How do you remove and install a door latch, handle and lock cylinder on Chrysler PT Cruiser?

To remove the latch, first take off the door trim panel, ensuring that on vehicles with electric windows, the window is closed before disconnecting the electrical connectors. For manual windows, install the window crank without the retaining clip and roll up the window. If removing a rear door latch, also remove the window glass lower rear run channel. Disconnect the lock cylinder, lock button, and latch release operating rods from the door latch, and for vehicles with central door locks, disconnect the electrical connector. Remove the three mounting screws from the end of the door and take out the door latch. For installation, position the latch, install and securely tighten the screws, then connect the operating rods to the latch and secure them with retaining clips. It is important not to close the door until the latch has been properly adjusted. To adjust, insert a Torx-head wrench through the elongated hole near the latch, engage it with the Torx-head screw inside the door latch linkage, and loosen it a couple of turns. Push the outside door handle all the way in and release it, then tighten the socket head screw on the door latch linkage and check the door operation. For the outside handle, remove the door trim panel, ensuring the window is closed for electric windows or rolling it up for manual ones. Disconnect the central locking electrical connector if equipped, detach the operating rod retaining clip and operating rod from the lock cylinder, remove the mounting nuts, and withdraw the handle from the door. Installation is the reverse of removal. For the lock cylinder, first remove the outside door handle, then detach the operating rod retaining clip and operating rod from the lock cylinder, disconnect the electrical connector if equipped, and pry off the lock cylinder retainer with a screwdriver to withdraw it from the door or handle. Installation is the reverse of removal.

