How do you disconnect the negative battery cable and replace the Throttle Position (TP) sensor on Dodge Neon?

Remove the negative terminal of the battery. Throttle Position (TP) sensor is situated on the front part of the throttle body which is fixed on the air filter housing; if the throttle body is disconnected from the air filter housing and from the air intake duct, it will be comparatively easy to replace the TP sensor as it is enough to disconnect the electrical connector and to remove the sensor retaining screws. It is necessary to unscrew the electrical connector and, then, take out two screws of the TP sensor mounting before taking out the TP sensor. It is necessary to remove and take out the old TP sensor O-ring and replace it with a new one before placing the TP sensor. During installation, the blade at the end of throttle shaft has to be slotted into the whole on the backside of the TP sensor in such a way that the two intended tabs on the interior of the hole will make contact with two sides of the blade. Put the two mounting holes of the TP sensor just a few degree leftward to the holes of the throttle body, then turn clockwise until it is correctly fixed; it will meet some resistance when turned to the right position. For steering, if it is hard to turn check that the throttle shaft blade sits properly on the tabs.

Genuine Dodge Neon Throttle Position Sensor

TPS Switch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

5 Throttle Position Sensors found

View related parts
Dodge Neon Throttle Position Sensor Kit
Part Number: 4874430AB
$97.33 MSRP: $125.00
You Save: $27.67 (23%)
ADD TO CART
Product Specifications
- Other Name: SENSR Kit-Throttle Position; Throttle Position Sensor, Throttle Sensor
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1999-2005 Dodge Neon | 2 Door Base, 2 Door High Line , 4 Door Base, 4 Door High Line, ACR, Base, ES, R/T, S, SE, SXT | 4 Cyl 2.0L
View related parts
Dodge Neon Throttle Position Sensor
Part Number: 4606196
Product Specifications
- Other Name: Sensor-Throttle Position
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2003-2005 Dodge Neon | SRT-4 | 4 Cyl 2.4L
View related parts
Dodge Neon Throttle Position Sensor Kit
Part Number: 4874433
Product Specifications
- Other Name: SENSR Kit-Throttle Position; Throttle Position Sensor
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1997-1999 Dodge Neon | 2 Door Base, 2 Door High Line , 2 Door Sport, 4 Door High Line, 4 Door Sport | 4 Cyl 2.0L
View related parts
Dodge Neon Throttle Inlet Pressure Sensor
Part Number: 5029347AA
Product Specifications
- Other Name: Sensor And Bracket Throttle Inlet Pressure
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2003-2005 Dodge Neon | SRT-4 | 4 Cyl 2.4L
View related parts
Dodge Neon Throttle Inlet Pressure Sensor
Part Number: 5033223AA
Product Specifications
- Other Name: Sensor And Bracket Throttle Inlet Pressure
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2003 Dodge Neon | SRT-4 | 4 Cyl 2.4L

Dodge Neon Throttle Position Sensor

Dodge Neon automobiles are fitted with a Throttle Position Sensor (TPS) which is very vital in the controls of the air-fuel mixture to enhance combustion. The TPS track the throttle position in real time and transmits this information to the fuel injection system in relation to power demands therefore the engine control unit changes fuel delivery. It repeated several times per second thus allowing for good acceleration and deceleration. Many of Dodge Neon automobiles have installed potentiometric TPS of analog or have modern non-contact ones based on Hall effect or magnetoresistive effect. The latter on the other hand provides an improved reliability through the said benefit since there is no physical contact that causes the wear resulting to improved performance. Furthermore, more sophisticated sensors such as the closed throttle position sensor (CTPS) is used to give feedback especially in electronically controlled systems of throttle control in an engine in an effort to enhance efficiency. The throttle position sensor failure may result in low fuel efficiency together with performance problems, and should be replaced.

Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Dodge Neon Throttle Position Sensor at great affordable prices. Moreover, all genuine Dodge Neon Throttle Position Sensor come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.

Dodge Neon Throttle Position Sensor Parts Questions & Experts Answers

Throttle Inlet Pressure Sensor
5029347AA
Q: How do you disconnect the negative battery cable and replace the Throttle Position (TP) sensor on Dodge Neon?
A: Remove the negative terminal of the battery. Throttle Position (TP) sensor is situated on the front part of the throttle body which is fixed on the air filter housing; if the throttle body is disconnected from the air filter housing and from the air intake duct, it will be comparatively easy to replace the TP sensor as it is enough to disconnect the electrical connector and to remove the sensor retaining screws. It is necessary to unscrew the electrical connector and, then, take out two screws of the TP sensor mounting before taking out the TP sensor. It is necessary to remove and take out the old TP sensor O-ring and replace it with a new one before placing the TP sensor. During installation, the blade at the end of throttle shaft has to be slotted into the whole on the backside of the TP sensor in such a way that the two intended tabs on the interior of the hole will make contact with two sides of the blade. Put the two mounting holes of the TP sensor just a few degree leftward to the holes of the throttle body, then turn clockwise until it is correctly fixed; it will meet some resistance when turned to the right position. For steering, if it is hard to turn check that the throttle shaft blade sits properly on the tabs.