Make sure this part fits

Jeep 5139099AA Cylinder-Door Lock

2007-2022 Jeep 5139099AA

Customer Questions & Expert Answers (9)
Mopar 5139099AA Cylinder-Door Lock
  • Part Description
    Cylinder Door Lock
  • Manufacturer
    Mopar
Make sure this part fits
$69.77 MSRP: $104.00
You Save: $34.23 (33%)
1
ADD TO CART
  • Related Parts
  • Product Specifications
  • Vehicle Fitment
  • Customer Questions & Expert Answers
  • Product Specifications

    BrandGenuine Jeep
    Manufacturer Part Number5139099AA
    Part DescriptionCylinder Door Lock
    Other NamesLock Cylinder
    Item Dimensions4.8 x 3.6 x 1.0 inches
    Item Weight0.50 Pounds
    ConditionNew
    ManufacturerMopar
    SKU5139099AA
    WarrantyThis genuine Mopar part is guaranteed by Mopar's factory warranty.
    Shipping & ReturnShipping Policy Return Policy
    Warning: California’s Proposition 65
  • Vehicle Fitment

    Year Make Model Engine Important vehicle option details
    2007-2017 Jeep Compass4 Cyl 2.0L, 4 Cyl 2.4LBase 4WD, Base FWD, Latitude 4WD, Latitude FWD, Limited 4WD, Limited FWD, Sport 4WD, Sport FWD
    2011-2022 Jeep Grand Cherokee6 Cyl 3.0L Diesel, 6 Cyl 3.6L, 8 Cyl 5.7L, 8 Cyl 6.2L, 8 Cyl 6.4LLaredo 2WD, Laredo 4WD, Laredo AWD, Laredo RWD, Limited 2WD, Limited 4WD, Limited AWD, Limited RWD, Overland 2WD, Overland 4WD, Overland AWD, Overland RWD, SRT AWD, SRT8 4WD, Summit AWD, Summit RWD, Trackhawk AWD, Trailhawk AWD
    2022 Jeep Grand Cherokee WK6 Cyl 3.6 L FLEX
    2009-2017, 2007 Jeep Patriot4 Cyl 2.0L, 4 Cyl 2.4LBase 4WD, Base FWD, Latitude 4WD, Latitude FWD, Latitude X 4WD, Latitude X FWD, Limited 4WD, Limited FWD, Sport 4WD, Sport FWD
  • Customer Questions & Expert Answers

