Chrysler 5085074AE Bracket-Engine Mount

You can Select Your Vehicle to check if 5085074AE fits your vehicle.

To replace the right mount, raise the vehicle, remove the power steering fluid reservoir, support the engine, and take out the engine mount bracket and the mount itself. Replace it with a new one and tighten the bolts.

To replace the right mount, remove the coolant reservoir, raise the vehicle, and remove the under-vehicle splash shield. Move the heater tube out of the way, then remove the engine mount bracket-to-timing cover support bolts and the engine mount bracket-to-mount bolts. Support the engine, remove the engine mount-to-body bolts, and the body-to-mount bolts from underneath. Replace the engine mount, tighten the body-to-mount bolts, lower the engine, and tighten the mount-to-bracket bolts. The installation follows the reverse order.

The right mount requires removing the lower splash shield, engine ground strap, and specific fasteners before installing a new mount.

Engine mounts seldom require attention, but broken or deteriorated mounts should be replaced immediately to prevent damage or accelerated wear on driveline components.

To check the mounts, the engine must be raised slightly to remove the weight from them. This involves securely supporting the vehicle on jackstands, positioning a jack under the engine oil pan with a wood block to prevent damage, and carefully raising the engine.

To check the mounts, the engine must be raised slightly to relieve weight from them. Begin by raising the vehicle and securely supporting it on jackstands. Then, remove the front wheels and tires. Position two jacks-one under the crankshaft pulley and the other under the transaxle bellhousing-using a block of wood to protect the components while raising the engine/transaxle just enough to relieve the mounts. Inspect the mounts for any cracks, hardened rubber, or separation from the metal plates, and check for movement between the mount plates and the engine or subframe. Tighten any loose fasteners as necessary. Applying rubber preservative can help slow deterioration.

There are four powertrain mounts: 1. The front mount connects the transaxle to the crossmember. 2. The left mount secures the driver's side of the engine to the subframe. 3. The right engine mount attaches the engine block to the passenger's side of the subframe. 4. The rear mount links the engine block to the subframe.

For the left mount, disconnect the negative battery cable, raise the vehicle, remove the middle engine splash shield and air filter housing, support the transaxle, and then remove the mounting bolts to replace the mount. Ensure to tighten the bolts to the specified torque.

To check the mounts, the engine must be raised slightly to relieve weight from them. Begin by raising the vehicle and securely supporting it on jackstands. Then, remove the front wheels and tires. Position two jacks-one under the crankshaft pulley and the other under the transaxle bellhousing-using a block of wood to protect the components while raising the engine/transaxle just enough to relieve the mounts. Inspect the mounts for any cracks, hardened rubber, or separation from the metal plates, and check for movement between the mount plates and the engine or subframe. Tighten any loose fasteners as necessary. Applying rubber preservative can help slow deterioration.

To check the mounts, the engine must be raised slightly to relieve weight from them. Begin by raising the vehicle and securely supporting it on jackstands. Then, remove the front wheels and tires. Position two jacks-one under the crankshaft pulley and the other under the transaxle bellhousing-using a block of wood to protect the components while raising the engine/transaxle just enough to relieve the mounts. Inspect the mounts for any cracks, hardened rubber, or separation from the metal plates, and check for movement between the mount plates and the engine or subframe. Tighten any loose fasteners as necessary. Applying rubber preservative can help slow deterioration.

For the front mount replacement: 1. Raise the vehicle and remove the splash shield. 2. Support the engine with a block of wood. 3. Remove the front mount through-bolt and crossmember-to-mount bolts. 4. Take out the mount. 5. If the mount bracket needs replacement, remove the bracket-to-block bolts. 6. Installation follows the reverse order.

To check the mounts, the engine must be raised slightly to relieve weight from them. Begin by raising the vehicle and securely supporting it on jackstands, then remove the front wheels and tires. Position two jacks, one under the crankshaft pulley and the other under the transaxle bellhousing, using a block of wood to protect the components while raising the engine/transaxle just enough to relieve the mounts. Inspect the mounts for any cracks, hardening, or separation from the metal plates, and check for movement between the mount plates and the engine or subframe, tightening any loose fasteners as necessary. Applying rubber preservative can help slow deterioration.