Make sure this part fits

Mopar 52114720AB Rear Axle Shaft

2007-2010 Dodge Ram 1500 52114720AB

Customer Questions & Expert Answers (7)
Mopar 52114720AB Rear Axle Shaft
  • Part Description
    Shaft-Axle Rear
  • Position
    Rear
  • Replaces
    52114720AA
  • Manufacturer
    Mopar
Make sure this part fits
$542.30 MSRP: $827.00
You Save: $284.70 (35%)
1
ADD TO CART
  • Related Parts
  • Product Specifications
  • Vehicle Fitment
  • Customer Questions & Expert Answers
  • Product Specifications

    BrandGenuine Mopar
    Manufacturer Part Number52114720AB
    Part DescriptionShaft-Axle Rear
    Other NamesAxle Shaft
    Item Dimensions38.1 x 7.2 x 7.2 inches
    Item Weight26.40 Pounds
    PositionRear
    ConditionNew
    Fitment TypeDirect Replacement
    Replaces52114720AA
    Require Quantity2
    ManufacturerMopar
    SKU52114720AB
    WarrantyThis genuine Mopar part is guaranteed by Mopar's factory warranty.
    Shipping & ReturnShipping Policy Return Policy
    Warning: California’s Proposition 65
  • Vehicle Fitment

    Year Make Model Engine Important vehicle option details
    2007-2010 Dodge Ram 15006 Cyl 3.7L, 8 Cyl 4.7L, 8 Cyl 5.7LLaramie Crew Cab 2WD, Laramie Crew Cab 4WD, Laramie Quad Cab 2WD, Laramie Quad Cab 4WD, Laramie Regular Cab 4WD, SLT Crew CAB 2WD, SLT Crew Cab 4WD, SLT HEV Crew Cab 4WD, SLT Quad Cab 2WD, SLT Quad Cab 4WD, SLT Regular Cab 2WD, SLT Regular Cab 4WD, ST Crew Cab 2WD, ST Crew Cab 4WD, ST Quad Cab 2WD, ST Quad Cab 4WD, ST Regular Cab 2WD, ST Regular Cab 4WD
  • Customer Questions & Expert Answers

    Q:
    Will this fit my truck? Posted by MoparPartsGiant Specialist
    A:
    You can Select Your Vehicle to check if 52114720AB fits your vehicle.
    Posted by MoparPartsGiant Specialist
    Q:
    How do you remove the drive axle? Posted by Customer
    A:
    To remove the Axle Shaft, start by loosening the wheel lug nuts, then raise and securely support the vehicle with jack stands, and remove the wheel(s). Next, remove the caliper and brake disc, and disconnect the ABS sensor, securing the sensor and wire harness aside. Proceed to remove the Axle Shaft/hub nut, using a pry bar between two wheel studs to prevent the hub from turning while loosening the nut. Support the lower control arm with a floor jack, slightly raising it to relieve the spring force on the upper control arm. Remove the shock absorber lower mounting bolt and the upper control arm ball joint nut, allowing you to separate the control arm from the steering knuckle. Utilizing a pry bar or slide hammer with a CV joint adapter, carefully pry the inner CV joint assembly from the front differential, ensuring not to damage the differential. Suspend the Axle Shaft with wire to prevent damage to the outer CV joint. Proceed to pull the steering knuckle out and away from the outer CV joint, using necessary tapping or pulling methods if the Axle Shaft is stuck. Once the Axle Shaft is free from the hub splines, pull out the hub/knuckle assembly, remove the support wire, and guide the Axle Shaft out from under the vehicle. For installation, reverse the removal steps, ensuring proper cleaning of splines and sealing surfaces, as well as applying grease to the inner tripod CV joint. When installing the Axle Shaft, push it in sharply to seat the set-ring on the splines of the inner CV joint and verify its proper seating. Tighten the Axle Shaft/hub nut and wheel lug nuts to specified torques and use a new upper ball joint-to-steering knuckle nut. Tighten the upper ball joint nut to the recommended torque.
    Posted by MoparPartsGiant Specialist
    Q:
    What should be done before installing the axleshaft for the 2010 Dodge Ram 1500? Posted by Customer
    A:
    Before installation, the axleshaft should be cleaned and a thin film of wheel bearing grease should be applied to the shaft splines, seal contact surface, and hub bore.
    Posted by MoparPartsGiant Specialist
    See expert answers on similar Axle Shaft
    Q:
    What is the first step in removing the axle assembly for the 2009 Dodge Ram 1500? Posted by Customer
    A:
    Loosen the front wheel lug nuts and raise the front of the vehicle using jack stands.
    Posted by MoparPartsGiant Specialist
    See expert answers on similar Axle Shaft
    Q:
    What should you inspect and replace if necessary for a full-floating axleshaft for the 2009 Dodge Ram 1500? Posted by Customer
    A:
    Inspect and replace the hub and bearing seals and bearings if necessary.
    Posted by MoparPartsGiant Specialist
    See expert answers on similar Axle Shaft
    Q:
    How should the brake line junction block be detached from the axle tube for the 2010 Dodge Ram 1500? Posted by Customer
    A:
    The vent hose fitting should be unscrewed to detach the brake line junction block from the axle tube.
    Posted by MoparPartsGiant Specialist
    See expert answers on similar Axle Shaft
    Q:
    What does the rear axle assembly consist of for the 2010 Dodge Ram 1500? Posted by Customer
    A:
    The rear axle assembly consists of a straight, hollow housing enclosing a differential assembly and axleshafts.
    Posted by MoparPartsGiant Specialist
    See expert answers on similar Axle Shaft
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

Genuine Mopar Part 52114720AB, the Right Choice

To ensure reliability, purchase Mopar part # 52114720AB Rear Axle Shaft. It is sometimes referred to as Mopar Axle Shaft. For Mopar owners with dreams of keeping their vehicles running in prime condition, choosing OEM parts is a smart decision. Meticulously crafted, these parts follow strict factory specifications and are manufactured in top-notch facilities with advanced technologies. Furthermore, they undergo rigorous testing to ensure durability and safety, making them a reliable choice for Mopar owners. This part fits specific Dodge Ram 1500 models.

MoparPartsGiant.com is a leading supplier of genuine Mopar parts and accessories such as Mopar 52114720AB Rear Axle Shaft. Wondering where to find exceptional quality and affordable OEM Mopar parts? You have already come to the right place. Our website boasts a huge selection of genuine Mopar parts at the most economical prices possible. What's more, all parts come with a manufacturer's warranty. For detailed Dodge parts information, click here.

Why choose Mopar Parts Giant

  • Dedicated Service

    Your complete satisfaction is our #1 goal

  • Lowest Prices

    Best deals on genuine OE parts from dealerships

  • Fast Delivery

    Orders are processed and delivered promptly