Genuine Chrysler PT Cruiser Door Latch Assembly

Door Latch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

29 Door Latch Assemblys found

View related parts
Chrysler PT Cruiser Front Left (Driver-Side) Door Lock Actuator
Part Number: 5027961AB
$139.75 MSRP: $209.00
You Save: $69.25 (34%)
ADD TO CART
Product Specifications
- Other Name: Latch-Front Door
- Position: Front Driver Side
- Replaced by: 5027961AI
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2002 Chrysler PT Cruiser | Base, Limited, Touring | 4 Cyl 2.4L
View related parts
Chrysler PT Cruiser Door Lock Actuator
Part Number: 5027074AD
$78.23 MSRP: $163.00
You Save: $84.77 (53%)
ADD TO CART
Product Specifications
- Other Name: Latch-Rear Door
- Replaced by: 68268220AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2003-2008 Chrysler PT Cruiser | Base, GT, Limited, LX, Touring | 4 Cyl 2.4L
View related parts
Chrysler PT Cruiser Rear Passenger Side Door Latch
Part Number: 5027074AF
$78.23 MSRP: $163.00
You Save: $84.77 (53%)
ADD TO CART
Product Specifications
- Other Name: Latch-Rear Door
- Position: Rear Passenger Side
- Replaced by: 68268220AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009 Chrysler PT Cruiser | Base, Limited, Touring | 4 Cyl 2.4L
View related parts
Chrysler PT Cruiser Rear Door Latch
Part Number: 5027074AG
$78.23 MSRP: $163.00
You Save: $84.77 (53%)
ADD TO CART
Product Specifications
- Other Name: Latch-Rear Door
- Replaced by: 68268220AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2010 Chrysler PT Cruiser | Classic | 4 Cyl 2.4L
View related parts
Chrysler PT Cruiser Front Door Latch
Part Number: 5067137AB
$134.16 MSRP: $201.00
You Save: $66.84 (34%)
ADD TO CART
Product Specifications
- Other Name: Latch-Front Door
- Position: Front
- Replaced by: 5067137AF
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2004-2005 Chrysler PT Cruiser | Base, GT, Limited, Touring | 4 Cyl 2.4L
View related parts
Chrysler PT Cruiser Rear Door Latch
Part Number: 5027075AD
$108.89 MSRP: $163.00
You Save: $54.11 (34%)
ADD TO CART
Product Specifications
- Other Name: Latch-Rear Door
- Replaced by: 68266957AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2003-2008 Chrysler PT Cruiser | Base, GT, Limited, LX, Touring | 4 Cyl 2.4L
View related parts
Chrysler PT Cruiser Rear Door Latch
Part Number: 5027075AF
$108.89 MSRP: $163.00
You Save: $54.11 (34%)
ADD TO CART
Product Specifications
- Other Name: Latch-Rear Door
- Replaced by: 68266957AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009 Chrysler PT Cruiser | Base, Limited, Touring | 4 Cyl 2.4L
View related parts
Chrysler PT Cruiser Front Door Latch
Part Number: 5067137AD
$134.16 MSRP: $201.00
You Save: $66.84 (34%)
ADD TO CART
Product Specifications
- Other Name: Latch-Front Door
- Replaced by: 5067137AF
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2006-2008 Chrysler PT Cruiser | Base, GT, Limited, LX, Touring | 4 Cyl 2.4L
View related parts
Chrysler PT Cruiser Front Door Latch
Part Number: 5067137AE
$134.16 MSRP: $201.00
You Save: $66.84 (34%)
ADD TO CART
Product Specifications
- Other Name: Latch-Front Door
- Position: Front
- Replaced by: 5067137AF
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009-2010 Chrysler PT Cruiser | Base, Classic, Limited, Touring | 4 Cyl 2.4L
View related parts
Chrysler PT Cruiser Door Lock Actuator
Part Number: 5067308AC
$143.10 MSRP: $214.00
You Save: $70.90 (34%)
ADD TO CART
Product Specifications
- Other Name: Latch-Front Door
- Replaced by: 5067308AE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2006-2008 Chrysler PT Cruiser | Base Convertible, GT Convertible, Touring Convertible | 4 Cyl 2.4L
View related parts
Chrysler PT Cruiser Front Door Latch
Part Number: 5067309AC
$143.10 MSRP: $214.00
You Save: $70.90 (34%)
ADD TO CART
Product Specifications
- Other Name: Latch-Front Door
- Position: Front
- Replaced by: 5067309AE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2006-2008 Chrysler PT Cruiser | Base Convertible, GT Convertible, Touring Convertible | 4 Cyl 2.4L
View related parts
Chrysler PT Cruiser Door Lock Actuator
Part Number: 5067378AD
$108.63 MSRP: $161.00
You Save: $52.37 (33%)
ADD TO CART
Product Specifications
- Other Name: Latch-Front Door
- Replaced by: 5067378AF
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2006-2008 Chrysler PT Cruiser | Base, GT, Limited, LX, Touring | 4 Cyl 2.4L
View related parts
Chrysler PT Cruiser Front Door Latch
Part Number: 5067378AE
$108.63 MSRP: $161.00
You Save: $52.37 (33%)
ADD TO CART
Product Specifications
- Other Name: Latch-Front Door
- Position: Front
- Replaced by: 5067378AF
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009-2010 Chrysler PT Cruiser | Base, Classic, Limited, Touring | 4 Cyl 2.4L
View related parts
Chrysler PT Cruiser Front Right (Passenger-Side) Door Lock Actuator
Part Number: 5027960AB
$122.95 MSRP: $182.00
You Save: $59.05 (33%)
ADD TO CART
Product Specifications
- Other Name: Latch-Front Door
- Replaced by: 5027960AI
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2002 Chrysler PT Cruiser | Base, Limited, Touring | 4 Cyl 2.4L
View related parts
Chrysler PT Cruiser Front Door Latch
Part Number: 5067134AA
Product Specifications
- Other Name: Latch-Front Door
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2002-2003 Chrysler PT Cruiser | Base, GT, Limited, Touring | 4 Cyl 2.4L
View related parts
Chrysler PT Cruiser Front Door Latch
Part Number: 5067135AA
Product Specifications
- Other Name: Latch-Front Door
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2002-2003 Chrysler PT Cruiser | Base, GT, Limited, Touring | 4 Cyl 2.4L
View related parts
Chrysler PT Cruiser Front Right (Passenger-Side) Door Lock Actuator
Part Number: 5067136AA
Product Specifications
- Other Name: Latch-Front Door
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2002 Chrysler PT Cruiser | Base, Limited, Touring | 4 Cyl 2.4L
View related parts
Chrysler PT Cruiser Front Door Latch
Part Number: 5067137AA
Product Specifications
- Other Name: Latch-Front Door
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2002-2003 Chrysler PT Cruiser | Base, GT, Limited, Touring | 4 Cyl 2.4L
View related parts
Chrysler PT Cruiser Front Right (Passenger-Side) Door Lock Actuator
Part Number: 5067308AA
Product Specifications
- Other Name: Latch-Front Door
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2004-2005 Chrysler PT Cruiser | Base Convertible, GT Convertible, Touring Convertible | 4 Cyl 2.4L
View related parts
Chrysler PT Cruiser Front Door Latch
Part Number: 5067309AA
Product Specifications
- Other Name: Latch-Front Door
- Position: Front
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2004-2005 Chrysler PT Cruiser | Base Convertible, GT Convertible, Touring Convertible | 4 Cyl 2.4L

