How to Determine Which ABS System Is on My Dodge Charger and How to Remove and Install a Power Brake Booster?

Vehicle models equipped with an Anti-lock brake system (ABS) will have one of two different factory systems installed, one is MK25 (the earlier ABS system) and can be Identified by a pressure sensor mounted to the bottom of the master cylinder. The other is MK25E (the later ABS system) and the master cylinder appears typical and is not equipped with a pressure sensor on the bottom. Use this Information to determine which system is on your vehicle. Knowing which system you have is important regarding part identification and torque specifications. The operating check involves depressing the brake pedal several times with the engine off and making sure there's no change in the pedal reserve distance. Then, depress the pedal and start the engine to check if the pedal goes down slightly, indicating normal operation. The airtightness check includes starting the engine and turning it off after one or two minutes, then depressing the brake pedal slowly several times to check if the pedal depresses less each time, indicating an airtight booster. Another airtightness check involves depressing the brake pedal while the engine is running and stopping the engine with the pedal depressed, checking if there's no change in the pedal reserve travel after holding the pedal for 30 seconds. The power brake booster is not serviceable and should be replaced with a new or rebuilt unit. Models equipped with ESP may have additional components integrated with the power brake booster, requiring all original components to be present in the new or rebuilt unit. To remove the power brake booster, start by pressing the brake pedal several times to remove any stored vacuum in the booster. Then, move the driver's seat to the rearmost position and disconnect the cable(s) from the negative battery terminal(s). Remove the windshield wiper motor and the brake master cylinder. Remove any electrical connectors attached to the power brake booster, if applicable. Carefully disconnect the vacuum hose from the brake booster check valve. Inside the vehicle, remove the brake light switch. Pry the retaining clip off of the brake pedal pin and disconnect the booster push rod. Remove the booster mounting fasteners and slide the booster straight out from the firewall until the studs clear the holes. Installation procedures are basically the reverse of removal, including replacing the seal between the power booster and the firewall, tightening the booster mounting nuts, installing a new retaining clip securing the booster pushrod to the brake pedal pin, bleeding the brake system, and testing the operation of the brakes before putting the vehicle into normal service.

