How do you remove and install the rocker arms and shaft in 3.9L V6 engine on Dodge Ramcharger?

Incase of removal and installation of the rocker arms and shaft one is required to first drop the rocker arm. Fourth, disconnect the rocker arm shaft by unscrewing four bolts and retainers of the engine part. Raise both the rocker arm shaft and the two rocker arms as one piece. If some of the rocker arms are to be replaced, simply slide off any rocker arms that may be on the shaft. During reassembly, make sure that the rocker arms are assembled into the left and right sets since the intake and exhaust side rocker arms are different, thanks to the 4-bolt shaft and, therefore, must be assembled in a particular sequence. The rocker arm and shaft assembly is now fitted with the aid of the notch that is provided at the end of the shaft in line with the center line of the engine with the left head front and the right head back. The rocker arm shaft retainers are of different lengths, ensure that the long ones are fitted in the second and fourth position. Progressively increase the torque applied on the rocker arm shaft bolts beginning with the centre bolt to the appropriate torque figure; the lifter needs 20 minutes bleed time after installation before the engine is started. Finally add back the rocker arm cover(s) if you pulled it/them off.

Genuine Dodge Ramcharger Rocker Arm

Engine Rocker Arm

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

4 Rocker Arms found

View related parts
Dodge Ramcharger Pivot Rocker Arm
Part Number: 53008283
$19.35
ADD TO CART
Product Specifications
- Other Name: Arm-Rocker Arm; Rocker Pivot
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1992-1993 Dodge Ramcharger | Sport Utility 2WD, Sport Utility 4WD | 8 Cyl 5.2L, 8 Cyl 5.9L
View related parts
Dodge Ramcharger Engine Rocker Arm Kit
Part Number: 53008282
$32.06 MSRP: $47.50
You Save: $15.44 (33%)
ADD TO CART
Product Specifications
- Other Name: Rocker Arm Valve; Rocker Arm
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1992-1993 Dodge Ramcharger | Sport Utility 2WD, Sport Utility 4WD | 8 Cyl 5.2L, 8 Cyl 5.9L
View related parts
Dodge Ramcharger Rocker Valve Right
Part Number: 4448994
$16.90 MSRP: $21.50
You Save: $4.60 (22%)
ADD TO CART
Product Specifications
- Other Name: Rocker, Valve, Rt.; Rocker Arm
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1988-1992 Dodge Ramcharger | Sport Utility 2WD, Sport Utility 4WD | 6 Cyl 3.9L, 8 Cyl 5.2L, 8 Cyl 5.9L
View related parts
Dodge Ramcharger Arm-Exhaust
Part Number: 4429910
Product Specifications
- Other Name: Lever, Rocker Exhaust; Exhaust Rocker Arm
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1989-1993 Dodge Ramcharger | Sport Utility 2WD, Sport Utility 4WD | 6 Cyl 5.9L Diesel

Dodge Ramcharger Rocker Arm

Rocker Arm is an important part of the valvetrain system of the engines used in Dodge Ram charger cars where it provides the transferring motion for the Pushrod to Intake and Exhaust valves. Usually fabricated from stamped steel or aluminum, these rocker arms transform the vertical movement of the pushrod into the amount of downward push to open the valves. For high RPM engines, aluminum material is ideal for the lightweight nature Mals because the strength while cast iron or forged carbon steel is ideal especially in the manufacturing of diesel engines. Traditional and roller types of Rocker Arms may be installed in Dodge Ramcharger models. Unlike traditional rocker arms, roller rockers utilise needle bearings thus implying lesser friction and wear, which makes them better suited for performance. The rocker ratio which is between 1.5:1 and 1.8:1 on todays engines can increase camshaft lift hence enhancing the general performance of the engine. There is also use of modified fulcrum bearings especially in Dodge Ramcharger engines with higher RPM for better stress management and durability.

Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Dodge Ramcharger Rocker Arm at great affordable prices. Moreover, all genuine Dodge Ramcharger Rocker Arm come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.

Dodge Ramcharger Rocker Arm Parts Questions & Experts Answers

Engine Rocker Arm Kit
53008282
Q: How do you remove and install the rocker arms and shaft in 3.9L V6 engine on Dodge Ramcharger?
A: Incase of removal and installation of the rocker arms and shaft one is required to first drop the rocker arm. Fourth, disconnect the rocker arm shaft by unscrewing four bolts and retainers of the engine part. Raise both the rocker arm shaft and the two rocker arms as one piece. If some of the rocker arms are to be replaced, simply slide off any rocker arms that may be on the shaft. During reassembly, make sure that the rocker arms are assembled into the left and right sets since the intake and exhaust side rocker arms are different, thanks to the 4-bolt shaft and, therefore, must be assembled in a particular sequence. The rocker arm and shaft assembly is now fitted with the aid of the notch that is provided at the end of the shaft in line with the center line of the engine with the left head front and the right head back. The rocker arm shaft retainers are of different lengths, ensure that the long ones are fitted in the second and fourth position. Progressively increase the torque applied on the rocker arm shaft bolts beginning with the centre bolt to the appropriate torque figure; the lifter needs 20 minutes bleed time after installation before the engine is started. Finally add back the rocker arm cover(s) if you pulled it/them off.