How to replace a drive axle boot and Axle Shaft on Chrysler 300?

If a Axle Shaft boot has failed, the entire shaft assembly must be replaced as boots are not serviceable separately. To remove, start by removing the wheel cover or hub cap and break the Axle Shaft/hub nut loose with a socket and large breaker bar. Block the front wheels to prevent the vehicle from rolling. Loosen the wheel lug nuts, raise the rear of the vehicle, and support it securely on jack stands. Remove the wheel. Remove the Axle Shaft/hub nut and discard it. Drain the gear lubricant from the differential. Disconnect the driveshaft from the differential and remove the rear exhaust pipe and muffler. Pry the inner CV joint out of the differential just far enough to release the snap-ring. The Axle Shaft can't be removed from the differential until the differential has been lowered. Support the differential with a floor jack. Remove the mounting fasteners securing the differential to the crossmember and differential mount. Carefully lower the differential enough to separate the Axle Shaft(s) from the differential. Pull the Axle Shaft out of the hub flange. If it sticks, tap it out with a soft-faced hammer. Installation is the reverse of removal, noting the following points: Remove the rubber isolation washer from the outer CV joint stub shaft and inspect it. Replace it if necessary. Tighten the differential mounting bolts to the torque. Install a new Axle Shaft/hub nut. Tighten the hub nut securely, but don't try to tighten it to the actual torque specification until you've lowered the vehicle to the ground. Fill the differential with the type and amount of lubricant specified. Install the wheels and lower the vehicle to the ground. Tighten the wheel lug nuts to the torque. Tighten the Axle Shaft/hub nut to the torque. Install the wheel cover or hub cap.

