How to Remove and Install a Fuel Pump/Fuel Pressure Regulator/Fuel Level Sending Unit Assembly on a Dodge Avenger?

All wheel drive (AWD) models have a saddle fuel tank configuration and have main and auxiliary fuel pumps. Each fuel pump has a sending unit. The auxiliary fuel pump contains the fuel pump reservoir, fuel pressure regulator and fuel filter. Relieve the fuel system pressure. Disconnect the negative battery cable from the remote ground terminal or battery. Remove the rear seat cushion and fuel pump module cover. On AWD models, remove main and auxiliary fuel pump module covers. Disconnect the fuel delivery line quick-connect fitting and on 2015 and later models, also disconnect the fuel vapor line from the fuel pump/fuel pressure regulator/Fuel Level Sensor assembly. Disconnect the electrical connector from the fuel pump/fuel pressure regulator/Fuel Level Sensor assembly. Before removing the fuel pump/fuel pressure regulator/Fuel Level Sensor assembly, make alignment marks on the assembly and the fuel tank (if marks don't already exist), to ensure the assembly will be correctly realigned when it's installed again. Using adjustable-joint pliers, loosen the lock ring that secures the fuel pump/fuel pressure regulator/Fuel Level Sensor assembly. Carefully lift the fuel pump/fuel pressure regulator/Fuel Level Sensor assembly from the fuel tank. Angle the module so that you don't bend the float arm of the Fuel Level Sensor or damage the fuel pump inlet strainer. If you're removing the auxiliary pump on an AWD model, raise the fuel pump module and disconnect the internal fuel line. While the pump is removed, inspect the pump inlet strainer. Make sure that it's not clogged or damaged. If the inlet strainer is dirty, try washing it in clean solvent. If it's still clogged, replace it. Installation is the reverse of removal. Line up the marks, and tighten the fuel pump module lock ring securely.

Genuine Dodge Avenger Fuel Level Sensor

Gas Gauge Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

12 Fuel Level Sensors found

View related parts
Dodge Avenger Level Unit Module Kit
Part Number: 68042937AA
$88.82 MSRP: $147.00
You Save: $58.18 (40%)
ADD TO CART
Product Specifications
- Other Name: Module-Level Unit; Fuel Gauge Sending Unit, Level Sensor
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2014 Dodge Avenger | Express, Heat, LUX, Mainstreet, R/T FWD, SE, SXT | 4 Cyl 2.4L
View related parts
Dodge Avenger Fuel Pump/Level Unit Module Kit
Part Number: 68138243AA
$518.10 MSRP: $789.00
You Save: $270.90 (35%)
ADD TO CART
Product Specifications
- Other Name: Modul Pkg-Fuel Pump/Level Unit
- Replaced by: 68138243AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2014 Dodge Avenger | Express, LUX, Mainstreet, R/T FWD, SE, SXT, SXT Plus | 6 Cyl 3.6L
View related parts
Dodge Avenger Fuel Pump Module Assembly
Part Number: 68033083AB
$321.20 MSRP: $490.00
You Save: $168.80 (35%)
ADD TO CART
Product Specifications
- Other Name: Module Kit Fuel Pump/Level Unit
- Replaced by: 68033083AF
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2014 Dodge Avenger | Express, Heat, LUX, Mainstreet, R/T FWD, SE, SXT | 4 Cyl 2.4L
View related parts
Dodge Avenger Level Unit Module Kit
Part Number: 68138245AA
$518.10 MSRP: $789.00
You Save: $270.90 (35%)
ADD TO CART
Product Specifications
- Other Name: Module-Level Unit
- Replaced by: 68138243AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011 Dodge Avenger | Express, LUX, Mainstreet, R/T FWD | 6 Cyl 3.6L
View related parts
Dodge Avenger Fuel Pump Module Assembly-And Level Sensor Module
Part Number: 68004936AC
$420.66 MSRP: $619.00
You Save: $198.34 (33%)
ADD TO CART
Product Specifications
- Other Name: Module Kit Fuel Pump/Level Unit
- Replaced by: 68004936AE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2010 Dodge Avenger | Express, Heat, R/T FWD, SE, SXT | 4 Cyl 2.4L, 6 Cyl 2.7L, 6 Cyl 3.5L
View related parts
Dodge Avenger Fuel Pump Module/Level Unit
Part Number: 68004475AB
$417.24 MSRP: $612.00
You Save: $194.76 (32%)
ADD TO CART
Product Specifications
- Other Name: Module Kit Fuel Pump/Level Unit
- Replaced by: 68004475AF
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2014 Dodge Avenger | SE, SXT | 4 Cyl 2.4L
- 2007-2011 Dodge Avenger | Express, Heat, LUX, Mainstreet, R/T FWD, SE, SXT | 4 Cyl 2.4L, 6 Cyl 2.7L, 6 Cyl 3.5L
View related parts
Dodge Avenger Fuel Pump Module Assembly-And Level Sensor Module
Part Number: RL004475AB
$417.24 MSRP: $612.00
You Save: $194.76 (32%)
ADD TO CART
Product Specifications
- Other Name: Module Kit Fuel Pump/Level Unit
- Replaced by: 68004475AF
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2012-2013 Dodge Avenger | LUX, SE, SXT | 4 Cyl 2.4L
View related parts
Dodge Avenger Level Unit Module Kit
Part Number: 68042934AB
Product Specifications
- Other Name: Module-Level Unit; Fuel Gauge Sending Unit, Level Sensor
- Replaces: 68042934AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2013 Dodge Avenger | Express, Heat, LUX, Mainstreet, R/T FWD, SE, SXT | 4 Cyl 2.4L, 6 Cyl 2.7L, 6 Cyl 3.5L
View related parts
Dodge Avenger Fuel Tank Level Unit
Part Number: MB863961
Product Specifications
- Other Name: Gauge Unit, Tank
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1995-1996 Dodge Avenger | Base, ES | 4 Cyl 2.0L, 6 Cyl 2.5L
View related parts
Dodge Avenger Fuel Gauge Sending Unit
Part Number: MR241078
Product Specifications
- Other Name: Gauge Unit, Fuel Tank; Gauge Unit
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1995-1998 Dodge Avenger | Base, ES | 4 Cyl 2.0L, 6 Cyl 2.5L
View related parts
Dodge Avenger Fuel Tank Sending Unit
Part Number: 68042934AA
Product Specifications
- Other Name: Level Unit Package Fuel
- Replaced by: 68042934AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007 Dodge Avenger | R/T FWD, SE, SXT | 4 Cyl 2.4L, 6 Cyl 2.7L, 6 Cyl 3.5L
View related parts
Dodge Avenger Fuel Level Unit
Part Number: 68042936AA
Product Specifications
- Other Name: Level Unit Package Fuel
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007 Dodge Avenger | R/T AWD | 6 Cyl 3.5L

