Chrysler 5139099AA Cylinder-Door Lock

You can Select Your Vehicle to check if 5139099AA fits your vehicle.

Disconnect the cable from the remote ground terminal or battery. Remove the door trim panel. Disconnect the door harness connector from the body harness. Disconnect the window glass from the window regulator and remove the window glass. Release the clips securing the linkage to the door latch, and disconnect the linkages from the door latch. Remove the fasteners securing the door module and remove the door module. Installation is the reverse of removal. Raise the window to the full-up position. Remove the door trim panel. Remove the rubber door latch access cover located on the door module. Remove the latch retaining screws. Disconnect the exterior door handle and lock cylinder linkage from the latch. If working on the driver's door, disconnect the lock cylinder linkage at the latch. Push upward on the latch locator bracket to release the bracket from the door module. Remove the interior door handle release cable from the door latch. Disconnect the electrical connector to the door latch. Remove the latch from the vehicle. Installation is the reverse of removal. Raise the window to the full-up position. Remove the door trim panel. Disconnect the latch rods from the door handle and lock cylinder. Remove the fasteners securing the door handle to the outer door panel and remove the handle from the vehicle. Installation is the reverse of removal. Remove the front door outside handle and pull the lock cylinder from the door handle. Installation is the reverse of removal.

Disconnect the cable from the remote ground terminal or battery. Remove the door trim panel. Disconnect the door harness connector from the body harness. Disconnect the window glass from the window regulator and remove the window glass. Release the clips securing the linkage to the door latch, and disconnect the linkages from the door latch. Remove the fasteners securing the door module and remove the door module. Installation is the reverse of removal. Raise the window to the full-up position. Remove the door trim panel. Remove the rubber door latch access cover located on the door module. Remove the latch retaining screws. Disconnect the exterior door handle and lock cylinder linkage from the latch. If working on the driver's door, disconnect the lock cylinder linkage at the latch. Push upward on the latch locator bracket to release the bracket from the door module. Remove the interior door handle release cable from the door latch. Disconnect the electrical connector to the door latch. Remove the latch from the vehicle. Installation is the reverse of removal. Raise the window to the full-up position. Remove the door trim panel. Disconnect the latch rods from the door handle and lock cylinder. Remove the fasteners securing the door handle to the outer door panel and remove the handle from the vehicle. Installation is the reverse of removal. Remove the front door outside handle and pull the lock cylinder from the door handle. Installation is the reverse of removal.

To replace the latch, first, the window has to be lifted as far as possible; then, the door trim panel and watershield have to be taken off. Then, detach the door speaker and also those at the rear glass run channel and pull the channel away from the latch to provide more working space. Turn the two plastic retaining clips out of the rods and free the latch links and, then, release the electrical connection. To dismantle this part, one has to take out the three mounting screws that may need an impact-type screwdriver to be unscrewed from the door; the latch can then be removed. Align installation of new latch, and place the screws accordingly make them tight; reconnect the link rods also connect the electrical connector. The process of installation is in direct relation with removal and is the process that is repeated but in the opposite manner. For the lock cylinder, take off the outside door handle, and pull the lock cylinder out of the handle, while to install, do the vice versa. To replace outside handle, remove the door trim panel and speaker, then the fasteners at the rear glass run channel should be remove and shifted from the latch. Take the aerodynamic fasteners of the outside handle, turn the link rods and unfasten the handle from the door. Put the new handle in its appropriate position and fasten the link to it, and the nuts to the link provided that the bolts be tightened to the required standard of tightness, that is the reverse of the process of removal.

Raise the window completely and remove the door trim panel and water shield. Remove the door speaker. Remove the fasteners at the rear glass run channel and move the channel away from the latch (Remove the fasteners securing the pull cup bracket). This provides a little extra working room in the latch area inside the door. Rotate the plastic retaining clips off the rods, then detach the latch links. Disconnect the electrical connector. Remove the three mounting screws (it may be necessary to use an impact-type screwdriver to loosen them), then remove the latch from the door ( Remove the latch mounting screws). Place the latch in position and install the screws. Tighten the screws securely. Connect the link rods and electrical connector to the latch. The remainder of installation is the reverse of removal. Remove the outside door handle. Withdraw the lock cylinder from the door handle. Installation is the reverse of removal. Remove the door trim panel. Remove the door speaker. Remove the fasteners at the rear glass run channel and move the channel away from the latch. This provides a little extra working room in the latch area inside the door. Disconnect the link rods from the outside handle, remove the mounting fasteners and carefully detach the handle from the door. Place the handle in position, attach the link and install the nuts. Tighten the fasteners securely. The remainder of installation is the reverse of removal.

Raise the window completely and remove the door trim panel and water shield. Remove the door speaker. Remove the fasteners at the rear glass run channel and move the channel away from the latch (Remove the fasteners securing the pull cup bracket). This provides a little extra working room in the latch area inside the door. Rotate the plastic retaining clips off the rods, then detach the latch links. Disconnect the electrical connector. Remove the three mounting screws (it may be necessary to use an impact-type screwdriver to loosen them), then remove the latch from the door ( Remove the latch mounting screws). Place the latch in position and install the screws. Tighten the screws securely. Connect the link rods and electrical connector to the latch. The remainder of installation is the reverse of removal. Remove the outside door handle. Withdraw the lock cylinder from the door handle. Installation is the reverse of removal. Remove the door trim panel. Remove the door speaker. Remove the fasteners at the rear glass run channel and move the channel away from the latch. This provides a little extra working room in the latch area inside the door. Disconnect the link rods from the outside handle, remove the mounting fasteners and carefully detach the handle from the door. Place the handle in position, attach the link and install the nuts. Tighten the fasteners securely. The remainder of installation is the reverse of removal.

Raise the window completely and remove the door trim panel and water shield. Remove the door speaker. Remove the fasteners at the rear glass run channel and move the channel away from the latch (Remove the fasteners securing the pull cup bracket). This provides a little extra working room in the latch area inside the door. Rotate the plastic retaining clips off the rods, then detach the latch links. Disconnect the electrical connector. Remove the three mounting screws (it may be necessary to use an impact-type screwdriver to loosen them), then remove the latch from the door ( Remove the latch mounting screws). Place the latch in position and install the screws. Tighten the screws securely. Connect the link rods and electrical connector to the latch. The remainder of installation is the reverse of removal. Remove the outside door handle. Withdraw the lock cylinder from the door handle. Installation is the reverse of removal. Remove the door trim panel. Remove the door speaker. Remove the fasteners at the rear glass run channel and move the channel away from the latch. This provides a little extra working room in the latch area inside the door. Disconnect the link rods from the outside handle, remove the mounting fasteners and carefully detach the handle from the door. Place the handle in position, attach the link and install the nuts. Tighten the fasteners securely. The remainder of installation is the reverse of removal.

Before removing the door module, raise the window to the full-up position to ensure that it is properly secured.

Disconnect the link rods from the latch and remove the three Torx-head mounting screws, using an impact-type screwdriver if necessary.