Jeep L0000H11 Headlamp Bulb

You can Select Your Vehicle to check if L0000H11 fits your vehicle.

To change exterior bulbs, rotate the bulb holder counterclockwise and replace the bulb. For fog lights, disconnect the battery, raise the vehicle, remove the filler panel, disconnect the connector, and replace the bulb and socket. To change the center brake light, remove the trunk lid panel, disconnect the connector, remove the fasteners and light. For taillights, open the trunk, unscrew the fasteners, disconnect the connectors, and replace the bulb. For license plate lights, remove the screws, and replace the bulb. Interior lights aren't separately serviceable. For reading and dome lights, pry off the cover and replace the bulb.

Halogen headlights in Dodge and Chrysler models require different replacement methods. For Dodge, a dual headlamp bulb is used, while Chrysler uses a quad system. To replace, disconnect the negative battery cable, open the hood, and disconnect the electrical connector(s) from the housing. Rotate the bulb counterclockwise and remove it. Install the new bulb by aligning the slots on the bulb socket with the bosses on the mounting hole. Installation is the reverse of removal.

Halogen headlights in Dodge and Chrysler models require different replacement methods. For Dodge, a dual headlamp bulb is used, while Chrysler uses a quad system. To replace, disconnect the negative battery cable, open the hood, and disconnect the electrical connector(s) from the housing. Rotate the bulb counterclockwise and remove it. Install the new bulb by aligning the slots on the bulb socket with the bosses on the mounting hole. Installation is the reverse of removal.

All headlight bulbs except HID low-beam bulb models can be replaced without removing the headlight housing, although if space is limited or hands are too large, the housing should be removed first. For left headlight bulb replacement, the air filter housing must be removed. On 2011 and later models, the dust cap should be turned counterclockwise to remove it. The electrical connector from the headlight bulb must be disconnected by grasping it firmly and pulling it out of the bulb socket terminal, ensuring enough force is applied to release the locking tab. To remove the headlight bulb, it should be turned counterclockwise about 30 degrees, as the bulb and socket are a single assembly with no further disassembly possible; the new bulb will come with its own socket. Installation follows the reverse order of removal. High Intensity Discharge (HID) low-beam bulb models produce three times the light of standard halogen bulbs, consume less energy, and have a lifespan ten times longer. These bulbs operate using an alternating current to ignite xenon gas within a sealed bulb, functioning similarly to vapor-filled streetlights. Instead of a filament, an arc is created between two electrodes to ignite the gas. A ballast module converts battery voltage from 12 volts DC to 800 volts AC, and the HID bulb requires about 10-15 seconds to warm up for normal operation. The igniter, part of the HID bulb, controls the voltage to the electrodes, stepping up the 800 volts AC input to approximately 25,000 volts for ignition and then reducing it to about 85 volts for continued operation.

To change exterior bulbs, rotate the bulb holder counterclockwise and replace the bulb. For fog lights, disconnect the battery, raise the vehicle, remove the filler panel, disconnect the connector, and replace the bulb and socket. To change the center brake light, remove the trunk lid panel, disconnect the connector, remove the fasteners and light. For taillights, open the trunk, unscrew the fasteners, disconnect the connectors, and replace the bulb. For license plate lights, remove the screws, and replace the bulb. Interior lights aren't separately serviceable. For reading and dome lights, pry off the cover and replace the bulb.

To change exterior bulbs, rotate the bulb holder counterclockwise and replace the bulb. For fog lights, disconnect the battery, raise the vehicle, remove the filler panel, disconnect the connector, and replace the bulb and socket. To change the center brake light, remove the trunk lid panel, disconnect the connector, remove the fasteners and light. For taillights, open the trunk, unscrew the fasteners, disconnect the connectors, and replace the bulb. For license plate lights, remove the screws, and replace the bulb. Interior lights aren't separately serviceable. For reading and dome lights, pry off the cover and replace the bulb.

