Where is the Throttle Position Sensor Located on Jeep Liberty?

The throttle position sensor is located on the throttle body at the end of the throttle shaft. It monitors the output voltage to determine fuel delivery based on throttle valve angle. A broken or loose sensor can cause fuel bursts and an unstable idle. To remove the sensor, first remove the air intake duct/resonator. Then, disconnect the electrical connector from the sensor. On newer models, there is only one large electrical connector at the throttle body. Remove the mounting screws and take out the sensor. When installing the sensor, align the socket locating tangs with the throttle shaft and apply slight tension. If needed, install the sensor with the tangs on the other side of the shaft. The rest of the installation is the reverse of removal.

Genuine Jeep Liberty Throttle Position Sensor

TPS Switch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

3 Throttle Position Sensors found

View related parts
Jeep Liberty Throttle Position Sensor Kit
Part Number: 5019411AB
$97.00 MSRP: $136.00
You Save: $39.00 (29%)
ADD TO CART
Product Specifications
- Other Name: Sensor-Throttle Position
- Replaced by: 68404428AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2002-2004 Jeep Liberty | Limited Edition 2WD, Limited Edition 4WD, Renegade 2WD, Renegade 4WD, Sport 2WD, Sport 4WD | 4 Cyl 2.4L, 6 Cyl 3.7L
View related parts
Jeep Liberty Throttle Position Sensor Kit
Part Number: 5019411AC
$89.24 MSRP: $136.00
You Save: $46.76 (35%)
ADD TO CART
Product Specifications
- Other Name: Sensor-Throttle Position
- Replaced by: 68404428AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2005-2006 Jeep Liberty | Limited Edition 2WD, Limited Edition 4WD, Renegade 2WD, Renegade 4WD, Sport 2WD, Sport 4WD | 4 Cyl 2.4L, 6 Cyl 3.7L
View related parts
Jeep Liberty Throttle Position Sensor
Part Number: 4874371AD
Product Specifications
- Other Name: Sensor-Throttle Position
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2002-2003 Jeep Liberty | Sport 2WD, Sport 4WD | 4 Cyl 2.4L

Jeep Liberty Throttle Position Sensor

The Throttle Position Sensor is an important component especially in the Jeep Liberty vehicles to regulate the flow of the air-fuel mixture for combustion. Thus monitoring the throttle position TPS sends signals to fuel injection system, by which the engine control unit can regulate the fuel delivery according to power demand. This feedback loop happens many times per second thus allowing for proper acceleration and deceleration. Jeep Liberty models employ modern contactless TPS solutions including Hall effect and magnetoresistive sensors while the old-fashioned potentiometric sensors are based on a direct contact. The non-contact design of the sensor offers a higher level of reliability and efficiency for instance in the electronic throttle control systems. Further, there are other accelerator pedal sensors like the wide open throttle (WOT) sensors that together with the TPS helps to improve the engine performance. Altogether, Throttle Position Sensor is an important component that helps in maintaining the performance and fuel consumption of Jeep Liberty vehicles.

Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Jeep Liberty Throttle Position Sensor at great affordable prices. Moreover, all genuine Jeep Liberty Throttle Position Sensor come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.

Jeep Liberty Throttle Position Sensor Parts Questions & Experts Answers

Throttle Position Sensor Kit
5019411AC
Q: Where is the Throttle Position Sensor Located on Jeep Liberty?
A: The throttle position sensor is located on the throttle body at the end of the throttle shaft. It monitors the output voltage to determine fuel delivery based on throttle valve angle. A broken or loose sensor can cause fuel bursts and an unstable idle. To remove the sensor, first remove the air intake duct/resonator. Then, disconnect the electrical connector from the sensor. On newer models, there is only one large electrical connector at the throttle body. Remove the mounting screws and take out the sensor. When installing the sensor, align the socket locating tangs with the throttle shaft and apply slight tension. If needed, install the sensor with the tangs on the other side of the shaft. The rest of the installation is the reverse of removal.