How to Remove and Install the CMP Sensor on Dodge Caravan?

Disconnect the cable from the negative terminal of the battery. Disconnect the CMP sensor electrical connector. Remove the CMP sensor retaining bolts and remove the CMP sensor. Remove the screw that attaches the target magnet to the camshaft and then remove the target magnet. When installing the target magnet, make sure that the locating dowels on the back of the magnet are aligned with the locating holes in the end of the camshaft. Tighten the target magnet retaining screw to the specified torque. Installation is otherwise the reverse of removal. Be sure to tighten the CMP sensor retaining bolts to the specified torque. For 3.3L/3.8L V6 models, disconnect the cable from the negative terminal of the battery. Remove the air intake duct and the air filter housing. Disconnect the CMP sensor electrical connector. Remove the CMP sensor mounting bolt. Rotate the CMP sensor away from the block, then pull it up and out of the timing chain cover. If reinstalling the same sensor, remove the paper spacer from the end of the sensor. Remove the old O-ring from the CMP sensor. If installing the old CMP sensor, clean off the sensor face and install a new paper spacer on the face before installing the sensor. Inspect the old O-ring for damage and replace if necessary. Apply a few drops of clean engine oil to the O-ring, then carefully install the CMP sensor in the timing chain cover and rotate it into position. Installation is otherwise the reverse of removal. Be sure to tighten the CMP sensor mounting bolt to the specified torque.

Genuine Dodge Caravan Camshaft Position Sensor

Cam Position Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

4 Camshaft Position Sensors found

View related parts
Dodge Caravan Sensor-CAMSHAFT
Part Number: 4686353
$78.18 MSRP: $120.00
You Save: $41.82 (35%)
ADD TO CART
Product Specifications
- Other Name: Sensor D.I.S. Camshaft Reference; Camshaft Position Sensor, Camshaft Sensor
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1998-2007 Dodge Caravan | Base, C/V, LE, SE, Sport, SXT | 6 Cyl 3.3L, 6 Cyl 3.8L
View related parts
Dodge Caravan SENSORPKG-CAMSHAFT
Part Number: 4882851AB
$82.92 MSRP: $126.00
You Save: $43.08 (35%)
ADD TO CART
Product Specifications
- Other Name: Sensor Package Camshaft
- Replaced by: 5093508AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1999-2002 Dodge Caravan | Base, EC, LE, SE | 4 Cyl 2.4L
View related parts
Dodge Caravan SENSORPKG-CAMSHAFT
Part Number: 5093508AA
$89.41 MSRP: $126.00
You Save: $36.59 (30%)
ADD TO CART
Product Specifications
- Other Name: Sensor Package Camshaft; Camshaft Position Sensor, Camshaft Sensor
- Replaces: 4882851AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1999-2007 Dodge Caravan | Base, C/V, EC, LE, SE | 4 Cyl 2.4L
View related parts
Dodge Caravan Sensor-D.I.S. CAMSHAFT Reference
Part Number: 4727138AB
$0.00
Product Specifications
- Other Name: Sensor D.I.S. Camshaft Reference; Camshaft Position Sensor, Camshaft Sensor
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1997 Dodge Caravan | Base, LE, SE | 6 Cyl 3.3L, 6 Cyl 3.8L

Dodge Caravan Camshaft Position Sensor

Camshaft Position Sensor in the Dodge Caravan automobiles is among the most important components of the engine that gauges the position and the speed of the camshaft. This information is then sent to the engine control module or the ECM which controls the flow of fuel and the timing of ignition in order to produce the most effective kind of combustion in the engine. Usually, the Dodge Caravan Camshaft Position Sensor is located right above the camshaft, although its position might differ depending on a certain model. Thus, different types of Camshaft Position Sensors Years have been incorporated in Dodge Caravan cars, including the differences in mounting location and construction. Regardless of the type, the primary function remains the same: to coordinate the activities of the engine especially in relation with crank sensor that plays an important role in controlling fuel injection timing and engine speed. Neglected Camshaft Position Sensor may posses severe performance problems that prove its relevance to the general functioning of the Dodge Caravan.

Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Dodge Caravan Camshaft Position Sensor at great affordable prices. Moreover, all genuine Dodge Caravan Camshaft Position Sensor come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.

Dodge Caravan Camshaft Position Sensor Parts Questions & Experts Answers

Sensor-CAMSHAFT
4686353
Q: How to Remove and Install the CMP Sensor on Dodge Caravan?
A: Disconnect the cable from the negative terminal of the battery. Disconnect the CMP sensor electrical connector. Remove the CMP sensor retaining bolts and remove the CMP sensor. Remove the screw that attaches the target magnet to the camshaft and then remove the target magnet. When installing the target magnet, make sure that the locating dowels on the back of the magnet are aligned with the locating holes in the end of the camshaft. Tighten the target magnet retaining screw to the specified torque. Installation is otherwise the reverse of removal. Be sure to tighten the CMP sensor retaining bolts to the specified torque. For 3.3L/3.8L V6 models, disconnect the cable from the negative terminal of the battery. Remove the air intake duct and the air filter housing. Disconnect the CMP sensor electrical connector. Remove the CMP sensor mounting bolt. Rotate the CMP sensor away from the block, then pull it up and out of the timing chain cover. If reinstalling the same sensor, remove the paper spacer from the end of the sensor. Remove the old O-ring from the CMP sensor. If installing the old CMP sensor, clean off the sensor face and install a new paper spacer on the face before installing the sensor. Inspect the old O-ring for damage and replace if necessary. Apply a few drops of clean engine oil to the O-ring, then carefully install the CMP sensor in the timing chain cover and rotate it into position. Installation is otherwise the reverse of removal. Be sure to tighten the CMP sensor mounting bolt to the specified torque.