How to check and replace powertrain mounts in four cylinder engine on Chrysler Sebring?

There are four powertrain mounts, the front mount connects the transaxle to the crossmember; the left mount secures the driver's side of the engine to the subframe; the right engine mount attaches the engine block to the passenger's side of the subframe; and a rear mount links the engine block to the subframe. To check the mounts, the engine must be raised slightly to relieve weight from them. Begin by raising the vehicle and securely supporting it on jackstands, then remove the front wheels and tires. Position two jacks, one under the crankshaft pulley and the other under the transaxle bellhousing, using a block of wood to protect the components while raising the engine/transaxle just enough to relieve the mounts. Inspect the mounts for any cracks, hardened rubber, or separation from the metal plates, and check for movement between the mount plates and the engine or subframe, tightening any loose fasteners as necessary. Applying rubber preservative can help slow deterioration. For the front mount replacement, raise the vehicle, remove the splash shield, support the engine with a block of wood, and remove the front mount through-bolt and crossmember-to-mount bolts before taking out the mount. If the mount bracket needs replacement, remove the bracket-to-block bolts. Installation follows the reverse order. For the left mount, disconnect the negative battery cable, raise the vehicle, remove the throttle body air inlet tube and air filter housing, support the transaxle, and raise it to relieve weight from the mount. Remove the mount-to-transaxle and mount-to-body bolts, replace the mount, and tighten the bolts to the specified torque. The installation follows the reverse order. For the right mount, remove the coolant reservoir and power steering line bracket fastener, raise the vehicle, and support the engine. Remove the engine mount bracket bolts and the engine mount bolts, then replace the mount and tighten the mount-to-body bolts to the specified torque before lowering the engine and tightening the mount-to-bracket bolts. The installation follows the reverse order. For the rear mount, raise the vehicle, remove the engine splash shield and downstream oxygen sensor, support the engine, and remove the rear mount bracket-to-subframe bolts and the mount through-bolt. Remove the mount by twisting it slightly, install the new mount into the bracket, and tighten the through-bolt by hand. Align the mount to the subframe, install and tighten the bolts to the specified torque, and finish by tightening the through bolt. The installation follows the reverse order.

