Make sure this part fits

Chrysler 4591862AI Plenum-Intake Manifold

2008-2009 Chrysler 300 4591862AI

Customer Questions & Expert Answers (10)
Mopar 4591862AI Plenum-Intake Manifold
  • Part Description
    PLENUM Intake Manifold
  • Replaced By
    4591862AK
  • Manufacturer
    Mopar
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits
  • Related Parts
  • Product Specifications
  • Vehicle Fitment
  • Customer Questions & Expert Answers
  • Product Specifications

    BrandGenuine Chrysler
    Manufacturer Part Number4591862AI
    Part DescriptionPLENUM Intake Manifold
    Item Dimensions35.0 x 31.2 x 8.2 inches
    Item Weight16.50 Pounds
    ConditionNew
    ManufacturerMopar
    SKU4591862AI
    WarrantyThis genuine Mopar part is guaranteed by Mopar's factory warranty.
    Shipping & ReturnShipping Policy Return Policy
    Warning: California’s Proposition 65
  • Vehicle Fitment

    Year Make Model Engine Important vehicle option details
    2008-2009 Chrysler 3006 Cyl 2.7LC AWD, C RWD, LX RWD
  • Customer Questions & Expert Answers

    Q:
    This part will not fit my vehicle. Can you provide me with the part number for the bracket that will fit? TN. Posted by MoparPartsGiant Specialist
    A:
    You can Select Your Vehicle to check if 4591862AI fits your vehicle.
    Posted by MoparPartsGiant Specialist
    Q:
    How do you remove the upper intake manifold for the 2007 Chrysler 300? Posted by Customer
    A:
    To remove the upper intake manifold, start by relieving the fuel system pressure and disconnecting the battery cable. Then, remove the air filter housing and label and disconnect the hoses and electrical connectors attached to the intake manifold and throttle body. Remove the bolts securing the EGR pipe and the brackets from the throttle body and upper intake manifold. Loosen the upper intake manifold bolts and lift the manifold from the engine. Clean the mounting surfaces and inspect the O-ring gasket. If it's in good condition, it can be reused. Install the gasket into the groove in the upper intake manifold and then install the manifold onto the lower intake manifold, tightening the bolts in a circular pattern.
    Posted by MoparPartsGiant Specialist
    Q:
    What should be done with the vacuum hoses and electrical connectors attached to the upper intake manifold and throttle body for the 2007 Chrysler 300? Posted by Customer
    A:
    Label and disconnect the vacuum hoses and electrical connectors attached to the upper intake manifold and throttle body, including the electronic throttle control system.
    Posted by MoparPartsGiant Specialist
    See expert answers on similar Intake Manifold
    Q:
    What components should be removed after the air filter housing and intake air duct for the 2010 Chrysler 300? Posted by Customer
    A:
    Remove the ignition coils and, on 2005 models, the spark plug wires.
    Posted by MoparPartsGiant Specialist
    Q:
    What is the procedure for installing the upper intake manifold for the 2006 Dodge Charger? Posted by Customer
    A:
    To install the upper intake manifold, align it with the lower intake manifold and tighten the bolts according to the specified torque.
    Posted by MoparPartsGiant Specialist
    Q:
    How should the intake manifold bolts be loosened during removal for the 2010 Dodge Charger? Posted by Customer
    A:
    Starting with the outer bolts and working to the inner bolts, loosen the intake manifold bolts in 1/4-turn increments until they can be removed by hand. Follow the reverse of the tightening sequence.
    Posted by MoparPartsGiant Specialist
    Q:
    How do you remove the lower intake manifold for the 2009 Dodge Charger? Posted by Customer
    A:
    To remove the lower intake manifold, drain the cooling system and remove the upper intake manifold. Label and detach any remaining hoses and remove the fuel rail and injectors. Remove the heater hoses and coolant hoses. Loosen the remaining manifold mounting bolts/nuts and carefully break the gasket seal. Turn the manifold over, replace the O-ring on the heater supply tube, and remove all traces of old gasket material and sealant. Clean the mating surfaces with lacquer thinner or acetone. Apply RTV sealant around the front and rear cylinder head water passages and lay the new gaskets in place. Position the manifold on the engine, aligning the gaskets and manifold with the ports in the cylinder heads. Install the fuel rail and injectors, then tighten the nuts/bolts following the recommended sequence. Refill the cooling system, run the engine, and check for leaks.
    Posted by MoparPartsGiant Specialist
    See expert answers on similar Intake Manifold
    Q:
    What is the first step to start the process of removing the intake manifold for the 2006 Dodge Magnum? Posted by Customer
    A:
    Remove the engine cover.
    Posted by MoparPartsGiant Specialist
    See expert answers on similar Intake Manifold
    Q:
    How do you remove the lower intake manifold for the 2007 Dodge Magnum? Posted by Customer
    A:
    To remove the lower intake manifold, drain the cooling system and remove the upper intake manifold. Label and detach any remaining hoses and remove the fuel rail and injectors. Remove the heater hoses and coolant hoses. Loosen the remaining manifold mounting bolts/nuts and carefully break the gasket seal. Turn the manifold over, replace the O-ring on the heater supply tube, and remove all traces of old gasket material and sealant. Clean the mating surfaces with lacquer thinner or acetone. Apply RTV sealant around the front and rear cylinder head water passages and lay the new gaskets in place. Position the manifold on the engine, aligning the gaskets and manifold with the ports in the cylinder heads. Install the fuel rail and injectors, then tighten the nuts/bolts following the recommended sequence. Refill the cooling system, run the engine, and check for leaks.
    Posted by MoparPartsGiant Specialist
    Q:
    How should the lower intake manifold mounting bolts/nuts be handled for the 2005 Dodge Magnum? Posted by Customer
    A:
    Loosen the lower intake manifold mounting bolts/nuts in reverse order until they can be removed by hand. Carefully break the gasket seal without prying between the manifold and the heads.
    Posted by MoparPartsGiant Specialist
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

Genuine Mopar Part 4591862AI, the Right Choice

To ensure reliability, purchase Mopar part # 4591862AI Plenum-Intake Manifold. It is sometimes referred to as Chrysler Intake Manifold. For Mopar owners with dreams of keeping their vehicles running in prime condition, choosing OEM parts is a smart decision. Meticulously crafted, these parts follow strict factory specifications and are manufactured in top-notch facilities with advanced technologies. Furthermore, they undergo rigorous testing to ensure durability and safety, making them a reliable choice for Mopar owners. This part fits specific Chrysler 300 models.

MoparPartsGiant.com is a leading supplier of genuine Mopar parts and accessories such as Mopar 4591862AI Plenum-Intake Manifold. Wondering where to find exceptional quality and affordable OEM Mopar parts? You have already come to the right place. Our website boasts a huge selection of genuine Mopar parts at the most economical prices possible. What's more, all parts come with a manufacturer's warranty. For detailed Chrysler parts information, click here.

Why choose Mopar Parts Giant

  • Dedicated Service

    Your complete satisfaction is our #1 goal

  • Lowest Prices

    Best deals on genuine OE parts from dealerships

  • Fast Delivery

    Orders are processed and delivered promptly