×
- Live Chat
- 1-888-511-3595
My Garage
My Account
Cart
Genuine Dodge Neon Water Pump
H2O Pump- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
6 Water Pumps found
Dodge Neon Engine Cooling Water Pump
Part Number: 4667660AE$62.42 MSRP: $136.00You Save: $73.58 (55%)
Dodge Neon Engine Cooling Water Pump
Part Number: 4884159AA$88.02 MSRP: $134.00You Save: $45.98 (35%)
Dodge Neon Water Pump
The Water Pump in Dodge Neon vehicles aids in the circulation of coolant through the water jacket to extract heat produced by combustion and for regulating engine temperature. Contemporary versions of water pumps are metallic, more specifically, aluminum; the moving part included in the construction is the rotating shaft with an impeller to take the coolant along for the ride. Probable symptoms of a failing water pump include leaks which are common especially if the pump is not well sealed, noise from the bearings especially if they are worn out and overheating. There are high performance water pumps for high-revving engines that provide a higher flow rate for the coolant and less power demand. Electric water pumps must also be considered, which include advantages such as the coolant circulation and post shutdown cooling. Keeping a proper schedule of maintenance, and timely repair of parts that are worn out also needs to be put into consideration so as to avoid having to deal with a very expensive engine.
Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Dodge Neon Water Pump at great affordable prices. Moreover, all genuine Dodge Neon Water Pump come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.
Dodge Neon Water Pump Parts Questions & Experts Answers
- Q: How Do You Replace a Water Pump on Dodge Neon?A: Disconnect the cable from the negative battery terminal. Drain the cooling system. Remove the accessory drivebelts. Remove the timing belt cover, timing belt, timing belt tensioner, and rear timing belt cover. Remove the bolts attaching the water pump to the engine block and remove the pump from the engine. Clean the bolt threads and threaded holes in the engine to remove corrosion and sealant. Compare the new pump to the old one to ensure they are identical. Install a new O-ring seal in the groove that lines the water pump body and apply a thin film of RTV sealant to hold the seal in place during installation. Carefully mate the pump to the engine. Install the water pump bolts and tighten them to the specified torque. The remainder of the installation is the reverse of removal. Refill the cooling system and check for leaks after running the engine.
- Q: How Can You Check the Operation of a Water Pump on Dodge Neon?A: A failure in the water pump can cause serious engine damage due to overheating. There are three ways to check the operation of the water pump while it's installed on the engine. If the pump is defective, it should be replaced with a new or rebuilt unit. Water pumps are equipped with weep or vent holes. If a failure occurs in the pump seal, coolant will leak from the hole. In most cases, you'll need a flashlight to find the hole on the water pump from underneath to check for leaks. Some small black staining around the weep hole is normal. If the stain is heavy brown or actual coolant is evident, replace the pump. If the water pump shaft bearings fail, there may be a howling sound at the front of the engine while it's running. With the engine off, shaft wear can be felt if the water pump pulley is rocked up-and-down. Don't mistake drivebelt slippage, which causes a squealing sound, for water pump bearing failure. A quick water pump performance check is to put the heater on. If the pump is failing, it won't be able to efficiently circulate hot water all the way to the Heater Core as it should.
