×
- Live Chat
- 1-888-511-3595
My Garage
My Account
Cart
Genuine Dodge Ram 2500 Steering Knuckle
Front Steering Knuckle- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
21 Steering Knuckles found
Dodge Ram 2500 Front Steering Knuckle
Part Number: 5086678AA$566.53 MSRP: $869.00You Save: $302.47 (35%)
Dodge Ram 2500 Front Steering Knuckle
Part Number: 68032004AD$550.62 MSRP: $806.00You Save: $255.38 (32%)
Dodge Ram 2500 Front Steering Knuckle
Part Number: 68032003AA$570.00 MSRP: $834.00You Save: $264.00 (32%)
Dodge Ram 2500 Front Steering Knuckle
Part Number: 68032003AD$570.00 MSRP: $834.00You Save: $264.00 (32%)
| Page 1 of 2 |Next >
1-20 of 21 Results
Dodge Ram 2500 Steering Knuckle
The Steering Knuckle of Dodge Ram 2500 vehicles is essentially important framework between the suspension and steering that links the front wheels. It contains the upper control arm, lower control arm, the tie rods and the spindle or hubs which afford the vehicle to move vertically due to road surface irregularities and horizontally for the purpose of steering. The Steering Knuckle design in the Dodge Ram 2500 is a number of and is depending on the rear-wheel arrangement as well as the four-wheel arrangement. Possible, the RWD models have an integral spindle, moreover the 4WD have a hollow one that enables the drive axle to go through the Steering Knuckle. Kinstogs and modern ball joints have been used in the Dodge Ram 2500 over the years and the changes actually depict the advancement in looks. Steering Steering Knuckles are quite strong but they can be replaced if they are worn out or if other parts employed with the Steering Knuckles such as bearings, ball joints or tie-rod ends become damaged. Therefore, it is required to periodically check the condition of the Steering Knuckle and spindle for achieving the premier result when driving a Dodge Ram 2500 and minimizing the risks.
Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Dodge Ram 2500 Steering Knuckle at great affordable prices. Moreover, all genuine Dodge Ram 2500 Steering Knuckle come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.
Dodge Ram 2500 Steering Knuckle Parts Questions & Experts Answers
- Q: How to Remove and Install a Steering Knuckle on Dodge Ram 2500?A: Loosen the wheel lug nuts, raise the vehicle and support it securely on jackstands. Remove the wheel. On 4WD models, unscrew the driveaxle/hub nut with a socket and large breaker bar. Brace a large prybar across two of the wheel studs or insert a large screwdriver through the center of the brake caliper and into the disc cooling vanes to prevent the hub from turning as the nut is loosened. Remove the disc brake caliper and disc. If equipped, disconnect the electrical connector from the wheel speed sensor and remove the sensor. Disconnect the tie-rod from the steering knuckle. Remove the driveaxle/hub nut. Support the lower Control Arm with a floor jack. Separate the lower control arm from the steering knuckle. Separate the upper control arm from the steering knuckle. Remove the knuckle. Carefully inspect the steering knuckle for cracks, especially around the steering arm and spindle mounting area. Also inspect the balljoint stud holes. if they're elongated, or if you find any cracks in the knuckle, replace the steering knuckle. Installation is the reverse of removal. Tighten all suspension fasteners. Loosen the wheel lug nuts, raise the vehicle and support it securely on jackstands. Remove the wheel. Remove the hub bearing and axle shaft. Disconnect the tie-rod end or drag link from the steering knuckle. Remove the wheel speed sensor. Loosen the steering knuckle upper ballstud nut a few turns, but don't remove it. Remove the lower balljoint nut. Use a balljoint separation tool to detach the balljoint from the knuckle. Remove the upper balljoint nut. Separate the steering knuckle. Use a brass hammer to knock it loose if necessary. Installation is the reverse of removal. Tighten all suspension fasteners.
Related Dodge Ram 2500 Parts
Browse by Year
2010 Steering Knuckle 2009 Steering Knuckle 2008 Steering Knuckle 2007 Steering Knuckle 2006 Steering Knuckle 2005 Steering Knuckle 2004 Steering Knuckle 2003 Steering Knuckle 2002 Steering Knuckle 2001 Steering Knuckle 2000 Steering Knuckle 1999 Steering Knuckle 1998 Steering Knuckle 1997 Steering Knuckle 1996 Steering Knuckle 1995 Steering Knuckle 1994 Steering Knuckle