How do you replace the ignition switch and lock cylinder on Dodge Neon?

There are few steps needed to perform to replace the ignition switch, the first step is to remove the battery negative cable and then isolate it from the terminal. Pull off the steering column covers and the ignition lock cylinder. Release the electrical connection with the switch of the ignition and remove the Torx head screw fixed on the steering column for the switch. Press the retaining tabs inwards to release the switch and lower it out of the column, if necessary using a screwdriver. When fitting the new switch, physically position the switch to the ON state and align the actuator shaft to be also in the ON position before engaging. The installation process is done in the reverse order in which the removal process was done. However for the lock cylinder it is recommended that you disconnect and isolate the negative cable. Place the ignition key and turn the switch on. Insert a small screwdriver and push on the retainer tab through the hole provided at the lower part of the steering column cover. Remove the ignition lock cylinder from the housing. Align the slot in the ignition switch to the ON position and then place the new ignition lock cylinder till the positioning tab comes under the housing and test the key operation.

Genuine Dodge Neon Ignition Lock Cylinder

Ignition Key Lock Cylinder

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

5 Ignition Lock Cylinders found

View related parts
Dodge Neon Cylinder Lock-Ignition Lock
Part Number: 5003843AB
$116.21 MSRP: $205.00
You Save: $88.79 (44%)
ADD TO CART
Product Specifications
- Other Name: Cylinder Ignition Lock
- Replaced by: 5083915AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2003 Dodge Neon | 4 Door High Line, ACR, Base, ES, R/T, S, SE, SRT-4, SXT | 4 Cyl 1.6L, 4 Cyl 2.0L, 4 Cyl 2.4L
View related parts
Dodge Neon Cylinder Lock-Ignition Lock
Part Number: 5083915AB
$116.21 MSRP: $205.00
You Save: $88.79 (44%)
ADD TO CART
Product Specifications
- Other Name: Cylinder Ignition Lock
- Replaces: 5003843AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2004 Dodge Neon | 4 Door High Line, ACR, Base, ES, R/T, S, SE, SRT-4, SXT | 4 Cyl 1.6L, 4 Cyl 2.0L, 4 Cyl 2.4L
View related parts
Dodge Neon Cylinder-Ignition Lock
Part Number: 5139207AA
$134.23 MSRP: $200.00
You Save: $65.77 (33%)
ADD TO CART
Product Specifications
- Other Name: Cylinder Ignition Lock
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2004-2005 Dodge Neon | ACR, R/T, SE, SRT-4, SXT | 4 Cyl 2.0L, 4 Cyl 2.4L
View related parts
Dodge Neon CYLINDER/LOCK-Ignition Module
Part Number: 4746667
$50.59 MSRP: $73.05
You Save: $22.46 (31%)
ADD TO CART
Product Specifications
- Other Name: Cylinder Lock Package Ignition Black Plastic; Ignition Lock Cylinder, Lock Cylinder
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1995-1997 Dodge Neon | 2 Door Base, 2 Door High Line, 2 Door High Line , 2 Door Sport, 4 Door Base, 4 Door High Line, 4 Door Sport | 4 Cyl 2.0L
View related parts
Dodge Neon Cylinder Lock-Ignition Lock
Part Number: 4746666
$26.99 MSRP: $34.87
You Save: $7.88 (23%)
ADD TO CART
Product Specifications
- Other Name: Cylinder, Ignition
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1997 Dodge Neon | 2 Door Base, 2 Door High Line , 2 Door Sport, 4 Door Base, 4 Door High Line, 4 Door Sport | 4 Cyl 2.0L

Dodge Neon Ignition Lock Cylinder

The Ignition Lock Cylinder for the Dodge Neon cars primarily provide the function of starting the engine by a key that is inserted and rotated. This goes as a component of the ignition switch, it directs electrical power to the required circuits when the right key is inserted. Earlier models Dodge neon ignition lock cylinder used the key operated systems while the later models have other special features like coded keys that deals with your computers within the automobile. However, over time, the Dodge neon ignition lock cylinder show signs of wear and malfunction making it challenging to turn the key or starting of the engine. Problems may develop due to the condition of keys or tumblers or imperfection of the ignition switch. In total, the Ignition Lock Cylinder continues to hold a central position in the structure and functionality of Dodge Neon vehicles so that only an authorized individual can start the vehicle engine.

Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Dodge Neon Ignition Lock Cylinder at great affordable prices. Moreover, all genuine Dodge Neon Ignition Lock Cylinder come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.

Dodge Neon Ignition Lock Cylinder Parts Questions & Experts Answers

Cylinder Lock-Ignition Lock
5003843AB
Q: How do you replace the ignition switch and lock cylinder on Dodge Neon?
A: There are few steps needed to perform to replace the ignition switch, the first step is to remove the battery negative cable and then isolate it from the terminal. Pull off the steering column covers and the ignition lock cylinder. Release the electrical connection with the switch of the ignition and remove the Torx head screw fixed on the steering column for the switch. Press the retaining tabs inwards to release the switch and lower it out of the column, if necessary using a screwdriver. When fitting the new switch, physically position the switch to the ON state and align the actuator shaft to be also in the ON position before engaging. The installation process is done in the reverse order in which the removal process was done. However for the lock cylinder it is recommended that you disconnect and isolate the negative cable. Place the ignition key and turn the switch on. Insert a small screwdriver and push on the retainer tab through the hole provided at the lower part of the steering column cover. Remove the ignition lock cylinder from the housing. Align the slot in the ignition switch to the ON position and then place the new ignition lock cylinder till the positioning tab comes under the housing and test the key operation.