Genuine Dodge Charger Brake Booster

Brake Power Booster

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

12 Brake Boosters found

View related parts
Dodge Charger Booster-Power Brake
Part Number: 68048544AA
$307.50 MSRP: $414.00
You Save: $106.50 (26%)
ADD TO CART
Product Specifications
- Other Name: Booster Power Brake; Booster, Brake Booster
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009-2010 Dodge Charger | Base AWD, Base RWD, R/T AWD, R/T RWD, Rallye AWD, Rallye RWD, SRT8 RWD, SXT AWD, SXT RWD | 6 Cyl 2.7L, 6 Cyl 3.5L, 8 Cyl 5.7L, 8 Cyl 6.1L
View related parts
Dodge Charger Booster-Power Brake
Part Number: 68089130AA
$217.56 MSRP: $329.00
You Save: $111.44 (34%)
ADD TO CART
Product Specifications
- Other Name: Booster Power Brake
- Replaced by: 68089130AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2012 Dodge Charger | Police RWD, R/T AWD, R/T RWD, SE RWD, SRT8 RWD, SRT8 Superbee RWD, SXT AWD, SXT RWD, V6 AWD | 6 Cyl 3.6L, 8 Cyl 5.7L, 8 Cyl 6.4L
View related parts
Dodge Charger Power Brake
Part Number: 68089130AD
$219.55 MSRP: $329.00
You Save: $109.45 (34%)
ADD TO CART
Product Specifications
- Other Name: Booster, Brake Booster
- Replaces: 68089130AC, 68089130AB, 68089130AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2023 Dodge Charger | GT AWD, GT RWD, Police AWD, Police RWD, R/T 392 RWD, R/T AWD, R/T RWD, SE AWD, SE RWD, SRT 392 RWD, SRT Hellcat RWD, SRT Hellcat Widebody RWD, SRT RWD, SRT Superbee RWD, SRT8 RWD, SRT8 Superbee RWD, SXT AWD, SXT Plus RWD, SXT RWD, Scat Pack RWD, V6 AWD | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.6L, 8 Cyl 5.7 L GAS, 8 Cyl 5.7L, 8 Cyl 6.2 L GAS, 8 Cyl 6.2L, 8 Cyl 6.4 L GAS, 8 Cyl 6.4L
View related parts
Dodge Charger Power Brake
Part Number: 68089130AC
$236.47 MSRP: $329.00
You Save: $92.53 (29%)
ADD TO CART
Product Specifications
- Replaced by: 68089130AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2020 Dodge Charger | GT AWD, GT RWD, Police AWD, Police RWD, R/T RWD, Scat Pack RWD, SRT Hellcat Widebody RWD, SXT AWD, SXT RWD | 6 Cyl 3.6L, 8 Cyl 5.7L, 8 Cyl 6.2L, 8 Cyl 6.4L
View related parts
Dodge Charger Booster-Power Brake
Part Number: 68089130AB
$217.56 MSRP: $329.00
You Save: $111.44 (34%)
ADD TO CART
Product Specifications
- Other Name: Booster Power Brake
- Replaced by: 68089130AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2013-2019 Dodge Charger | GT AWD, GT RWD, Police AWD, Police RWD, R/T 392 RWD, R/T AWD, R/T RWD, Scat Pack RWD, SE AWD, SE RWD, SRT 392 RWD, SRT Hellcat RWD, SRT RWD, SRT Superbee RWD, SRT8 RWD, SRT8 Superbee RWD, SXT AWD, SXT Plus RWD, SXT RWD, V6 AWD | 6 Cyl 3.6L, 8 Cyl 5.7L, 8 Cyl 6.2L, 8 Cyl 6.4L
View related parts
Dodge Charger Booster-Power Brake
Part Number: 68237808AA
$280.50 MSRP: $430.00
You Save: $149.50 (35%)
ADD TO CART
Product Specifications
- Other Name: Booster Power Brake; Brake Booster
- Replaced by: 68237808AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2014-2019 Dodge Charger | GT AWD, GT RWD, Police AWD, Police RWD, R/T 392 RWD, R/T AWD, R/T RWD, Scat Pack RWD, SE AWD, SE RWD, SRT 392 RWD, SRT Hellcat RWD, SRT RWD, SRT Superbee RWD, SXT AWD, SXT Plus RWD, SXT RWD | 6 Cyl 3.6L, 8 Cyl 5.7L, 8 Cyl 6.2L, 8 Cyl 6.4L
View related parts
Dodge Charger Power Brake
Part Number: 68237808AB
$280.50 MSRP: $430.00
You Save: $149.50 (35%)
ADD TO CART
Product Specifications
- Other Name: Brake Booster
- Replaced by: 68237808AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2020 Dodge Charger | GT AWD, GT RWD, Police AWD, Police RWD, R/T RWD, Scat Pack RWD, SRT Hellcat Widebody RWD, SXT AWD, SXT RWD | 6 Cyl 3.6L, 8 Cyl 5.7L, 8 Cyl 6.2L, 8 Cyl 6.4L
View related parts
Dodge Charger Power Brake
Part Number: 68237808AC
$280.50 MSRP: $430.00
You Save: $149.50 (35%)
ADD TO CART
Product Specifications
- Other Name: Booster, Brake Booster
- Replaces: 68237808AA, 68237808AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2014-2023 Dodge Charger | GT AWD, GT RWD, Police AWD, Police RWD, R/T 392 RWD, R/T AWD, R/T RWD, SE AWD, SE RWD, SRT 392 RWD, SRT Hellcat RWD, SRT Hellcat Widebody RWD, SRT RWD, SRT Superbee RWD, SXT AWD, SXT Plus RWD, SXT RWD, Scat Pack RWD | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.6L, 8 Cyl 5.7 L GAS, 8 Cyl 5.7L, 8 Cyl 6.2 L GAS, 8 Cyl 6.2L, 8 Cyl 6.4 L GAS, 8 Cyl 6.4L
View related parts
Dodge Charger Booster-Power Brake
Part Number: 5189172AA
Product Specifications
- Other Name: Booster Power Brake
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2006-2007 Dodge Charger | Base AWD, Base RWD, R/T AWD, R/T RWD, SRT8 RWD | 6 Cyl 2.7L, 6 Cyl 3.5L, 8 Cyl 5.7L, 8 Cyl 6.1L
View related parts
Dodge Charger Booster-Power Brake
Part Number: 68033785AA
Product Specifications
- Other Name: Booster Power Brake; Booster, Brake Booster
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008 Dodge Charger | Base AWD, Base RWD, R/T AWD, R/T RWD, SRT8 RWD, SXT AWD, SXT RWD | 6 Cyl 2.7L, 6 Cyl 3.5L, 8 Cyl 5.7L, 8 Cyl 6.1L
View related parts
Dodge Charger Booster-Power Brake
Part Number: 5139145AA
Product Specifications
- Other Name: Booster Power Brake; Booster, Brake Booster
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2006 Dodge Charger | Base RWD, R/T RWD | 6 Cyl 2.7L, 6 Cyl 3.5L, 8 Cyl 5.7L
View related parts
Dodge Charger Booster-Power Brake
Part Number: 5139152AA
Product Specifications
- Other Name: Booster Power Brake; Booster, Brake Booster
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2006 Dodge Charger | Base RWD, R/T RWD | 6 Cyl 2.7L, 6 Cyl 3.5L, 8 Cyl 5.7L