If one is replacing front park/turn signal light bulbs on models with HID headlights, it must be so with the headlight housing removed due to risks of electrocution and this is for 2014 and earlier models since 2015 and later ones uses LED bulbs that come preassembled and is replaced as a whole. For bulb replacement if space is limited, removal of the headlight may be necessary. To replace the left front park/turn signal bulb first you will have to remove the air filter housing then to disconnect the electrical connector you will have to slide the red lock and pull of the connector. Third, unscrew the bulb holder anti-clockwise and then expel the bulb linearly before inserting a new one in place till it clicks into position. As for the inner and outer front parking light bulbs, similar procedure is used, with similar steps to get to the bulb holder. As with the rear sidemarker lights, front sidemarker lights of 2010 and earlier models can be accessed with the bulb from underneath the car, or the headlight housing can be remove to give access to the electrical connector and holder. To change fog light bulb one has to lift the car, and then the front engine splash, then the electrical connector and finally the bulb holder has to be unscrewed anti-clockwise. The center high-mounted stop light assembly is an LED type and it cannot have individual bulbs replaced; the whole assembly requires the electrical connector to be disconnected coupling with the unscrewing of the mounting screws. Opening of taillight bulbs involves getting at the trunk, unscrewing the fastener which is over the carpeting, disconnecting the electrical connector and finally withdrawing the retainers of the taillight assembly to pull out the housing. In licensing plate light bulb replacement some of the procedures that are followed includes removing the revealing screws of the bulb, detaching the bulb and fixing a new one. This may involve prying of the lens of a trunk interior light or reading light to get an access to electrical connectors to remove them from the bulbs or even to push in new bulbs by pulling them straight out. To replace the vanity light bulbs, one has to take off the lens and unscrew the bulb from the contacts, the same procedure applies to the light bulbs of the door courtesy and the rear reading lights.

Remove the entire headlight housing. Disconnect the wiring harness by first releasing the orange lock tab. On models with two headlights, rotate the bulb counter clockwise to remove it. Twist the bulb housing counterclockwise to remove it. On models with four headlights, twist the bulb access cover counterclockwise and remove it. Rotate the bulb counterclockwise to remove it. Installation is the reverse of removal.

For replacing the front turn signal/parking light/side marker light bulbs, remove the headlight housing as well as the bulb holder. After that, take out the old bulb and put in a new one. For the high-mounted brake light and cargo light bulbs, detach the housing while disconnecting its electrical connectors. Then you should twist and remove it from the bulb holder so that you can be able to pull out its old bulb and insert a new one. To replace fog lamp bulbs, unplug wiring from it turning counterclockwise to remove it from a hole in which it was placed. For license plate light bulbs, untwist and remove it off from its holder after that you can be able to pull out an old bulb and insert a new one for replacement purposes. Mirror mounted lights are LED lights; therefore replacing them involves fitting a new LED assembly if they become faulty. The rear fender lights need to be gently pushed or pulled out of their lens before being twisted off from their bulb holders allowing pulling out of an old bulb and inserting a new one instead. To change tailgate lights unscrew screws on this side of light lens so that you get chance of removing it from there with ease. This is how you take off an old bulb by twisting down its holder while installing another one in its place so far as your vehicle's taillight assembly is concerned. Bed storage bin Lightbulbs have their lens removed by taking such lens off by twisting around at its holder level;thereafter,you will be able to pull out an old bulb before fixing anewone in position.The dome light will require you push down the sides of this cover then detach all parts including these bulbs themselves using hands carefully.Insert anewbulb of suitable size properly back into place.To replace glove box lighting facility,it should simply be slid straight direction for removal then another piece inserted into opposite groove whereit cameoff.These reading lamps need to have the sides pried open and then slide it forward until you can be able to remove one end from them.Put in a LED bulb of same size or wattage as that which is being replaced.As forthese vanity light bulbs, the lens has to be pried off from the top part of light assembly so that afterthat you can pull out its old bulb gently and replace it with anewone.Such light fixtures are devised in such a way that their covers are pushed down thereby enabling users to withdraw all lamps for replacement.There is an existing tab on the console storage bin light bulb lens that should be pressed downwards before taking entire lamp out.Disconnect all wires, slide cover sideways revealing one small globe. Pull out old one and insert another new bulb in its place.

Remove the entire headlight housing. Disconnect the wiring harness by first releasing the orange lock tab. On models with two headlights, rotate the bulb counter clockwise to remove it. Twist the bulb housing counterclockwise to remove it. On models with four headlights, twist the bulb access cover counterclockwise and remove it. Rotate the bulb counterclockwise to remove it. Installation is the reverse of removal.

On Dodge models, the headlights use a dual headlamp bulb. On Chrysler models, a "quad system" is used, with one bulb for high beam and one bulb for low beam.

Twist the bulb access cover counterclockwise and remove it. Then, rotate the bulb counterclockwise to remove it.

Installation is the reverse of removal.

To replace these bulbs, detach the housing and disconnect the electrical connectors. Twist and remove the bulb holder, then pull out the old bulb and insert the new one.

To replace fog lamp bulbs, disconnect the wiring and remove the bulb by turning it counterclockwise.

Twist the bulb access cover counterclockwise and remove it. Then, rotate the bulb counterclockwise to remove it.

To replace these bulbs, gently push and pull out the light lens, then twist and remove the bulb holder. Pull out the old bulb and insert the new one.

To replace vanity light bulbs, pry the lens from the light assembly and gently pull out the bulb. Insert the new bulb and reassemble.

To replace these bulbs, twist and remove the bulb holder, then pull out the old bulb and insert the new one.

Twist the bulb housing counterclockwise to remove it.