Dodge Avenger Fuel Level Sensor

The Fuel Level Sensor in Dodge Avenger cars play the basic role of measuring the level of the fuel in the tank and giving the driver an indication of when to refill the tank. Its fast response system allows the device to provide accurate readings that oppose to sometimes taking a full tank indicator when it is just refueled and under high temperatures. Dodge Avenger Fuel Level Sensor is typically located within the fuel tank and is made up of a float, an actuating rod and a resistor to enable it transmit signals to the fuel gauge. Some variation in design may occur from one model year to the next, but fundamentally, the basic operation of the system remains the same and is oriented toward the reliability of the method of determining fuel quantities. It is important for a vehicle to have a properly functioning Fuel Level Sensor in order to provide the vehicle with the performance that it requires, and therefore if there is a problem with Fuel Level Sensor, then it needs to be repaired soon.

Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Dodge Avenger Fuel Level Sensor at great affordable prices. Moreover, all genuine Dodge Avenger Fuel Level Sensor come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.

Dodge Avenger Fuel Level Sensor Parts Questions & Experts Answers

Level Unit Module Kit
68042937AA
Q: How to Remove and Install a Fuel Pump/Fuel Pressure Regulator/Fuel Level Sending Unit Assembly on a Dodge Avenger?
A: All wheel drive (AWD) models have a saddle fuel tank configuration and have main and auxiliary fuel pumps. Each fuel pump has a sending unit. The auxiliary fuel pump contains the fuel pump reservoir, fuel pressure regulator and fuel filter. Relieve the fuel system pressure. Disconnect the negative battery cable from the remote ground terminal or battery. Remove the rear seat cushion and fuel pump module cover. On AWD models, remove main and auxiliary fuel pump module covers. Disconnect the fuel delivery line quick-connect fitting and on 2015 and later models, also disconnect the fuel vapor line from the fuel pump/fuel pressure regulator/Fuel Level Sensor assembly. Disconnect the electrical connector from the fuel pump/fuel pressure regulator/Fuel Level Sensor assembly. Before removing the fuel pump/fuel pressure regulator/Fuel Level Sensor assembly, make alignment marks on the assembly and the fuel tank (if marks don't already exist), to ensure the assembly will be correctly realigned when it's installed again. Using adjustable-joint pliers, loosen the lock ring that secures the fuel pump/fuel pressure regulator/Fuel Level Sensor assembly. Carefully lift the fuel pump/fuel pressure regulator/Fuel Level Sensor assembly from the fuel tank. Angle the module so that you don't bend the float arm of the Fuel Level Sensor or damage the fuel pump inlet strainer. If you're removing the auxiliary pump on an AWD model, raise the fuel pump module and disconnect the internal fuel line. While the pump is removed, inspect the pump inlet strainer. Make sure that it's not clogged or damaged. If the inlet strainer is dirty, try washing it in clean solvent. If it's still clogged, replace it. Installation is the reverse of removal. Line up the marks, and tighten the fuel pump module lock ring securely.