Make sure this part fits

Mopar 5140829AB Module-Fuel Pump/Level Unit

2005 Jeep Liberty 5140829AB

Customer Questions & Expert Answers (3)
Mopar 5140829AB Module-Fuel Pump/Level Unit
  • Part Description
    Module Kit Fuel Pump/Level Unit
  • Replaced By
    68011583AH
  • Manufacturer
    Mopar
Make sure this part fits
$344.30 MSRP: $525.00
You Save: $180.70 (35%)
1
ADD TO CART
  • Related Parts
  • Product Specifications
  • Vehicle Fitment
  • Customer Questions & Expert Answers
  • Product Specifications

    BrandGenuine Mopar
    Manufacturer Part Number5140829AB
    Part DescriptionModule Kit Fuel Pump/Level Unit
    Item Dimensions16.5 x 11.7 x 6.7 inches
    Item Weight3.90 Pounds
    ConditionNew
    Fitment TypeDirect Replacement
    ManufacturerMopar
    SKU5140829AB
    WarrantyThis genuine Mopar part is guaranteed by Mopar's factory warranty.
    Shipping & ReturnShipping Policy Return Policy
    Warning: California’s Proposition 65
  • Vehicle Fitment

    Year Make Model Engine Important vehicle option details
    2005 Jeep Liberty4 Cyl 2.4L, 6 Cyl 3.7LLimited Edition 2WD, Limited Edition 4WD, Renegade 2WD, Renegade 4WD, Sport 2WD, Sport 4WD
  • Customer Questions & Expert Answers

    Q:
    Will this fit my truck? Posted by MoparPartsGiant Specialist
    A:
    You can Select Your Vehicle to check if 5140829AB fits your vehicle.
    Posted by MoparPartsGiant Specialist
    Q:
    How to Replace the Fuel Pump Module? Posted by Customer
    A:
    The fuel pump module consists of an upper section containing the fuel pressure regulator and fuel pump check valve, and a lower section consisting of the electric fuel pump and the fuel pick-up/inlet filter. The fuel pump module is replaced as a complete assembly. Relieve the fuel system pressure. Disconnect the cable from the negative battery terminal. Check the vehicle to see if it is equipped with a fuel pump access cover, then remove it. Drill-out the rivets on the two rear-most cargo hold-down clamps and remove the clamps. Fold the carpeting forward. Remove the access cover nuts. Use a knife blade to cut the seal or use a heat gun to apply heat to the outer edge of the access cover, then carefully pry up on the cover and remove it. Clean the area surrounding the fuel lines and upper section of the fuel module to prevent dirt from entering the fuel system. Disconnect the fuel lines and electrical connector from the upper module, as necessary. Mark the orientation of the module to the fuel tank before removing the module. Using a pair of large pliers to turn the lockring, or using a hammer and a brass drift, tap on the lockring to turn it counterclockwise to remove the upper section of the fuel pump module from the tank. Carefully lift up the upper section, then secure the rubber gasket to prevent it from falling into the tank. Detach and secure the fuel lines and electrical connector from the bottom side of the upper section. Remove the upper section from the tank. Using a siphoning kit, siphon the all of the fuel through the upper module opening, into an approved gasoline container. Reach inside the tank and press and release the plastic lock while lifting the tab. Slide the lower section to the right side of the tank to release it from the two guides in the fuel tank. Remove the lower section of the fuel pump module. Installation is the reverse of removal with the following additions: Install the lower section into the fuel tank by sliding it to the left and pressing down on the locking tab. Always replace the upper section gasket with a new one. Position the notch on the upper section so that it faces the rear of the vehicle, then install it. If equipped, apply silicone sealant to the bottom of the fuel pump access cover. After positioning the carpet in place, install two new rivets to secure the cargo hold-down clamps.
    Posted by MoparPartsGiant Specialist
    Q:
    What should be done to check the fuel pressure for the 2012 Jeep Liberty? Posted by Customer
    A:
    Relieve the fuel pressure, remove the cap from the fuel pressure test port on the fuel rail and attach a fuel pressure gauge. Start the engine and check the pressure on the gauge. If the pressure is not within specifications, check for a restriction in the fuel system if the pressure is lower than specified. If the pressure is higher than specified, replace the fuel pressure regulator.
    Posted by MoparPartsGiant Specialist
    See expert answers on similar Fuel Pump
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

Genuine Mopar Part 5140829AB, the Right Choice

To ensure reliability, purchase Mopar part # 5140829AB Module-Fuel Pump/Level Unit. It is sometimes referred to as Mopar Fuel Pump. For Mopar owners with dreams of keeping their vehicles running in prime condition, choosing OEM parts is a smart decision. Meticulously crafted, these parts follow strict factory specifications and are manufactured in top-notch facilities with advanced technologies. Furthermore, they undergo rigorous testing to ensure durability and safety, making them a reliable choice for Mopar owners. This part fits specific Jeep Liberty models.

MoparPartsGiant.com is a leading supplier of genuine Mopar parts and accessories such as Mopar 5140829AB Module-Fuel Pump/Level Unit. Wondering where to find exceptional quality and affordable OEM Mopar parts? You have already come to the right place. Our website boasts a huge selection of genuine Mopar parts at the most economical prices possible. What's more, all parts come with a manufacturer's warranty. For detailed Jeep parts information, click here.

Why choose Mopar Parts Giant

  • Dedicated Service

    Your complete satisfaction is our #1 goal

  • Lowest Prices

    Best deals on genuine OE parts from dealerships

  • Fast Delivery

    Orders are processed and delivered promptly