Genuine Chrysler 300 Axle Shaft

Car Axle Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

72 Axle Shafts found

View related parts
Chrysler 300 Axle Shaft-Cv Joint Half Shaft Left
Part Number: 4578601AA
$432.07 MSRP: $664.00
You Save: $231.93 (35%)
ADD TO CART
Product Specifications
- Other Name: Shaft-Axle Half; Axle Assembly, Drive Axle
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2005-2023 Chrysler 300 | Base AWD, C AWD, C John Varvatos AWD, C Luxury Series AWD, C Platinum AWD, Limited AWD, S AWD, S V6 AWD, S V8 AWD, Touring AWD | 6 Cyl 3.5L, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.6L, 8 Cyl 5.7 L GAS, 8 Cyl 5.7L, 8 Cyl 6.4 L GAS
View related parts
Chrysler 300 Rear-Axle Assembly Or Cv Shaft
Part Number: 4578732AE
$522.64 MSRP: $797.00
You Save: $274.36 (35%)
ADD TO CART
Product Specifications
- Other Name: Shaft-Axle Half; Axle Assembly
- Replaces: 4578732AC, 4578732AD, 4578732AB, 68194754AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2012-2014 Chrysler 300 | C John Varvatos RWD, C Luxury Series RWD, C RWD, C SRT8 RWD, S Luxury Series RWD, S RWD, SRT Core RWD, SRT Premium RWD | 8 Cyl 6.4L
- 2009-2010 Chrysler 300 | C RWD, C SRT8 RWD, Touring RWD | 8 Cyl 6.1L
View related parts
Chrysler 300 Rear Left Driver Axle Shaft Assembly
Part Number: 53010749AA
$501.55 MSRP: $762.00
You Save: $260.45 (35%)
ADD TO CART
Product Specifications
- Other Name: Shaft-Axle Half; Axle Assembly
- Position: Rear Driver Side
- Replaces: 53010671AB, 53010671AC, 53010671AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2023 Chrysler 300 | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.4 L GAS
- 2015-2020 Chrysler 300 | C Platinum RWD, C RWD, Limited RWD, S RWD, SRT Core RWD, SRT Premium RWD | 8 Cyl 6.4L
View related parts
Chrysler 300 Axle Shaft Assembly Driveline And Axles
Part Number: 4578600AA
$436.60 MSRP: $664.00
You Save: $227.40 (35%)
ADD TO CART
Product Specifications
- Other Name: Shaft-Axle Half
- Replaced by: 4578600AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2005-2017 Chrysler 300 | Base AWD, C AWD, C John Varvatos AWD, C Luxury Series AWD, C Platinum AWD, Limited AWD, S AWD, S V6 AWD, S V8 AWD, Touring AWD | 6 Cyl 3.5L, 6 Cyl 3.6L, 8 Cyl 5.7L
View related parts
Chrysler 300 Axle Half Shaft
Part Number: 68258859AB
$549.95 MSRP: $835.00
You Save: $285.05 (35%)
ADD TO CART
Product Specifications
- Other Name: Shaft-Axle Half; Axle Assembly
- Replaces: 68258859AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2015-2023 Chrysler 300 | C Platinum RWD, C RWD, Limited RWD, S RWD | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 5.7L, 8 Cyl 6.4 L GAS
View related parts
Chrysler 300 Axle Half Shaft Left
Part Number: 4578733AE
$536.75 MSRP: $812.00
You Save: $275.25 (34%)
ADD TO CART
Product Specifications
- Other Name: Shaft-Axle Half; Axle Assembly
- Position: Driver Side
- Replaces: 4578733AC, 68194755AA, 4578733AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2012-2014 Chrysler 300 | C John Varvatos RWD, C Luxury Series RWD, C RWD, C SRT8 RWD, S Luxury Series RWD, S RWD, SRT Core RWD, SRT Premium RWD | 8 Cyl 6.4L
- 2009-2010 Chrysler 300 | C RWD, C SRT8 RWD, Touring RWD | 8 Cyl 6.1L
View related parts
Chrysler 300 Axle Half Shaft
Part Number: 4578732AB
$526.85 MSRP: $797.00
You Save: $270.15 (34%)
ADD TO CART
Product Specifications
- Other Name: Shaft-Axle Half
- Replaced by: 4578732AE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009 Chrysler 300 | C RWD, C SRT8 RWD | 8 Cyl 6.1L
View related parts
Chrysler 300 Axle Half Shaft
Part Number: 4578733AB
$536.75 MSRP: $812.00
You Save: $275.25 (34%)
ADD TO CART
Product Specifications
- Other Name: Shaft-Axle Half
- Replaced by: 4578733AE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009-2010 Chrysler 300 | C RWD, C SRT8 RWD, Touring RWD | 8 Cyl 6.1L
View related parts
Chrysler 300 Axle Shaft Front Left
Part Number: R4578601AA
$244.15 MSRP: $295.00
You Save: $50.85 (18%)
ADD TO CART
Product Specifications
- Other Name: Shaft-Axle Half; Axle Assembly
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2017-2020 Chrysler 300 | C AWD, C Platinum AWD, Limited AWD, S AWD, Touring AWD | 6 Cyl 3.6L
- 2005-2013 Chrysler 300 | Base AWD, C AWD, C John Varvatos AWD, C Luxury Series AWD, Limited AWD, S AWD, S V6 AWD, S V8 AWD, Touring AWD | 6 Cyl 3.5L, 6 Cyl 3.6L, 8 Cyl 5.7L
View related parts
Chrysler 300 Axle Half Shaft
Part Number: R4578600AA
$245.20 MSRP: $295.00
You Save: $49.80 (17%)
ADD TO CART
Product Specifications
- Other Name: Shaft-Axle Half; Axle Assembly
