Mopar L0009006 Headlamp Bulb

You can Select Your Vehicle to check if L0009006 fits your vehicle.

To replace the ash tray/cup holder bulb, insert a small screwdriver into the slot in the light bezel and pry it from the cubby bin, then puff the socket from the light bezel and remove the bulb from the socket, with installation being the reverse of removal. For the center mounted brake light, open the trunk lid, rotate the bulb holder 1/4-turn counterclockwise to withdraw it from the light bezel, grasp the bulb and pull it out, then using gloves or a clean shop towel, insert the new bulb into the holder, ensuring not to touch the bulb surface with fingers, and if touched, clean it with rubbing alcohol before inserting the holder back into the light bezel and rotating it clockwise to lock it in place before closing the trunk. To change the dome/amp bulb, use a small screwdriver to pry the dome light lens from the assembly, remove the bulb, and reinstall in reverse order. For the fog light, remove the screws securing the fog light assembly to the front bumper, withdraw it, grasp the bulb holder, rotate it 1/4-turn counterclockwise, remove it from the light bezel, pull the bulb out, insert a new bulb using gloves or a clean shop towel, and if touched, clean it with rubbing alcohol before reinserting the holder into the light bezel and locking it in place, then install the light bezel back into the bumper and secure it with screws while checking and adjusting the fog light beam. To replace the glove box light, open the glove box, pull down on the light/switch assembly to disengage it, puff the bulb from the socket, and reinstall in reverse order. For the headlight bulb, remove the headlight assembly, grasp the bulb holder retaining ring, rotate it 1/4-turn counterclockwise, remove the bulb holder, pull the bulb out, insert a new bulb using gloves or a clean shop towel, and if touched, clean it with rubbing alcohol before installing the bulb holder back into the headlight assembly and locking it in place, then attach the electrical connectors and reinstall the headlight assembly, adjusting if necessary. For instrument panel bulbs, depending on the location, access may be from under the dashboard; remove the instrument cluster, grasp the bulb holder, rotate it 1/4-turn counterclockwise, remove it, pull the bulb from the holder, install a new bulb, insert the holder back into the instrument panel, and lock it in place before reinstalling the instrument cluster. To change the license plate light, remove the retaining screws of the light assembly, withdraw it from the rear bumper, grasp the bulb holder, rotate it 1/4-turn counterclockwise, remove it, install a new bulb, insert the holder back into the light bezel, lock it in place, and secure the light bezel into the bumper with screws. For the park/turn signal bulb, remove the headlight assembly, grasp the bulb holder, rotate it 1/4-turn counterclockwise, remove the holder, push the bulb down slightly, rotate it 1/4-turn counterclockwise to withdraw it, install a new bulb, reinstall the bulb holder in the headlight assembly, attach the electrical connectors, and reinstall the headlight assembly, adjusting if necessary. To replace tail, stop, back-up, and turn signal bulbs, open the trunk, separate the trunk lining from the rear tail lamp assembly, unscrew and remove the plastic wing-nuts securing the tail light assembly, withdraw it from the quarter panel, disconnect the wiring harness, rotate the bulb holder 1/4-turn counterclockwise to withdraw it from the light bezel, pull the bulb from the holder, and reinstall in reverse order. For the trunk light, open the trunk, carefully insert a trim stick between the rear self-reinforcement panel and cargo lamp lens to pry it downward and remove it, grasp the bulb and remove it from the socket, and reinstall in reverse order. For the under hood lamp, disconnect the wiring harness, rotate the bulb counterclockwise, remove it, and reinstall in reverse order. Finally, for the visor vanity lamp, lower the visor, carefully insert a trim stick between the visor and vanity lamp lens to pry it outward and remove it, grasp the bulb and remove it from the socket, and reinstall in reverse order.

On these models, the headlight high and low beam and park/turn signal bulbs are separate and mounted in the headlight housing. Begin by loosening the front wheel lug nuts, then raise the vehicle and support it securely on jackstands. Remove the wheel and detach the headlight access panel from the fenderwell splash shield by rotating it out of the fenderwell. Grasp the appropriate bulb holder, rotate it counterclockwise, and remove it from the headlight housing. The headlight bulbs are integral with the holder and replaced as a unit; unplug the electrical connector and connect it to the new bulb, taking care not to touch the bulb surface with your fingers to avoid overheating and premature failure. If the bulb surface is touched, clean it with rubbing alcohol. For park/turn signals, grasp the bulb and pull it out of the holder, then using gloves or a clean shop towel, insert the new bulb into the holder. Install the bulb and holder in the headlight housing, rotating it clockwise to lock it in place. Finally, install the headlight access panel, then the wheel and lug nuts, tightening the lug nuts to the specified torque.

Halogen headlights in Dodge and Chrysler models require different replacement methods. For Dodge, a dual headlamp bulb is used, while Chrysler uses a quad system. To replace, disconnect the negative battery cable, open the hood, and disconnect the electrical connector(s) from the housing. Rotate the bulb counterclockwise and remove it. Install the new bulb by aligning the slots on the bulb socket with the bosses on the mounting hole. Installation is the reverse of removal.

The procedure is useful when you need to learn how to change a headlight bulb without having to unmount the headlight housing; but if your hands are too large, then it may be almost impossible to change the bulb without having to unmount the headlight housing. Beginning with the engine you should switch on the engine and with the front wheels rotated to as many left or right as possible in order to create sufficient space to work on. Or you could: failed to understand the signal-loosen the front wheel lug nuts, lift the front of the vehicle, and support it on jackstands, then remove the wheel. Then proceed to the inside of the wheel housing to get rid of the access panel of the housing of electrical connectors of headlights. Next, unscrew the bulb socket from the headlight housing in anticlockwise direction and come out of the housing. Pull the tab at the bottom and come off the electrical connector which has a sliding lock, push it away from the unit towards harness and lift the tab on top. Last of all, installation is the sort of procedure that is opposite to the removal procedure.

Remove the entire headlight housing. Disconnect the wiring harness by first releasing the orange lock tab. On models with two headlights, rotate the bulb counter clockwise to remove it. Twist the bulb housing counterclockwise to remove it. On models with four headlights, twist the bulb access cover counterclockwise and remove it. Rotate the bulb counterclockwise to remove it. Installation is the reverse of removal.

Remove the entire headlight housing. Disconnect the wiring harness by first releasing the orange lock tab. On models with two headlights, rotate the bulb counter clockwise to remove it. Twist the bulb housing counterclockwise to remove it. On models with four headlights, twist the bulb access cover counterclockwise and remove it. Rotate the bulb counterclockwise to remove it. Installation is the reverse of removal.

To remove the headlight bulb from the housing, you need to rotate it counterclockwise and pull it out.

To replace a headlight bulb, you need to remove the air filter housing (if replacing a left headlight bulb), disconnect the electrical connector from the headlight bulb, and then turn the headlight bulb counterclockwise about 30-degrees to remove it from the headlight housing. Installation is the reverse of removal.

Rotate the bulb counter clockwise to remove it.