rear taillight assembly have four bulbs; to change it one has to open the liftgate then remove the push pin fasteners, then disconnect the electrical connector, and finally remove the bulb socket plate by unscrewing it, the desired bulb can then be pulled out and for installation, a new one is inserted by pushing it up to the desired position. For the license plate light bulb, unscrew the two small screws to come out the housing, then rotate the socket one turn clockwise to remove it, then the bulb can be removed by pulling it straight up and the new one has to be inserted in the same manner until it engages into the socket. For interior lights the switch housing should be carefully unclipped, electrical connectors shall be disconnected, lens shall be removed, the bulb has to be gently pulled down and a new one has to be inserted by fixing it in the appropriate terminals while reversing the procedure. Replacement of vanity light bulbs involves usually detaching the lens from the visor, then using pliers to extract the bulb and put in a new one in the same manner till it fits properly. For the dome light, pry down the left side of the lens and carefully pull out the bulb in a straight down motion, to replace it, place the new bulb in an up-direction until it clicked into position in the reverse procedure. For replacing the illumination bulbs of front and rear heater/air conditioning control assembly, first remove these assemblies, then unscrew the bulb holders anti-clockwise and the bulbs can be replaced by fixing new ones in similar fashion by turning these holders clockwise. The housing has to be removed and the cover plate unscrewed in order to reach the bulb which is located in the instrument panel center bezel; to replace, pull the bulb out straight then push in a new one until you hear a click in reverse order. Last but not least for the glove box light bulb, the way to replace it involves pulling down the glove box and taking out the light bulb, after which the new one is fitted into the socket and pushed back to the required extent.

To replace they front park/turn signal/sidemarker light bulbs one has to turn on the engine and the wheels to make space or remove the wheel by loosing the nuts then raising the car. Inside the wheel housing you would see an access panel, you would seize the electrical connector and pull it off by unlocking the lock first, then you would rotate counter clockwise the bulb socket. Twist the bulb clockwise and anti-clockwise and then replace it with a new one by inserting it into the socket until it fits in properly in an opposite manner as used during removal. For fog light bulbs, the electrical connector can be released by pulling the locking tab, the socket should then be unscrewed anticlockwise and the bulb should be pulled out and the same process should be reversed when replacing a bulb. To change the center high mounted brake light bulb, the housing has to be unscrewed and the electrical connector disconnected, then the bulb socket has to be rotated and pulled out together with the bulb, after which a new one has to be inserted by pushing it in until it clicks back in place. The rear taillight assembly have four bulbs; to change it one has to open the liftgate then remove the push pin fasteners, then disconnect the electrical connector, and finally remove the bulb socket plate by unscrewing it, the desired bulb can then be pulled out and for installation, a new one is inserted by pushing it up to the desired position. For the license plate light bulb, unscrew the two small screws to come out the housing, then rotate the socket one turn clockwise to remove it, then the bulb can be removed by pulling it straight up and the new one has to be inserted in the same manner until it engages into the socket. For interior lights the switch housing should be carefully unclipped, electrical connectors shall be disconnected, lens shall be removed, the bulb has to be gently pulled down and a new one has to be inserted by fixing it in the appropriate terminals while reversing the procedure. Replacement of vanity light bulbs involves usually detaching the lens from the visor, then using pliers to extract the bulb and put in a new one in the same manner till it fits properly. For the dome light, pry down the left side of the lens and carefully pull out the bulb in a straight down motion, to replace it, place the new bulb in an up-direction until it clicked into position in the reverse procedure. For replacing the illumination bulbs of front and rear heater/air conditioning control assembly, first remove these assemblies, then unscrew the bulb holders anti-clockwise and the bulbs can be replaced by fixing new ones in similar fashion by turning these holders clockwise. The housing has to be removed and the cover plate unscrewed in order to reach the bulb which is located in the instrument panel center bezel; to replace, pull the bulb out straight then push in a new one until you hear a click in reverse order. Last but not least for the glove box light bulb, the way to replace it involves pulling down the glove box and taking out the light bulb, after which the new one is fitted into the socket and pushed back to the required extent.

Vehicle exterior lights include front park/turn signal lights, inner and outer front parking lights, front side marker lights, fog lights, center high-mounted brake lights, tail lights, and license plate lights. To replace the fog light bulb, raise the vehicle, remove the splash shield, disconnect the connector, remove the bulb holder, and install the new bulb. The center brake lights cannot have individual bulbs replaced. To replace tail light bulbs, open the trunk, disconnect the connector, remove the taillight assembly, and replace the bulb. The license plate light bulb is in the rear bumper cover, remove the housing screws, the bulb socket, and replace the bulb. The reading light bulbs require prying off the lens, removing the housing, and replacing the bulb. The vanity light bulbs can be removed by prying off the lens and sliding out the bulb, then installing the new bulb. The door courtesy lights are in the front door trim panels, pry the lens out, pull down the light/lens assembly, remove the bulb, and install the new bulb. The rear reading lights require prying out the lens, removing the bulb, and installing the new bulb.

