Mopar 5184693AE Engine Intake Manifold

You can Select Your Vehicle to check if 5184693AE fits your vehicle.

To start, turn off the fuel pump, unplug the cable from the battery negative terminal and then wait for about fifteen minutes. Then, the air intake duct has to be taken off as well as the filter housing. Remove the upper intake manifold vacuum hoses and electrical connectors and unbolt and remove the vacuum and electrical connectors from the throttle body and the electronic throttle control system. Remove the EGR Pipe from the upper intake manifold which is followed by the removal of the upper Intake manifold support brackets. Relax the upper intake manifold bolts in the reverse order you tightened them and pull off the upper intake manifold including the foam insulator pad. Thoroughly wash and inspect the sealing surfaces of the upper intake manifold to the lower intake manifold, and if the existing gaskets supplied have damage to them then they should be replaced, however in most cases the gaskets that have been removed will not have any damage and can therefore be reused. The upper intake manifold has to be placed back onto the lower intake manifold and secured by tightened bolts in the proper sequence and using the appropriate torque to get them tightened. To get to the lower intake manifold first you must take off the upper intake manifold after that disconnect any of the hoses that may hinder you when removing the lower intake manifold. Disconnect the fuel rail and the injectors from the lower intake manifold, then 1/4 turn each of the lower intake manifold mounting bolts or nuts starting from the reverse sequence of how they were tighten to allow them to be unscrewed. Sometimes some force may be required to tear the gasket and separate the manifold from the cylinder heads, but do not pry between the manifold and the heads because the gasket sealing surfaces are easily damaged. Clean and inspect the sealing surfaces of the lower intake manifold to the cylinder head; gaskets if bad should be replaced, if not they can be reused. Align the second lower intake manifold to the engine with correct fit of gasket and manifold over the cylinder head. The fuel rail and injectors are inserted to the cylinder heads and lower manifold, and the fuel rail retaining bolts must be loosely put for the proper gasket orientation of the remaining lower intake manifold bolts. Torque the bolts gradually to the measured torque level and then reverse the process of removing them, and start the engine to note any signs of fuel leaks, vacuum leak and coolants leak.

First, remove the upper intake manifold, then label and detach any remaining hoses that may interfere with the removal. Remove the fuel rail and injectors, loosen the lower intake manifold mounting bolts in 1/4-turn increments until they can be removed by hand, and be cautious not to pry between the manifold and the heads to avoid damaging the gasket sealing surfaces.

Unscrew the intake manifold lower bracket, remove the intake tube, and loosen the upper support bracket bolts. Remove the throttle body bracket and throttle body, cut through the fuel injector foam silencing pad, disconnect the VVAA solenoid electrical connectors, and remove the intake manifold silencer cover.

Unscrew the intake manifold lower bracket, remove the intake tube, and loosen the upper support bracket bolts. Remove the throttle body bracket and throttle body, cut through the fuel injector foam silencing pad, disconnect the VVAA solenoid electrical connectors, and remove the intake manifold silencer cover.

Clean the mounting surfaces of the lower intake manifold and the upper manifold, inspecting the rubber O-ring gasket for any signs of deterioration; if it is in good condition, it can be reused.

Install the gasket into the groove in the upper intake manifold, then place the upper intake manifold onto the lower intake manifold, tightening the bolts in a circular pattern starting with the center bolts.

Clean and inspect the sealing surfaces and gaskets, replacing any that are damaged, while reusing those that are intact.

Refill the cooling system if it was drained, start the engine, and check for leaks and proper operation.

Disconnect the negative battery cable from the remote ground terminal or battery, and if equipped, remove the engine cover.

Install the intake manifold bolts and tighten them following the recommended sequence to the specified torque.

Disconnect the cable from the negative terminal of the battery, ensuring that on 2015 and later models with an Intelligent Battery Sensor, the IBS connector is disconnected first.

Remove the intake manifold support bracket and detach the EGR tube from the exhaust manifold.

Proceed to remove the fuel injectors and the MAP sensor bracket bolts, then detach the PCV valve hose.

Clean the mounting surfaces of the lower intake manifold and the upper manifold, inspecting the rubber O-ring gasket for any signs of deterioration; if it is in good condition, it can be reused.

Reinstall the remaining components in reverse order, change the oil and filter, refill the cooling system, start the engine, and check for leaks.