×
- Live Chat
- 1-888-511-3595
My Garage
My Account
Cart
Genuine Ram 1500 Brake Line
Brake Hose- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
122 Brake Lines found
| Page 1 of 7 |Next >
1-20 of 122 Results
Ram 1500 Brake Line
The Brake Line belongs to the hydraulic system in Ram 1500 vehicles, Its function is to transport brake fluid from the master cylinder to the brake caliper pistons. This is crucial in ensuring that the force applied at the brake pedal is translated into hydraulic pressure that aids the calipers to grip the rotors to help the car come to a stand still. Different types of Brake Line have been used in Ram 1500 over the years with emphasis on the security of the lines. Sealing of these lines have to be correct as any pin-pricks or formation of air bubbles in the line can compromise brake systems and potentially lead to brake failure. With this Brake Line design being an essential component needed for safe operation of the Ram 1500, its performance can not be overemphasized.
Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Ram 1500 Brake Line at great affordable prices. Moreover, all genuine Ram 1500 Brake Line come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.
Ram 1500 Brake Line Parts Questions & Experts Answers
- Q: How Should I Inspect and Replace Rubber Hoses Connecting Steel Brake Lines on Ram 1500?A: Whenever the vehicle is raised and supported securely on jackstands, inspect the rubber hoses that connect the steel brake lines with the front and rear brake assemblies for cracks, chafing of the outer cover, leaks, blisters, and other damage. These hoses are important and vulnerable parts of the brake system, so the inspection should be thorough. Use a light and mirror to assist in the check. If any hose exhibits any of the above conditions, replace it immediately. To replace the flexible hose, clean all dirt away from the hose fittings. Using a flare-nut wrench, disconnect the metal brake line from the hose fitting, being careful not to bend the frame bracket or line. If the threaded fitting is corroded, spray it with penetrating oil and allow it to soak in for about 10 minutes before trying again. If a fitting nut is frozen, do not force it as it will kink the metal line, which will then need to be replaced. Disconnect the brake hose bracket from the frame and immediately plug the metal line to prevent excessive leakage and contamination. Unscrew the banjo bolt at the caliper and remove the hose, discarding the sealing washers on either side of the fitting. Attach the new brake hose to the caliper, always using new sealing washers. Tighten the banjo bolt to the specified torque. Connect the other end of the new hose, ensuring it is not kinked or twisted. Fit the metal line to the hose or hose fitting, then tighten the hose bracket and the brake tube fitting nut securely. Check that the suspension or steering components do not make contact with the hose. Have an assistant push down on the vehicle while checking for interference with suspension operation. If replacing a front hose, have the assistant turn the steering wheel lock-to-lock while ensuring the hose does not interfere with the steering linkage or steering knuckle. After installation, bleed the brakes, check the master cylinder fluid level, and add fluid as necessary. Carefully test brake operation before returning the vehicle to normal service. When replacing brake lines, use the correct parts and avoid using copper tubing. Purchase steel brake lines from a dealer parts department or auto parts store. Prefabricated brake lines with flared tube ends and installed fittings are available. If bending a line is necessary, use a tubing bender to prevent kinking. When installing the new line, ensure it is well supported in the brackets and has sufficient clearance from moving or hot components. Tighten the fittings securely.