Vehicle exterior lights include front park/turn signal lights, inner and outer front parking lights, front side marker lights, fog lights, center high-mounted brake lights, tail lights, and license plate lights. To replace the fog light bulb, raise the vehicle, remove the splash shield, disconnect the connector, remove the bulb holder, and install the new bulb. The center brake lights cannot have individual bulbs replaced. To replace tail light bulbs, open the trunk, disconnect the connector, remove the taillight assembly, and replace the bulb. The license plate light bulb is in the rear bumper cover, remove the housing screws, the bulb socket, and replace the bulb. The reading light bulbs require prying off the lens, removing the housing, and replacing the bulb. The vanity light bulbs can be removed by prying off the lens and sliding out the bulb, then installing the new bulb. The door courtesy lights are in the front door trim panels, pry the lens out, pull down the light/lens assembly, remove the bulb, and install the new bulb. The rear reading lights require prying out the lens, removing the bulb, and installing the new bulb.

For replacing the front turn signal/parking light/side marker light bulbs, remove the headlight housing as well as the bulb holder. After that, take out the old bulb and put in a new one. For the high-mounted brake light and cargo light bulbs, detach the housing while disconnecting its electrical connectors. Then you should twist and remove it from the bulb holder so that you can be able to pull out its old bulb and insert a new one. To replace fog lamp bulbs, unplug wiring from it turning counterclockwise to remove it from a hole in which it was placed. For license plate light bulbs, untwist and remove it off from its holder after that you can be able to pull out an old bulb and insert a new one for replacement purposes. Mirror mounted lights are LED lights; therefore replacing them involves fitting a new LED assembly if they become faulty. The rear fender lights need to be gently pushed or pulled out of their lens before being twisted off from their bulb holders allowing pulling out of an old bulb and inserting a new one instead. To change tailgate lights unscrew screws on this side of light lens so that you get chance of removing it from there with ease. This is how you take off an old bulb by twisting down its holder while installing another one in its place so far as your vehicle's taillight assembly is concerned. Bed storage bin Lightbulbs have their lens removed by taking such lens off by twisting around at its holder level;thereafter,you will be able to pull out an old bulb before fixing anewone in position.The dome light will require you push down the sides of this cover then detach all parts including these bulbs themselves using hands carefully.Insert anewbulb of suitable size properly back into place.To replace glove box lighting facility,it should simply be slid straight direction for removal then another piece inserted into opposite groove whereit cameoff.These reading lamps need to have the sides pried open and then slide it forward until you can be able to remove one end from them.Put in a LED bulb of same size or wattage as that which is being replaced.As forthese vanity light bulbs, the lens has to be pried off from the top part of light assembly so that afterthat you can pull out its old bulb gently and replace it with anewone.Such light fixtures are devised in such a way that their covers are pushed down thereby enabling users to withdraw all lamps for replacement.There is an existing tab on the console storage bin light bulb lens that should be pressed downwards before taking entire lamp out.Disconnect all wires, slide cover sideways revealing one small globe. Pull out old one and insert another new bulb in its place.

For replacing the front turn signal/parking light/side marker light bulbs, remove the headlight housing as well as the bulb holder. After that, take out the old bulb and put in a new one. For the high-mounted brake light and cargo light bulbs, detach the housing while disconnecting its electrical connectors. Then you should twist and remove it from the bulb holder so that you can be able to pull out its old bulb and insert a new one. To replace fog lamp bulbs, unplug wiring from it turning counterclockwise to remove it from a hole in which it was placed. For license plate light bulbs, untwist and remove it off from its holder after that you can be able to pull out an old bulb and insert a new one for replacement purposes. Mirror mounted lights are LED lights; therefore replacing them involves fitting a new LED assembly if they become faulty. The rear fender lights need to be gently pushed or pulled out of their lens before being twisted off from their bulb holders allowing pulling out of an old bulb and inserting a new one instead. To change tailgate lights unscrew screws on this side of light lens so that you get chance of removing it from there with ease. This is how you take off an old bulb by twisting down its holder while installing another one in its place so far as your vehicle's taillight assembly is concerned. Bed storage bin Lightbulbs have their lens removed by taking such lens off by twisting around at its holder level;thereafter,you will be able to pull out an old bulb before fixing anewone in position.The dome light will require you push down the sides of this cover then detach all parts including these bulbs themselves using hands carefully.Insert anewbulb of suitable size properly back into place.To replace glove box lighting facility,it should simply be slid straight direction for removal then another piece inserted into opposite groove whereit cameoff.These reading lamps need to have the sides pried open and then slide it forward until you can be able to remove one end from them.Put in a LED bulb of same size or wattage as that which is being replaced.As forthese vanity light bulbs, the lens has to be pried off from the top part of light assembly so that afterthat you can pull out its old bulb gently and replace it with anewone.Such light fixtures are devised in such a way that their covers are pushed down thereby enabling users to withdraw all lamps for replacement.There is an existing tab on the console storage bin light bulb lens that should be pressed downwards before taking entire lamp out.Disconnect all wires, slide cover sideways revealing one small globe. Pull out old one and insert another new bulb in its place.