Dodge Charger Brake Booster

This component known as the Brake Booster is very important especially in Dodge Charger since it helps in boosting the brakes to reduce the amount of pressure you need to apply in order to get the brakes working. This component works via a vacuum chamber that multiplies the hydraulic pressure developed by the master cylinder thus enhancing on the force applied by the driver on the brake pedal. Intake manifold gaskets on Dodge Charger models use a vacuum servo also referred to as a brake booster since it helps to minimize the force the driver has to apply when stopping their vehicle. Thus let it be mentioned that the brake booster operates only when the engine is running, and in the case of an engine shut down its usage is limited to few attempts of brake usage only.

Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Dodge Charger Brake Booster at great affordable prices. Moreover, all genuine Dodge Charger Brake Booster come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.

Dodge Charger Brake Booster Parts Questions & Experts Answers

Booster-Power Brake
68048544AA
Q: How to Determine Which ABS System Is on My Dodge Charger and How to Remove and Install a Power Brake Booster?
A: Vehicle models equipped with an Anti-lock brake system (ABS) will have one of two different factory systems installed, one is MK25 (the earlier ABS system) and can be Identified by a pressure sensor mounted to the bottom of the master cylinder. The other is MK25E (the later ABS system) and the master cylinder appears typical and is not equipped with a pressure sensor on the bottom. Use this Information to determine which system is on your vehicle. Knowing which system you have is important regarding part identification and torque specifications. The operating check involves depressing the brake pedal several times with the engine off and making sure there's no change in the pedal reserve distance. Then, depress the pedal and start the engine to check if the pedal goes down slightly, indicating normal operation. The airtightness check includes starting the engine and turning it off after one or two minutes, then depressing the brake pedal slowly several times to check if the pedal depresses less each time, indicating an airtight booster. Another airtightness check involves depressing the brake pedal while the engine is running and stopping the engine with the pedal depressed, checking if there's no change in the pedal reserve travel after holding the pedal for 30 seconds. The power brake booster is not serviceable and should be replaced with a new or rebuilt unit. Models equipped with ESP may have additional components integrated with the power brake booster, requiring all original components to be present in the new or rebuilt unit. To remove the power brake booster, start by pressing the brake pedal several times to remove any stored vacuum in the booster. Then, move the driver's seat to the rearmost position and disconnect the cable(s) from the negative battery terminal(s). Remove the windshield wiper motor and the Brake Master Cylinder. Remove any electrical connectors attached to the power brake booster, if applicable. Carefully disconnect the vacuum hose from the brake booster check valve. Inside the vehicle, remove the Brake Light Switch. Pry the retaining clip off of the brake pedal pin and disconnect the booster push rod. Remove the booster mounting fasteners and slide the booster straight out from the firewall until the studs clear the holes. Installation procedures are basically the reverse of removal, including replacing the seal between the power booster and the firewall, tightening the booster mounting nuts, installing a new retaining clip securing the booster pushrod to the brake pedal pin, bleeding the brake system, and testing the operation of the brakes before putting the vehicle into normal service.

Related Dodge Charger Parts

Browse by Year

2023 Brake Booster 2022 Brake Booster 2021 Brake Booster 2020 Brake Booster 2019 Brake Booster 2018 Brake Booster 2017 Brake Booster 2016 Brake Booster 2015 Brake Booster 2014 Brake Booster 2013 Brake Booster 2012 Brake Booster 2011 Brake Booster 2010 Brake Booster 2009 Brake Booster 2008 Brake Booster 2007 Brake Booster 2006 Brake Booster