Mopar 56044736AC Engine Starter

You can Select Your Vehicle to check if 56044736AC fits your vehicle.

To disconnect the starter motor, begin by disconnecting the cable(s) from the negative battery terminal(s). Then, raise the vehicle and support it securely on jackstands. On certain models with 4WD and specific transmissions, there may be a support bracket blocking access to the lower starter mounting bolt. If present, remove the support bracket bolts and pry it aside. Remove the heat shield, if equipped, from the starter motor. Next, remove the nut securing the battery cable to the terminal stud on the starter solenoid and disconnect the cable from the terminal stud. Disconnect the electrical connector from the spade terminal on the solenoid. On models with a manual transmission, remove the starter mounting bolt and nut. On models with an automatic transmission, remove the two starter mounting bolts. Move the starter motor towards the front of the vehicle until the nose of the starter pinion housing clears the transmission bellhousing. Tilt the nose down and lower the starter to access the wiring connectors more easily. Finally, disconnect the battery cable and electrical connector from the terminals on the starter motor solenoid and remove the starter. For HEMI engines, follow a similar process, but also remove the two starter motor mounting bolts. For diesel engines, disconnect the wiring harness and battery cable from the starter, remove the three starter mounting bolts, and then remove the starter. Installation is the reverse of removal for all engine types.

Start by checking the battery cables and connections, testing the battery's condition, and examining the starter motor wiring. Check the related fuses and inspect the ignition switch circuit. Verify the operation of the clutch pedal position switch or the TR sensor. If the starter does not activate, check for battery voltage at the starter solenoid. If voltage is present, remove and bench test the starter motor assembly. If the pinion drive extends but does not rotate, the solenoid is operational but the starter motor is defective. If the solenoid plunger extends and rotates the pinion drive, the starter assembly is functioning correctly.

Start by checking the cleanliness and tightness of the battery cable clamps at the battery connection. Inspect the battery cables for any defects and replace them if necessary. Test the battery's condition, and if it fails the tests, replace it with a new one. Examine the starter motor wiring and connections, ensuring the mounting bolts are tight. Check the related fuses in the engine compartment fuse box and inspect the ignition switch circuit. Verify the operation of the clutch pedal position switch or the Transmission Range (TR) sensor, as they provide voltage to the starter solenoid.

Remove the nut that secures the battery cable to the terminal stud on the starter solenoid, disconnect the cable from the terminal stud and disconnect the electrical connector from the spade terminal on the solenoid. Remove the two starter mounting bolts. Move the starter motor toward the front of the vehicle until the nose of the starter pinion housing clears the transmission bellhousing, then lift the nose down and, if you haven't already done so, lower the starter until you can disconnect the electrical connector and remove the nut that secures the battery cable to the terminal stud on the starter solenoid. Once everything is disconnected, remove the starter. Caution: The starter motor is fairly heavy, so be sure to support it while removing it. Do NOT allow it to hang by the wiring harness.

First, check the following items: a) Make sure the battery cable clamps, where they connect to the battery, are clean and tight. b) Check the condition of the battery cables. Replace any defective battery cables with new parts. c) Test the condition of the battery. If it does not pass all the tests, replace it with a new battery. d) Check the starter motor wiring and connections. e) Check the starter motor mounting bolts for tightness. f) Check the related fuses in the engine compartment fuse box. If they're blown, determine the cause and repair the circuit. g) Check the ignition switch circuit for correct operation. h) Check the starter relay. i) Check the operation of the Transmission Range (TR) sensor. This system must operate correctly to provide battery voltage to the starter solenoid.

Begin by disconnecting the cable(s) from the negative battery terminal(s). Raise the vehicle and support it securely on jackstands. On certain models with 4WD and specific transmissions, there may be a support bracket blocking access to the lower starter mounting bolt. If present, remove the support bracket bolts and pry it aside. Remove the heat shield, if equipped, from the starter motor. Next, remove the nut securing the battery cable to the terminal stud on the starter solenoid and disconnect the cable from the terminal stud. Disconnect the electrical connector from the spade terminal on the solenoid. On models with a manual transmission, remove the starter mounting bolt and nut. On models with an automatic transmission, remove the two starter mounting bolts. Move the starter motor towards the front of the vehicle until the nose of the starter pinion housing clears the transmission bellhousing. Tilt the nose down and lower the starter to access the wiring connectors more easily. Finally, disconnect the battery cable and electrical connector from the terminals on the starter motor solenoid and remove the starter. For HEMI engines, follow a similar process, but also remove the two starter motor mounting bolts. For diesel engines, disconnect the wiring harness and battery cable from the starter, remove the three starter mounting bolts, and then remove the starter.