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2005-2019 Chrysler 300 | Base AWD, C AWD, C John Varvatos AWD, C Luxury Series AWD, C Platinum AWD, Limited AWD, S AWD, S V6 AWD, S V8 AWD, Touring AWD | 6 Cyl 3.5L, 6 Cyl 3.6L, 8 Cyl 5.7L
View related parts
Chrysler 300 Axle Half Shaft
Part Number: 52123952AD
$356.35 MSRP: $542.00
You Save: $185.65 (35%)
ADD TO CART
Product Specifications
- Other Name: Shaft-Axle Half; Axle Assembly
- Replaces: 52123952AA, 52123952AB, 52123952AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2015-2017 Chrysler 300 | C Platinum RWD, C RWD, Limited RWD, S RWD | 6 Cyl 3.6L
View related parts
Chrysler 300 Shaft-Axle Half
Part Number: 4578600AB
$433.12 MSRP: $664.00
You Save: $230.88 (35%)
ADD TO CART
Product Specifications
- Other Name: Axle Assembly, Drive Axle
- Position: Passenger Side
- Replaces: 4578600AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2005-2023 Chrysler 300 | Base AWD, C AWD, C John Varvatos AWD, C Luxury Series AWD, C Platinum AWD, Limited AWD, S AWD, S V6 AWD, S V8 AWD, Touring AWD | 6 Cyl 3.5L, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.6L, 8 Cyl 5.7 L GAS, 8 Cyl 5.7L, 8 Cyl 6.4 L GAS
View related parts
Chrysler 300 Axle Half Shaft
Part Number: 4578732AC
$526.85 MSRP: $797.00
You Save: $270.15 (34%)
ADD TO CART
Product Specifications
- Other Name: Shaft-Axle Half
- Replaced by: 4578732AE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2010 Chrysler 300 | C SRT8 RWD, Touring RWD | 8 Cyl 6.1L
View related parts
Chrysler 300 Axle Half Shaft
Part Number: 4726011AA
$388.25 MSRP: $593.00
You Save: $204.75 (35%)
ADD TO CART
Product Specifications
- Other Name: Shaft-Axle Half
- Replaced by: 4726011AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2013 Chrysler 300 | Base RWD, C John Varvatos RWD, C Luxury Series RWD, C RWD, C SRT8 RWD, Limited RWD, S RWD, S V6 RWD, S V8 RWD, SRT Core RWD, SRT Premium RWD | 6 Cyl 3.6L, 8 Cyl 5.7L, 8 Cyl 6.4L
View related parts
Chrysler 300 Axle Half Shaft Left
Part Number: 68080381AA
$364.05 MSRP: $554.00
You Save: $189.95 (35%)
ADD TO CART
Product Specifications
- Other Name: Shaft-Axle Half; Axle Assembly
- Position: Driver Side
- Replaces: 52123883AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2014 Chrysler 300 | Base RWD, C John Varvatos RWD, C Luxury Series RWD, C RWD, C SRT8 RWD, Limited RWD, S Luxury Series RWD, S RWD, S V6 RWD, S V8 RWD, SRT Core RWD, SRT Premium RWD | 6 Cyl 3.6L, 8 Cyl 5.7L, 8 Cyl 6.4L
View related parts
Chrysler 300 Axle Half Shaft
Part Number: 5180495AB
$530.15 MSRP: $802.00
You Save: $271.85 (34%)
ADD TO CART
Product Specifications
- Other Name: Shaft-Axle Half
- Replaced by: 5180495AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009 Chrysler 300 | C AWD, Limited AWD, Touring AWD | 6 Cyl 3.5L
View related parts
Chrysler 300 Rear-Axle Assembly Or Cv Shaft
Part Number: 4726009AA
$367.35 MSRP: $559.00
You Save: $191.65 (35%)
ADD TO CART
Product Specifications
- Other Name: Shaft-Axle Half; Axle Assembly
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2014 Chrysler 300 | Base RWD, C John Varvatos RWD, C Luxury Series RWD, C RWD, C SRT8 RWD, Limited RWD, S Luxury Series RWD, S RWD, S V6 RWD, S V8 RWD, SRT Core RWD, SRT Premium RWD | 6 Cyl 3.6L, 8 Cyl 5.7L, 8 Cyl 6.4L
View related parts
Chrysler 300 Axle Half Shaft Right
Part Number: 4726011AB
$388.25 MSRP: $593.00
You Save: $204.75 (35%)
ADD TO CART
Product Specifications
- Other Name: Shaft-Axle Half; Axle Assembly
- Replaces: 4726011AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2014 Chrysler 300 | Base RWD, C John Varvatos RWD, C Luxury Series RWD, C RWD, C SRT8 RWD, Limited RWD, S Luxury Series RWD, S RWD, S V6 RWD, S V8 RWD, SRT Core RWD, SRT Premium RWD | 6 Cyl 3.6L, 8 Cyl 5.7L, 8 Cyl 6.4L
View related parts
Chrysler 300 Axle Shaft Rear Right
Part Number: R8154332AA
$204.53 MSRP: $244.00
You Save: $39.47 (17%)
ADD TO CART
Product Specifications
- Other Name: Shaft-Axle Half
- Position: Rear Passenger Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2010 Chrysler 300 | Base RWD, C RWD, Limited RWD, LX RWD, S V6 RWD, Touring Plus RWD, Touring RWD | 6 Cyl 2.7L, 6 Cyl 3.5L
View related parts
Chrysler 300 Axle Half Shaft Right
Part Number: 5180492AC
$519.75 MSRP: $759.00
You Save: $239.25 (32%)
Product Specifications
- Other Name: Shaft-Axle Half; Axle Assembly
- Position: Passenger Side
- Replaces: 5180492AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009-2014 Chrysler 300 | Base AWD, C AWD, C John Varvatos AWD, C Luxury Series AWD, Limited AWD, S AWD, S V6 AWD, S V8 AWD | 6 Cyl 3.6L, 8 Cyl 5.7L