Genuine Chrysler Sebring Engine Mount

Engine Motor Mount

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

43 Engine Mounts found

View related parts
Chrysler Sebring Support-Engine Mount
Part Number: 4573775AB
$159.79 MSRP: $254.00
You Save: $94.21 (38%)
ADD TO CART
Product Specifications
- Other Name: Support Engine Mount
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2003-2006 Chrysler Sebring | Base Convertible, Base Sedan, GTC Convertible, Limited Convertible, Limited Sedan, LX Convertible, LX Sedan, LXi Convertible, LXi Sedan, Touring Convertible, Touring Sedan, TSI Sedan | 4 Cyl 2.4L, 6 Cyl 2.7L
View related parts
Chrysler Sebring Bushing
Part Number: 5085079AC
$172.17 MSRP: $260.00
You Save: $87.83 (34%)
ADD TO CART
Product Specifications
- Other Name: Engine Mount Rear
- Replaced by: 5085079AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2010 Chrysler Sebring | Limited Sedan, LX Convertible, Touring Sedan | 4 Cyl 2.4L
View related parts
Chrysler Sebring Insulator
Part Number: 5105450AB
$196.77 MSRP: $297.00
You Save: $100.23 (34%)
ADD TO CART
Product Specifications
- Other Name: ISOLATOR; Mount Insulator, Side Mount
- Replaces: 5105450AA, 5085082AB, 5085082AA, 5085492AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2010 Chrysler Sebring | LX Convertible, LX Sedan, Limited Convertible, Limited Sedan, Touring Sedan | 4 Cyl 2.4L, 6 Cyl 2.7L
View related parts
Chrysler Sebring Bracket-Engine Mount
Part Number: 4743960AC
$82.33 MSRP: $127.00
You Save: $44.67 (36%)
ADD TO CART
Product Specifications
- Other Name: Bracket Engine Mount; Mount Brace, Rear Bracket
- Replaces: 4743960AA, 4743960AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008 Chrysler Sebring | Limited Sedan | 6 Cyl 3.5L
View related parts
Chrysler Sebring Support-Engine Mount
Part Number: 5085483AA
$68.32 MSRP: $104.00
You Save: $35.68 (35%)
ADD TO CART
Product Specifications
- Other Name: Support Engine Mount
- Replaced by: 5085071AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2008 Chrysler Sebring | Limited Convertible, LX Convertible | 4 Cyl 2.4L
View related parts
Chrysler Sebring Bracket-Engine Mount
Part Number: 5085074AE
$109.45 MSRP: $164.00
You Save: $54.55 (34%)
ADD TO CART
Product Specifications
- Other Name: Bracket Engine Mount; Mount Brace
- Replaces: 5085074AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2010 Chrysler Sebring | Limited Convertible, Limited Sedan, LX Convertible, LX Sedan, Touring Convertible, Touring Sedan | 4 Cyl 2.4L, 6 Cyl 2.7L
View related parts
Chrysler Sebring Bracket-Engine Mount
Part Number: 5273373AD
$96.32 MSRP: $146.00
You Save: $49.68 (35%)
ADD TO CART
Product Specifications
- Other Name: Bracket Engine Mount
- Replaced by: 5273373AE
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2010 Chrysler Sebring | Limited Convertible, Limited Sedan, LX Convertible, LX Sedan, Touring Sedan | 4 Cyl 2.4L
View related parts
Chrysler Sebring Bracket-Engine Mount
Part Number: 5085472AD
$22.79 MSRP: $29.00
You Save: $6.21 (22%)
ADD TO CART
Product Specifications
- Other Name: Bracket Engine Mount
- Replaces: 5085472AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2010 Chrysler Sebring | LX Sedan, Limited Convertible, Limited Sedan, Touring Sedan | 4 Cyl 2.4L, 6 Cyl 2.7L
View related parts
Chrysler Sebring Bracket-Engine Mount
Part Number: 4593455AA
$89.00 MSRP: $103.00
You Save: $14.00 (14%)
ADD TO CART
Product Specifications
- Other Name: Bracket Engine Mount; Engine Bracket, Mount Bracket, Strut Bracket
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2000 Chrysler Sebring
View related parts
Chrysler Sebring INSULATOR-Engine Mount
Part Number: MR197992
$107.01 MSRP: $136.18
You Save: $29.17 (22%)
ADD TO CART
Product Specifications
- Other Name: DAMPER Engine Mount; Dynamic Damper, Motor Mount Damper
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1998-2005 Chrysler Sebring | LX, LXi | 6 Cyl 2.5L, 6 Cyl 3.0L
- 1995-1996 Chrysler Sebring | LX, LXi | 6 Cyl 2.5L
View related parts
Chrysler Sebring Support-Engine Support
Part Number: 4593383AB
$242.35 MSRP: $310.00
You Save: $67.65 (22%)
ADD TO CART
Product Specifications
- Other Name: Module Engine Support; Engine Support, Front Mount, Front Support
- Replaces: 4593383AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2006 Chrysler Sebring | Base Convertible, Base Sedan, GTC Convertible, LX Convertible, LX Sedan, LXi Convertible, LXi Sedan, Limited Convertible, Limited Sedan, TSI Sedan, Touring Convertible, Touring Sedan | 4 Cyl 2.4L, 6 Cyl 2.7L
View related parts
Chrysler Sebring Support-Engine Support
Part Number: 4593410
$167.67 MSRP: $213.36
You Save: $45.69 (22%)
ADD TO CART
Product Specifications
- Other Name: SCREW/Washer, Right Engine Mount; Engine Support, Module, Support
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1996 Chrysler Sebring | JX, JXi | 4 Cyl 2.4L, 6 Cyl 2.5L
View related parts
Chrysler Sebring Support-Engine Support
Part Number: 4593337AB
$259.38 MSRP: $330.07
You Save: $70.69 (22%)
ADD TO CART
Product Specifications
- Other Name: Module Engine Support; Engine Support, Rear Mount, Rear Support
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2006 Chrysler Sebring | Base Convertible, Base Sedan, GTC Convertible, Limited Convertible, Limited Sedan, LX Convertible, LX Sedan, LXi Convertible, LXi Sedan, Touring Convertible, Touring Sedan, TSI Sedan | 4 Cyl 2.4L, 6 Cyl 2.7L
View related parts
Chrysler Sebring Support-Engine Support
Part Number: 4593383AA
$208.68 MSRP: $310.00
You Save: $101.32 (33%)
ADD TO CART
Product Specifications
- Other Name: Module Engine Support
- Replaced by: 4593383AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2003 Chrysler Sebring | GTC Convertible, Limited Convertible, LX Convertible, LX Sedan, LXi Convertible, LXi Sedan | 4 Cyl 2.4L, 6 Cyl 2.7L
View related parts
Chrysler Sebring Support-Engine Mount
Part Number: 4578001AB
$393.30 MSRP: $582.00
You Save: $188.70 (33%)
ADD TO CART
Product Specifications
- Other Name: Support Engine Mount
- Replaced by: 4573773AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2004-2006 Chrysler Sebring | Base Convertible, GTC Convertible, Limited Convertible, LX Convertible, LXi Convertible, Touring Convertible | 4 Cyl 2.4L, 6 Cyl 2.7L
View related parts
Chrysler Sebring Bracket-Engine Mount
Part Number: 5085471AD
$45.65 MSRP: $58.15
You Save: $12.50 (22%)
ADD TO CART
Product Specifications
- Other Name: Bracket Engine Mount
- Replaces: 5085471AC
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2010 Chrysler Sebring | Limited Convertible, Limited Sedan, LX Sedan, Touring Sedan | 4 Cyl 2.4L, 6 Cyl 2.7L
View related parts
Chrysler Sebring Bracket-Engine Mount
Part Number: 5085517AE
$33.15 MSRP: $67.60
You Save: $34.45 (51%)
ADD TO CART
Product Specifications
- Other Name: Bracket Engine Mount; Mount Brace, Mount Bracket, Rear Bracket
- Replaces: 5085517AD
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2008-2010 Chrysler Sebring | Limited Convertible, Limited Sedan, Touring Sedan | 6 Cyl 3.5L
View related parts
Chrysler Sebring Bracket-Engine Mount
Part Number: 5085513AC
$56.51 MSRP: $71.95
You Save: $15.44 (22%)
ADD TO CART
Product Specifications
- Other Name: Bracket Engine Mount
- Replaces: 5085513AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2009 Chrysler Sebring | Limited Sedan, Touring Sedan
View related parts
Chrysler Sebring Support-Engine Support
Part Number: 4593337AF
$86.26 MSRP: $109.77
You Save: $23.51 (22%)
ADD TO CART
Product Specifications
- Other Name: Module Engine Support; Engine Support, Module, Rear Mount
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1998 Chrysler Sebring | JX, JXi | 4 Cyl 2.4L, 6 Cyl 2.5L
View related parts
Chrysler Sebring Bracket-Engine Mount
Part Number: 5085075AD
Product Specifications
- Other Name: Bracket Engine Mount; Mount Bracket
- Replaces: 5085075AC, 5085075AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007-2010 Chrysler Sebring | LX Convertible, LX Sedan, Limited Convertible, Limited Sedan, Touring Convertible, Touring Sedan | 6 Cyl 2.7L

