How do you adjust the intake and exhaust valves on an engine after removing the rocker arm cover on Dodge Ramcharger?

Tag and remove the PCV and vacuum hoses from the rocker arm cover, then remove the rocker arm cover. Start the engine and warm it up to normal operating temperature. With the engine thoroughly warmed up and idling, adjust the intake and exhaust valves, noting that the clearances for the intake and exhaust valves are different; exercise caution around moving and hot engine parts. Insert an appropriate size feeler gauge between the valve stem and the rocker arm adjusting screw; if the feeler gauge fits with a slight drag, the clearance is correct and no adjustment is needed. If the feeler gauge does not fit or is loose, carefully tighten or loosen the adjusting screw until a slight drag is felt when withdrawing the feeler gauge. Counting from the front of the engine, the exhaust valves are Nos. 1-3-5-8-10 and 12, while the intake valves are Nos. 2-4-6-7-9 and 11. The rocker arm adjusting screws are an interference thread type and do not require a locknut; always use a close-fitting box wrench to turn them. Install the rocker arm cover with a new gasket and tighten the mounting nuts evenly and securely, then reinstall the PCV and vacuum hoses. Finally, start the engine and check for oil leakage between the rocker arm cover and the cylinder head.

Genuine Dodge Ramcharger Intake Valve

Engine Intake Valve

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 Intake Valves found

View related parts
Dodge Ramcharger Valve-Intake
Part Number: 53006723
$19.26 MSRP: $24.50
You Save: $5.24 (22%)
ADD TO CART
Product Specifications
- Other Name: Valve Intake Standard; Intake Valve
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1992-1993 Dodge Ramcharger | Sport Utility 2WD, Sport Utility 4WD | 8 Cyl 5.2L, 8 Cyl 5.9L
View related parts
Dodge Ramcharger Valve Intake
Part Number: 4713216
Product Specifications
- Other Name: Valve, Intake; Intake Valve
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1990-1993 Dodge Ramcharger | Sport Utility 2WD, Sport Utility 4WD | 6 Cyl 5.9L Diesel
View related parts
Dodge Ramcharger Valve-Intake
Part Number: 53009285
Product Specifications
- Other Name: Valve Intake .015" O/S
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1992-1993 Dodge Ramcharger | Sport Utility 2WD, Sport Utility 4WD | 8 Cyl 5.2L, 8 Cyl 5.9L
View related parts
Dodge Ramcharger Valve-Intake
Part Number: 53009287
Product Specifications
- Other Name: Valve Intake .003" O/S
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1992-1993 Dodge Ramcharger | Sport Utility 2WD, Sport Utility 4WD | 8 Cyl 5.2L, 8 Cyl 5.9L
View related parts
Dodge Ramcharger Valve-Intake
Part Number: 53020319
Product Specifications
- Other Name: Valve, Intake
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1990-1993 Dodge Ramcharger | Sport Utility 2WD, Sport Utility 4WD | 8 Cyl 5.2L
View related parts
Dodge Ramcharger Valve-Intake
Part Number: 1947623
Product Specifications
- Other Name: Valve, Intake Standard; Intake Valve
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1984-1987 Dodge Ramcharger | 6 Cyl 3.7L

Dodge Ramcharger Intake Valve

Intake Valve is one of the most vital parts that directly contribute to the improvement of the performances of the Dodge Ramcharger vehicles and also the effectiveness of combustion. Its main task is controlling when air and fuel mixture should entered into the engine and that is crucial for maximum power production. The Intake Valve is such an important item because when it fails, the engine will have inefficient combustion, and the car's power output will be compromised, which means that when it fails, it will need to be replaced as soon as possible to prevent having to spend a lot of money on repairs. Through the years of production of Dodge Ramcharger models, there have been many styles of Intake Valves used, all serving certain performance requirements. The steps of Replacing a damaged Intake Valve includes are removal steps like Use of special tool such as a valve spring remover and compressor. Proper installation is crucial in order to sustain the structural efficiency of the valve system so that do Dodge ramcharger could continue to perform its function.

Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Dodge Ramcharger Intake Valve at great affordable prices. Moreover, all genuine Dodge Ramcharger Intake Valve come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.

Dodge Ramcharger Intake Valve Parts Questions & Experts Answers

Valve-Intake
53006723
Q: How do you adjust the intake and exhaust valves on an engine after removing the rocker arm cover on Dodge Ramcharger?
A: Tag and remove the PCV and vacuum hoses from the rocker arm cover, then remove the rocker arm cover. Start the engine and warm it up to normal operating temperature. With the engine thoroughly warmed up and idling, adjust the intake and exhaust valves, noting that the clearances for the intake and exhaust valves are different; exercise caution around moving and hot engine parts. Insert an appropriate size feeler gauge between the valve stem and the rocker arm adjusting screw; if the feeler gauge fits with a slight drag, the clearance is correct and no adjustment is needed. If the feeler gauge does not fit or is loose, carefully tighten or loosen the adjusting screw until a slight drag is felt when withdrawing the feeler gauge. Counting from the front of the engine, the exhaust valves are Nos. 1-3-5-8-10 and 12, while the intake valves are Nos. 2-4-6-7-9 and 11. The rocker arm adjusting screws are an interference thread type and do not require a locknut; always use a close-fitting box wrench to turn them. Install the rocker arm cover with a new gasket and tighten the mounting nuts evenly and securely, then reinstall the PCV and vacuum hoses. Finally, start the engine and check for oil leakage between the rocker arm cover and the cylinder head.