| Page 1 of 4 |Next >

1-20 of 72 Results

Chrysler 300 Axle Shaft

In Chrysler 300 cars, the Axle Shaft is critical in transmitting power from the differential to the driving wheels hence allowing independent rotation to improve tractions during turning. Usually made from steel, these axle shafts are always in sets and are fundamental in matters concerning positioning of wheels and bearing of weight applied on them. Chrysler 300 models have incorporated different axle shafting patterns including the live axle and the independent suspension. Live axle suspensions have rigid metal rods while, independent suspension systems use shafts with CVJ's in that the wheels do not have to be in fixed positions. While the latter offers dynamic benefits the firmness and solidity may be traded off for they are susceptible to CV joints and the shafts are exposed to worry some tough roads. In general, the Axle Shaft plays an important role in the necessary performance and maneuverability of Chrysler 300 automobiles.

Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Chrysler 300 Axle Shaft at great affordable prices. Moreover, all genuine Chrysler 300 Axle Shaft come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.

Chrysler 300 Axle Shaft Parts Questions & Experts Answers

Axle Half Shaft
4578732AB
Q: How to replace a drive axle boot and Axle Shaft on Chrysler 300?
A: If a Axle Shaft boot has failed, the entire shaft assembly must be replaced as boots are not serviceable separately. To remove, start by removing the wheel cover or hub cap and break the Axle Shaft/hub nut loose with a socket and large breaker bar. Block the front wheels to prevent the vehicle from rolling. Loosen the wheel lug nuts, raise the rear of the vehicle, and support it securely on jack stands. Remove the wheel. Remove the Axle Shaft/hub nut and discard it. Drain the gear lubricant from the Differential. Disconnect the driveshaft from the differential and remove the rear exhaust pipe and muffler. Pry the inner CV joint out of the differential just far enough to release the snap-ring. The Axle Shaft can't be removed from the differential until the differential has been lowered. Support the differential with a floor jack. Remove the mounting fasteners securing the differential to the crossmember and differential mount. Carefully lower the differential enough to separate the Axle Shaft(s) from the differential. Pull the Axle Shaft out of the hub flange. If it sticks, tap it out with a soft-faced hammer. Installation is the reverse of removal, noting the following points: Remove the rubber isolation washer from the outer CV joint stub shaft and inspect it. Replace it if necessary. Tighten the differential mounting bolts to the torque. Install a new Axle Shaft/hub nut. Tighten the hub nut securely, but don't try to tighten it to the actual torque specification until you've lowered the vehicle to the ground. Fill the differential with the type and amount of lubricant specified. Install the wheels and lower the vehicle to the ground. Tighten the wheel lug nuts to the torque. Tighten the Axle Shaft/hub nut to the torque. Install the wheel cover or hub cap.

Related Chrysler 300 Parts

Browse by Year

2023 Axle Shaft 2022 Axle Shaft 2021 Axle Shaft 2020 Axle Shaft 2019 Axle Shaft 2018 Axle Shaft 2017 Axle Shaft 2016 Axle Shaft 2015 Axle Shaft 2014 Axle Shaft 2013 Axle Shaft 2012 Axle Shaft 2011 Axle Shaft 2010 Axle Shaft 2009 Axle Shaft 2008 Axle Shaft 2007 Axle Shaft 2006 Axle Shaft 2005 Axle Shaft