×
- Live Chat
- 1-888-511-3595
My Garage
My Account
Cart
Genuine Chrysler Town & Country Door Lock Cylinder
Door Lock Cylinder Tumbler- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
10 Door Lock Cylinders found
Chrysler Town & Country Cylinder-Door Lock
Part Number: 5139099AA$69.77 MSRP: $104.00You Save: $34.23 (33%)
Chrysler Town & Country Cylinder - Door Lock Uncoded
Part Number: 4720931$29.63 MSRP: $42.80You Save: $13.17 (31%)
Chrysler Town & Country Cylinder Lock-Door Lock Cylinder
Part Number: 4778149$10.16 MSRP: $14.70You Save: $4.54 (31%)
Chrysler Town & Country Cylinder Lock-Door Lock
Part Number: 5011040AA$59.05 MSRP: $87.30You Save: $28.25 (33%)
Chrysler Town & Country Door Lock Cylinder
The Chrysler Town & Country Door Lock Cylinder is a kind of lock mechanism installed at the front doors which control the lock and unlock of the car with the help of the car key. In that aspect, this mechanism guarantees the safety of the interior part of the car and simplicity to use it at the same time. With time the Door Lock Cylinder may deteriorate because of frequent use hence leading to difficult in locking or unlocking the doors plus having a stuck key. Contrary to most contemporary automobiles, the Chrysler Town & Country car models come equipped with the conventional Door Lock Cylinders as their key component. For the Chrysler Town and Country drivers, the Door Lock Cylinder should be checked often and replaced immediately it is showing signs of wear out or any complications.
Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Chrysler Town & Country Door Lock Cylinder at great affordable prices. Moreover, all genuine Chrysler Town & Country Door Lock Cylinder come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.
Chrysler Town & Country Door Lock Cylinder Parts Questions & Experts Answers
- Q: How do you replace the door latch,Door Handle and Door Lock Cylinder on Chrysler Town & Country?A: To replace the front door latch, shut the window fully and then, pop off the front door trim panel, lift up the plastic water shield to get to the inner door hardware. If reinforced with power door locks, the wire connector has to be disconnected from the power door lock motor. Remove the clips which fasten the linkage to the door latch and then the linkages then the screws mounting the door latch to the door end frame then take out the latch. Removal is the exact opposite of installation though one is advised to use new screws if the latch has been removed. When completed with the installation of the door latch by using new screws, slide in the linkage into the latch and engage the clips and if their is electrical connector reconnect it. For the outside handle, the initial steps as with the inside handle to reach the inside of the door release mechanism, and disconnect switch connector in case your car came with Vehicle Theft Security System, and release the push in fasteners. Take out the handle to the outer panel by taking out the latch and lock linkages from the handle. In the outside handle for the lock cylinder you will need to pop of a clip then pull it out then you will need to install the new lock cylinder retaining clip and position the link arm before pushing the lock cylinder back in. For the sliding door latch/lock control, it is necessary to remove the trim panel of the sliding door, disconnect the external cable given in the figure, and also remove the foam insulation block given in the figure. Remove the inside latch handle and free the clip where the inside door handle bell crank link was previously fixed, also use bolts to take off the latch/lock control from the sliding door. For the outside handle of the sliding door, the procedure is almost similar to the internal handle to gain access to the handle. For the liftgate latch, the trim panel and watershield must be pulled off, the connection of the outside lock cylinder link and wire connector have to be disconnected and the screws of the latch have to be loosened. The outside handle for the liftgate includes; removal of the trim panel, followed by the electrical connectors and finally the removal of mounting screws. Last but not least, to take out the liftgate lock cylinder, press the clip to release latch link, if there was an electrical connector, then disconnect it, then turn counterclockwise the plastic nut on the lock cylinder and remove it. To uninstall all the components the process is the exact opposite of installation.
Related Chrysler Town & Country Parts
Browse by Year
2016 Door Lock Cylinder 2015 Door Lock Cylinder 2014 Door Lock Cylinder 2013 Door Lock Cylinder 2012 Door Lock Cylinder 2011 Door Lock Cylinder 2010 Door Lock Cylinder 2009 Door Lock Cylinder 2008 Door Lock Cylinder 2006 Door Lock Cylinder 2005 Door Lock Cylinder 2004 Door Lock Cylinder 2003 Door Lock Cylinder 2002 Door Lock Cylinder 2001 Door Lock Cylinder 2000 Door Lock Cylinder 1999 Door Lock Cylinder 1998 Door Lock Cylinder 1997 Door Lock Cylinder 1996 Door Lock Cylinder 1995 Door Lock Cylinder 1994 Door Lock Cylinder 1993 Door Lock Cylinder 1985 Door Lock Cylinder 1984 Door Lock Cylinder