For replacing the front turn signal/parking light/side marker light bulbs, remove the headlight housing as well as the bulb holder. After that, take out the old bulb and put in a new one. For the high-mounted brake light and cargo light bulbs, detach the housing while disconnecting its electrical connectors. Then you should twist and remove it from the bulb holder so that you can be able to pull out its old bulb and insert a new one. To replace fog lamp bulbs, unplug wiring from it turning counterclockwise to remove it from a hole in which it was placed. For license plate light bulbs, untwist and remove it off from its holder after that you can be able to pull out an old bulb and insert a new one for replacement purposes. Mirror mounted lights are LED lights; therefore replacing them involves fitting a new LED assembly if they become faulty. The rear fender lights need to be gently pushed or pulled out of their lens before being twisted off from their bulb holders allowing pulling out of an old bulb and inserting a new one instead. To change tailgate lights unscrew screws on this side of light lens so that you get chance of removing it from there with ease. This is how you take off an old bulb by twisting down its holder while installing another one in its place so far as your vehicle's taillight assembly is concerned. Bed storage bin Lightbulbs have their lens removed by taking such lens off by twisting around at its holder level;thereafter,you will be able to pull out an old bulb before fixing anewone in position.The dome light will require you push down the sides of this cover then detach all parts including these bulbs themselves using hands carefully.Insert anewbulb of suitable size properly back into place.To replace glove box lighting facility,it should simply be slid straight direction for removal then another piece inserted into opposite groove whereit cameoff.These reading lamps need to have the sides pried open and then slide it forward until you can be able to remove one end from them.Put in a LED bulb of same size or wattage as that which is being replaced.As forthese vanity light bulbs, the lens has to be pried off from the top part of light assembly so that afterthat you can pull out its old bulb gently and replace it with anewone.Such light fixtures are devised in such a way that their covers are pushed down thereby enabling users to withdraw all lamps for replacement.There is an existing tab on the console storage bin light bulb lens that should be pressed downwards before taking entire lamp out.Disconnect all wires, slide cover sideways revealing one small globe. Pull out old one and insert another new bulb in its place.

For replacing the front turn signal/parking light/side marker light bulbs, remove the headlight housing as well as the bulb holder. After that, take out the old bulb and put in a new one. For the high-mounted brake light and cargo light bulbs, detach the housing while disconnecting its electrical connectors. Then you should twist and remove it from the bulb holder so that you can be able to pull out its old bulb and insert a new one. To replace fog lamp bulbs, unplug wiring from it turning counterclockwise to remove it from a hole in which it was placed. For license plate light bulbs, untwist and remove it off from its holder after that you can be able to pull out an old bulb and insert a new one for replacement purposes. Mirror mounted lights are LED lights; therefore replacing them involves fitting a new LED assembly if they become faulty. The rear fender lights need to be gently pushed or pulled out of their lens before being twisted off from their bulb holders allowing pulling out of an old bulb and inserting a new one instead. To change tailgate lights unscrew screws on this side of light lens so that you get chance of removing it from there with ease. This is how you take off an old bulb by twisting down its holder while installing another one in its place so far as your vehicle's taillight assembly is concerned. Bed storage bin Lightbulbs have their lens removed by taking such lens off by twisting around at its holder level;thereafter,you will be able to pull out an old bulb before fixing anewone in position.The dome light will require you push down the sides of this cover then detach all parts including these bulbs themselves using hands carefully.Insert anewbulb of suitable size properly back into place.To replace glove box lighting facility,it should simply be slid straight direction for removal then another piece inserted into opposite groove whereit cameoff.These reading lamps need to have the sides pried open and then slide it forward until you can be able to remove one end from them.Put in a LED bulb of same size or wattage as that which is being replaced.As forthese vanity light bulbs, the lens has to be pried off from the top part of light assembly so that afterthat you can pull out its old bulb gently and replace it with anewone.Such light fixtures are devised in such a way that their covers are pushed down thereby enabling users to withdraw all lamps for replacement.There is an existing tab on the console storage bin light bulb lens that should be pressed downwards before taking entire lamp out.Disconnect all wires, slide cover sideways revealing one small globe. Pull out old one and insert another new bulb in its place.

To replace the exterior light bulbs, reach behind the headlight housing and rotate the bulb holder counterclockwise to remove it. Then, remove the bulb from the socket and install the new bulb.

Pry off the lens, remove the bulb, and reverse the process for installation.

To replace the center high-mounted brake light, start by removing the trunk lid trim panel and disconnecting the electrical connector. Then, remove the mounting fasteners and the center high-mounted brake light.

It is necessary to replace the bulbs with the headlight housing installed due to electrocution risks. This applies to 2014 and earlier models, as 2015 and later models use LED bulbs that must be replaced as a unit.

To replace these bulbs, remove the headlight housing and the bulb holder. Then, pull out the old bulb and insert the new one.

To replace these bulbs, detach the housing and disconnect the electrical connectors. Twist and remove the bulb holder, then pull out the old bulb and insert the new one.