| Page 1 of 3 |Next >

1-20 of 43 Results

Chrysler Sebring Engine Mount

The Engine Mount in Chrysler Sebring vehicles serves two primary functions: It reduces noise and vibration from the engine and locates as well as supports the engine and transaxle within the chassis. Comfort is central to this isolation while the position and orientation of the engine are important in ensuring safety and to avoid physical destruction. Throughout the evolution of Chrysler Sebring vehicles they have been outfitted with different Engine Mounts such as simple rubber mounts, fluid filled hydraulic mounts, and most recently electronic active mounts. The traditional type contacts include metal parts placed in between rubber spacer while the hydraulic type reduces vibration. Maintenance active mounts are able to change their rigidity in relation with the number of revolutions per minute produced by the engine. These Engine Mounts degrade over time, under extreme heat and if exposed to fluids, which manifest in odd noise and vibration, thus requiring a check in, or replacement.

Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Chrysler Sebring Engine Mount at great affordable prices. Moreover, all genuine Chrysler Sebring Engine Mount come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.

Chrysler Sebring Engine Mount Parts Questions & Experts Answers

Bushing
5085079AC
Q: How to check and replace powertrain mounts in four cylinder engine on Chrysler Sebring?
A: There are four powertrain mounts, the front mount connects the transaxle to the crossmember; the left mount secures the driver's side of the engine to the subframe; the right engine mount attaches the engine block to the passenger's side of the subframe; and a rear mount links the engine block to the subframe. To check the mounts, the engine must be raised slightly to relieve weight from them. Begin by raising the vehicle and securely supporting it on jackstands, then remove the front wheels and tires. Position two jacks, one under the crankshaft pulley and the other under the transaxle bellhousing, using a block of wood to protect the components while raising the engine/transaxle just enough to relieve the mounts. Inspect the mounts for any cracks, hardened rubber, or separation from the metal plates, and check for movement between the mount plates and the engine or subframe, tightening any loose fasteners as necessary. Applying rubber preservative can help slow deterioration. For the front mount replacement, raise the vehicle, remove the splash shield, support the engine with a block of wood, and remove the front mount through-bolt and crossmember-to-mount bolts before taking out the mount. If the mount bracket needs replacement, remove the bracket-to-block bolts. Installation follows the reverse order. For the left mount, disconnect the negative battery cable, raise the vehicle, remove the throttle body air inlet tube and air filter housing, support the transaxle, and raise it to relieve weight from the mount. Remove the mount-to-transaxle and mount-to-body bolts, replace the mount, and tighten the bolts to the specified torque. The installation follows the reverse order. For the right mount, remove the coolant reservoir and power steering line bracket fastener, raise the vehicle, and support the engine. Remove the engine mount bracket bolts and the engine mount bolts, then replace the mount and tighten the mount-to-body bolts to the specified torque before lowering the engine and tightening the mount-to-bracket bolts. The installation follows the reverse order. For the rear mount, raise the vehicle, remove the engine splash shield and downstream oxygen sensor, support the engine, and remove the rear mount bracket-to-subframe bolts and the mount through-bolt. Remove the mount by twisting it slightly, install the new mount into the bracket, and tighten the through-bolt by hand. Align the mount to the subframe, install and tighten the bolts to the specified torque, and finish by tightening the through bolt. The installation follows the reverse order.

Related Chrysler Sebring Parts

Browse by Year

2010 Engine Mount 2009 Engine Mount 2008 Engine Mount 2007 Engine Mount 2006 Engine Mount 2005 Engine Mount 2004 Engine Mount 2003 Engine Mount 2002 Engine Mount 2001 Engine Mount 2000 Engine Mount 1999 Engine Mount 1998 Engine Mount 1997 Engine Mount 1996 Engine Mount 1995 Engine Mount