Mopar 56029129AB Ignition Coil

You can Select Your Vehicle to check if 56029129AB fits your vehicle.

To check the 3.7L V6 and 4.7L V8 engines' ignition coils, begin by removing the coil and cleaning the outer case. For the HEMI engine, clean the outer case, primary terminals, and high-tension terminal. Check the primary resistance and replace it if not within range. To replace, remove the air intake duct, resonator box, and disconnect the electrical connector, remove the coil mounting bolts. To reinstall, switch the removal steps going from the final step to the beginning step.

To check the 3.7L V6 and 4.7L V8 engines, start by removing the ignition coil and cleaning the outer case for any damage. Clean the coil primary terminals and check for corrosion. Use an ohm-meter to measure the primary resistance across the two terminals of the connector. Compare the measurement to the specified range and replace the ignition coil if necessary. To check the secondary resistance, connect one ohm-meter lead to the positive terminal of the connector and the other lead to the high-tension terminal at the coil and the spark plug wire terminal. Compare the measurements to the specified range and replace the ignition coil if needed. If the resistance values are within range but the coil is still misfiring or causing trouble codes, try swapping it with an adjacent coil. If the issue persists, consult a professional. For the 3.6L V6 and HEMI engines, follow similar steps but note that for HEMI engines, it may be easier to check certain coils on the bench. Clean the outer case and terminals, measure the primary resistance, and swap coils if necessary. For replacement, remove the necessary components, disconnect the electrical connector, and remove the ignition coil. Install the new coil by reversing the removal steps.

Remove the air intake duct or upper intake manifold, disconnect the electrical connector from the coil, remove the mounting screw, and pull off the coil.

Remove the air intake duct or upper intake manifold, disconnect the electrical connector from the coil, remove the mounting screw, and pull off the coil.

If damage is found on a coil, it should be replaced.

First, disconnect the electrical connector from the coil. Then, remove the ignition coil mounting bolt.

When inspecting the coils, one should check for cracks, damage, and carbon tracking.

You should clean the coils with a dampened cloth and make sure to dry them thoroughly.

You should clean the coils with a dampened cloth and make sure to dry them thoroughly.

Remove the engine cover and disconnect the electrical connector and spark plug wire boot for the companion cylinder. Remove the coil mounting bolts and carefully pull up with a twisting motion to disengage the rubber spark plug boots. Inspect the condition of the rubber spark plug boot and replace if necessary.

Follow similar steps but note that for HEMI engines, it may be easier to check certain coils on the bench. Clean the outer case and terminals, measure the primary resistance, and swap coils if necessary. For replacement, remove the necessary components, disconnect the electrical connector, and remove the ignition coil. Install the new coil by reversing the removal steps.

It should be ensured that the coil fits securely onto the spark plug(s).

Start by removing the ignition coil and cleaning the outer case for any damage. Clean the coil primary terminals and check for corrosion on the coil tower terminal, cleaning it with a wire brush if necessary. Use an ohmmeter to measure the coil primary resistance by attaching the leads to the two terminals of the connector. Compare the measured resistance to the specified range and replace the ignition coil if it falls outside the range. To check the coil secondary resistance, connect one ohmmeter lead to the positive terminal of the connector and the other lead to the high-tension terminal. Compare the measured resistance to the specified range and replace the ignition coil if necessary. If the primary and secondary resistance values are within specification but the coil is still misfiring or causing trouble codes, try swapping it with an adjacent coil. If the issue persists, consult a professional for further testing.

Follow similar steps but note that for HEMI engines, it may be easier to check certain coils on the bench. Clean the outer case and terminals, measure the primary resistance, and swap coils if necessary. For replacement, remove the necessary components, disconnect the electrical connector, and remove the ignition coil. Install the new coil by reversing the removal steps.

Follow similar steps but note that for HEMI engines, it may be easier to check certain coils on the bench. Clean the outer case and terminals, measure the primary resistance, and swap coils if necessary. For replacement, remove the necessary components, disconnect the electrical connector, and remove the ignition coil. Install the new coil by reversing the removal steps.

Start by removing the ignition coil and cleaning the outer case for any damage. Clean the coil primary terminals and check for corrosion. Use an ohm-meter to measure the primary resistance across the two terminals of the connector. Compare the measurement to the specified range and replace the ignition coil if necessary. To check the secondary resistance, connect one ohm-meter lead to the positive terminal of the connector and the other lead to the high-tension terminal at the coil and the spark plug wire terminal. Compare the measurements to the specified range and replace the ignition coil if needed. If the resistance values are within range but the coil is still misfiring or causing trouble codes, try swapping it with an adjacent coil. If the issue persists, consult a professional.