×
- Live Chat
- 1-888-511-3595
My Garage
My Account
Cart
Genuine Dodge Ram 2500 Ignition Coil
Ignition Coil Resistor- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
18 Ignition Coils found
Dodge Ram 2500 Ignition Coil Compatible
Part Number: 56028138AD$54.94 MSRP: $82.00You Save: $27.06 (33%)
Dodge Ram 2500 Ignition Coil
The Ignition Coil as installed in Dodge Ram 2500 vehicles is Competition for converting the low voltage from the battery into the high voltage required to fire the air/fuel mixture in the cylinder. This is the link between the primary and secondary circuits where; the primary circuit embraces the battery, the ignition switch and the triggering device while the second circuit comprises the high tension lead and distributor cap. Dodge Ram 2500 Ignition Coils are made up of an insulated copper primary and secondary coil wrapped round an iron core, around which is a housing of plastic, epoxy, or polymer. The various ignition systems that has been used on Ram 2500 models in the past include the breaker point, the electronic distributor, the coil-on-plug and the wasted spark; all delivering voltage in different ways to the spark plugs in the vehicles. An Ignition Coil that is not functioning right can cause your engine to misfire, poor fuel efficiency and loss of power; therefore is important to check on it for a smooth running of the vehicle.
Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Dodge Ram 2500 Ignition Coil at great affordable prices. Moreover, all genuine Dodge Ram 2500 Ignition Coil come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.
Dodge Ram 2500 Ignition Coil Parts Questions & Experts Answers
- Q: How to Check the Ignition Coil on Dodge Ram 2500?A: To check the 3.7L V6 and 4.7L V8 engines, start by removing the ignition coil and cleaning the outer case for any damage. Clean the coil primary terminals and check for corrosion. Use an ohm-meter to measure the primary resistance across the two terminals of the connector. Compare the measurement to the specified range and replace the ignition coil if necessary. To check the secondary resistance, connect one ohm-meter lead to the positive terminal of the connector and the other lead to the high-tension terminal at the coil and the spark plug wire terminal. Compare the measurements to the specified range and replace the ignition coil if needed. If the resistance values are within range but the coil is still misfiring or causing trouble codes, try swapping it with an adjacent coil. If the issue persists, consult a professional. For the 3.6L V6 and HEMI engines, follow similar steps but note that for HEMI engines, it may be easier to check certain coils on the bench. Clean the outer case and terminals, measure the primary resistance, and swap coils if necessary. For replacement, remove the necessary components, disconnect the electrical connector, and remove the ignition coil. Install the new coil by reversing the removal steps.
Related Dodge Ram 2500 Parts
Dodge Ram 2500 Battery Cable
Dodge Ram 2500 Air Filter
Dodge Ram 2500 Ignition Switch
Dodge Ram 2500 Ignition Control Module
Dodge Ram 2500 Battery Tray
Dodge Ram 2500 Distributor
Dodge Ram 2500 Ignition Lock Assembly
Dodge Ram 2500 Battery Terminal
Dodge Ram 2500 Car Batteries
Dodge Ram 2500 Distributor Cap
Browse by Year
2010 Ignition Coil 2009 Ignition Coil 2008 Ignition Coil 2007 Ignition Coil 2006 Ignition Coil 2005 Ignition Coil 2004 Ignition Coil 2003 Ignition Coil 2002 Ignition Coil 2001 Ignition Coil 2000 Ignition Coil 1999 Ignition Coil 1998 Ignition Coil 1997 Ignition Coil 1996 Ignition Coil 1995 Ignition Coil 1994 Ignition Coil