Make sure this part fits

Chrysler 4606093AE Sensor-Knock

2008-2010 Chrysler 4606093AE

Customer Questions & Expert Answers (9)
Mopar 4606093AE Sensor-Knock
  • Part Description
    Sensor Knock
  • Replaced By
    4606093AF
  • Manufacturer
    Mopar
Make sure this part fits
$106.82 MSRP: $162.00
You Save: $55.18 (35%)
1
ADD TO CART
  • Related Parts
  • Product Specifications
  • Vehicle Fitment
  • Customer Questions & Expert Answers
  • Product Specifications

    BrandGenuine Chrysler
    Manufacturer Part Number4606093AE
    Part DescriptionSensor Knock
    Item Dimensions1.4 x 3.3 x 9.3 inches
    Item Weight0.50 Pounds
    ConditionNew
    Fitment TypeDirect Replacement
    ManufacturerMopar
    SKU4606093AE
    WarrantyThis genuine Mopar part is guaranteed by Mopar's factory warranty.
    Shipping & ReturnShipping Policy Return Policy
    Warning: California’s Proposition 65
  • Vehicle Fitment

    Year Make Model Engine Important vehicle option details
    2008-2009 Chrysler Aspen8 Cyl 4.7LLimited 2WD, Limited 4WD
    2008 Chrysler Pacifica6 Cyl 4.0LLimited AWD, Limited FWD, LX AWD, Touring AWD, Touring FWD
    2008-2010 Chrysler Town & Country6 Cyl 4.0LLimited, LX, Touring, Touring Plus
  • Customer Questions & Expert Answers

    Q:
    This part will not fit my vehicle. Can you provide me with the part number for the bracket that will fit? TN. Posted by MoparPartsGiant Specialist
    A:
    You can Select Your Vehicle to check if 4606093AE fits your vehicle.
    Posted by MoparPartsGiant Specialist
    Q:
    How do you replace the knock sensors for the 2008 Dodge Durango? Posted by Customer
    A:
    To replace them, start by disconnecting the cable from the negative battery terminal. Then, disconnect the knock sensor electrical connector, which is located at the rear of the engine, behind the intake manifold. Remove the intake manifold and then remove the knock sensor assembly by taking out the mounting bolts. Make sure to clean the holes for the mounting bolts before installing the new knock sensor assembly. Note that the left knock sensor is identified by an identification tag and has a larger mounting bolt, so do not switch the knock sensors.
    Posted by MoparPartsGiant Specialist
    See expert answers on similar Knock Sensor
    Q:
    Where are the knock sensors located for the 2009 Dodge Dakota? Posted by Customer
    A:
    The knock sensors for the 3.7L V6 and 4.7L V8 engines are located on top of the block in the valley between the cylinder heads, underneath the intake manifold.
    Posted by MoparPartsGiant Specialist
    See expert answers on similar Knock Sensor
    Q:
    How is the charge temperature sensor replaced for the 1994 Dodge Grand Caravan? Posted by Customer
    A:
    For the charge temperature sensor, unplug the electrical connector, unscrew the sensor, coat the threads of the new sensor with tape, and install it securely.
    Posted by MoparPartsGiant Specialist
    See expert answers on similar Knock Sensor
    Q:
    How do you disconnect the knock sensors for the 2010 Dodge Ram 1500? Posted by Customer
    A:
    Start by disconnecting the cable(s) from the negative battery terminal(s). For the 3.6L V6 engine, remove the intake manifolds and then disconnect the electrical connector(s) before removing the sensor(s) mounting bolt(s). For the 3.7L V6 and 4.7L V8 engines, remove the intake manifold and then disconnect the knock sensor electrical connector located at the rear of the engine, behind the intake manifold. For HEMI engines, raise the front of the vehicle and secure it on jackstands. Disconnect the electrical connector from the knock sensor and remove the knock sensor mounting bolt. Finally, install the knock sensor(s) by reversing the removal process and tightening the mounting bolts.
    Posted by MoparPartsGiant Specialist
    See expert answers on similar Knock Sensor
    Q:
    How do you remove the knock sensors for the 2007 Dodge Nitro? Posted by Customer
    A:
    Disconnect the knock sensor electrical connector located near the rear of the left valve cover. Remove the intake manifold. Remove the knock sensor mounting bolts and remove the sensors. Thoroughly clean the bolts and bolt holes.
    Posted by MoparPartsGiant Specialist
    See expert answers on similar Knock Sensor
    Q:
    How do you install the knock sensors for the 2003 Jeep Liberty? Posted by Customer
    A:
    Install the knock sensors and tighten the mounting bolts to 15 ft-lbs (20 Nm). Do not apply sealant to the bolts. It is important to properly torque the mounting bolts to ensure proper knock sensor operation and accurate ignition timing control. Installation is the reverse of removal.
    Posted by MoparPartsGiant Specialist
    See expert answers on similar Knock Sensor
    Q:
    How do you replace the knock sensors for the 2011 Jeep Grand Cherokee? Posted by Customer
    A:
    For Hemi engines, there are two knock sensors located on the left and right sides of the block below the exhaust manifold. To replace them, raise the front of the vehicle and secure it on jackstands. Disconnect the electrical connector from the knock sensor and remove the mounting bolt. Installation is the reverse of removal, making sure to tighten the mounting bolts to the correct torque.
    Posted by MoparPartsGiant Specialist
    See expert answers on similar Knock Sensor
    Q:
    How do you disconnect the knock sensors for the 2011 Ram 1500? Posted by Customer
    A:
    Start by disconnecting the cable(s) from the negative battery terminal(s). For the 3.6L V6 engine, remove the intake manifolds and then disconnect the electrical connector(s) before removing the sensor(s) mounting bolt(s). For the 3.7L V6 and 4.7L V8 engines, remove the intake manifold and then disconnect the knock sensor electrical connector located at the rear of the engine, behind the intake manifold. For HEMI engines, raise the front of the vehicle and secure it on jackstands. Disconnect the electrical connector from the knock sensor and remove the knock sensor mounting bolt. Finally, install the knock sensor(s) by reversing the removal process and tightening the mounting bolts.
    Posted by MoparPartsGiant Specialist
    See expert answers on similar Knock Sensor
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

Genuine Mopar Part 4606093AE, the Right Choice

To ensure reliability, purchase Mopar part # 4606093AE Sensor-Knock. It is sometimes referred to as Chrysler Knock Sensor. For Mopar owners with dreams of keeping their vehicles running in prime condition, choosing OEM parts is a smart decision. Meticulously crafted, these parts follow strict factory specifications and are manufactured in top-notch facilities with advanced technologies. Furthermore, they undergo rigorous testing to ensure durability and safety, making them a reliable choice for Mopar owners. This part fits specific Chrysler Aspen, Pacifica, Town & Country models.

MoparPartsGiant.com is a leading supplier of genuine Mopar parts and accessories such as Mopar 4606093AE Sensor-Knock. Wondering where to find exceptional quality and affordable OEM Mopar parts? You have already come to the right place. Our website boasts a huge selection of genuine Mopar parts at the most economical prices possible. What's more, all parts come with a manufacturer's warranty. For detailed Chrysler parts information, click here.

Why choose Mopar Parts Giant

  • Dedicated Service

    Your complete satisfaction is our #1 goal

  • Lowest Prices

    Best deals on genuine OE parts from dealerships

  • Fast Delivery

    Orders are processed and delivered promptly