| Page 1 of 2 |Next >

1-20 of 29 Results

Chrysler PT Cruiser Door Latch Assembly

The Door Latch Assembly application is a critical component of Chrysler PT Cruiser automobiles as it locks the door to avoid people's interference with the vehicle interior. This assembly can therefore be operated either slowly by hand and locked and unlocked either individually or all at once from a central point. Different models of Chrysler PT Cruiser produce several styles of Door Latch Assembly throughout the years to produce lasting and efficient product. Some signs that you might need a replacement of the Door Latch Assembly includes if the outer door handles, the latches or the door lock button fail to operate as they are supposed to. The Chrysler PT Cruiser Door Latch Assembly should be serviced often so that the car remains safe and its door feature can work efficiently.

Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Chrysler PT Cruiser Door Latch Assembly at great affordable prices. Moreover, all genuine Chrysler PT Cruiser Door Latch Assembly come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.

Chrysler PT Cruiser Door Latch Assembly Parts Questions & Experts Answers

Front Left (Driver-Side) Door Lock Actuator
5027961AB
Q: How do you remove and install a door latch, handle and lock cylinder on Chrysler PT Cruiser?
A: To remove the latch, first take off the door trim panel, ensuring that on vehicles with electric windows, the window is closed before disconnecting the electrical connectors. For manual windows, install the window crank without the retaining clip and roll up the window. If removing a rear door latch, also remove the window glass lower rear run channel. Disconnect the lock cylinder, lock button, and latch release operating rods from the door latch, and for vehicles with central door locks, disconnect the electrical connector. Remove the three mounting screws from the end of the door and take out the door latch. For installation, position the latch, install and securely tighten the screws, then connect the operating rods to the latch and secure them with retaining clips. It is important not to close the door until the latch has been properly adjusted. To adjust, insert a Torx-head wrench through the elongated hole near the latch, engage it with the Torx-head screw inside the door latch linkage, and loosen it a couple of turns. Push the outside door handle all the way in and release it, then tighten the socket head screw on the door latch linkage and check the door operation. For the outside handle, remove the door trim panel, ensuring the window is closed for electric windows or rolling it up for manual ones. Disconnect the central locking electrical connector if equipped, detach the operating rod retaining clip and operating rod from the lock cylinder, remove the mounting nuts, and withdraw the handle from the door. Installation is the reverse of removal. For the lock cylinder, first remove the outside door handle, then detach the operating rod retaining clip and operating rod from the lock cylinder, disconnect the electrical connector if equipped, and pry off the lock cylinder retainer with a screwdriver to withdraw it from the door or handle. Installation is the reverse of removal.