    Q:
    Will this fit my truck? Posted by MoparPartsGiant Specialist
    A:
    You can Select Your Vehicle to check if 5139099AA fits your vehicle.
    Posted by MoparPartsGiant Specialist
    Q:
    How to remove and install Door Handle,Door Latch Assembly and Door Lock Cylinder on Chrysler Sebring? Posted by Customer
    A:
    Disconnect the cable from the remote ground terminal or battery. Remove the door trim panel. Disconnect the door harness connector from the body harness. Disconnect the window glass from the window regulator and remove the window glass. Release the clips securing the linkage to the door latch, and disconnect the linkages from the door latch. Remove the fasteners securing the door module and remove the door module. Installation is the reverse of removal. Raise the window to the full-up position. Remove the door trim panel. Remove the rubber door latch access cover located on the door module. Remove the latch retaining screws. Disconnect the exterior door handle and lock cylinder linkage from the latch. If working on the driver's door, disconnect the lock cylinder linkage at the latch. Push upward on the latch locator bracket to release the bracket from the door module. Remove the interior door handle release cable from the door latch. Disconnect the electrical connector to the door latch. Remove the latch from the vehicle. Installation is the reverse of removal. Raise the window to the full-up position. Remove the door trim panel. Disconnect the latch rods from the door handle and lock cylinder. Remove the fasteners securing the door handle to the outer door panel and remove the handle from the vehicle. Installation is the reverse of removal. Remove the front door outside handle and pull the lock cylinder from the door handle. Installation is the reverse of removal.
    Posted by MoparPartsGiant Specialist
    Q:
    How to remove and install Door Handle,Door Latch Assembly and Door Lock Cylinder on Dodge Avenger? Posted by Customer
    A:
    Disconnect the cable from the remote ground terminal or battery. Remove the door trim panel. Disconnect the door harness connector from the body harness. Disconnect the window glass from the window regulator and remove the window glass. Release the clips securing the linkage to the door latch, and disconnect the linkages from the door latch. Remove the fasteners securing the door module and remove the door module. Installation is the reverse of removal. Raise the window to the full-up position. Remove the door trim panel. Remove the rubber door latch access cover located on the door module. Remove the latch retaining screws. Disconnect the exterior door handle and lock cylinder linkage from the latch. If working on the driver's door, disconnect the lock cylinder linkage at the latch. Push upward on the latch locator bracket to release the bracket from the door module. Remove the interior door handle release cable from the door latch. Disconnect the electrical connector to the door latch. Remove the latch from the vehicle. Installation is the reverse of removal. Raise the window to the full-up position. Remove the door trim panel. Disconnect the latch rods from the door handle and lock cylinder. Remove the fasteners securing the door handle to the outer door panel and remove the handle from the vehicle. Installation is the reverse of removal. Remove the front door outside handle and pull the lock cylinder from the door handle. Installation is the reverse of removal.
    Posted by MoparPartsGiant Specialist
    Q:
    How do you replace the latch,Lock Cylinder and handle on a door on Dodge Challenger? Posted by Customer
    A:
    To replace the latch, first, the window has to be lifted as far as possible; then, the door trim panel and watershield have to be taken off. Then, detach the door speaker and also those at the rear glass run channel and pull the channel away from the latch to provide more working space. Turn the two plastic retaining clips out of the rods and free the latch links and, then, release the electrical connection. To dismantle this part, one has to take out the three mounting screws that may need an impact-type screwdriver to be unscrewed from the door; the latch can then be removed. Align installation of new latch, and place the screws accordingly make them tight; reconnect the link rods also connect the electrical connector. The process of installation is in direct relation with removal and is the process that is repeated but in the opposite manner. For the lock cylinder, take off the outside door handle, and pull the lock cylinder out of the handle, while to install, do the vice versa. To replace outside handle, remove the door trim panel and speaker, then the fasteners at the rear glass run channel should be remove and shifted from the latch. Take the aerodynamic fasteners of the outside handle, turn the link rods and unfasten the handle from the door. Put the new handle in its appropriate position and fasten the link to it, and the nuts to the link provided that the bolts be tightened to the required standard of tightness, that is the reverse of the process of removal.
    Posted by MoparPartsGiant Specialist
    Q:
    How to remove and install a door latch,Door Lock Cylinder and outside door handle on Chrysler 300? Posted by Customer
    A:
    Raise the window completely and remove the door trim panel and water shield. Remove the door speaker. Remove the fasteners at the rear glass run channel and move the channel away from the latch (Remove the fasteners securing the pull cup bracket). This provides a little extra working room in the latch area inside the door. Rotate the plastic retaining clips off the rods, then detach the latch links. Disconnect the electrical connector. Remove the three mounting screws (it may be necessary to use an impact-type screwdriver to loosen them), then remove the latch from the door ( Remove the latch mounting screws). Place the latch in position and install the screws. Tighten the screws securely. Connect the link rods and electrical connector to the latch. The remainder of installation is the reverse of removal. Remove the outside door handle. Withdraw the lock cylinder from the door handle. Installation is the reverse of removal. Remove the door trim panel. Remove the door speaker. Remove the fasteners at the rear glass run channel and move the channel away from the latch. This provides a little extra working room in the latch area inside the door. Disconnect the link rods from the outside handle, remove the mounting fasteners and carefully detach the handle from the door. Place the handle in position, attach the link and install the nuts. Tighten the fasteners securely. The remainder of installation is the reverse of removal.
    Posted by MoparPartsGiant Specialist
    Q:
    How to remove and install a door latch,Door Lock Cylinder and outside door handle on Dodge Charger? Posted by Customer
    A:
    Raise the window completely and remove the door trim panel and water shield. Remove the door speaker. Remove the fasteners at the rear glass run channel and move the channel away from the latch (Remove the fasteners securing the pull cup bracket). This provides a little extra working room in the latch area inside the door. Rotate the plastic retaining clips off the rods, then detach the latch links. Disconnect the electrical connector. Remove the three mounting screws (it may be necessary to use an impact-type screwdriver to loosen them), then remove the latch from the door ( Remove the latch mounting screws). Place the latch in position and install the screws. Tighten the screws securely. Connect the link rods and electrical connector to the latch. The remainder of installation is the reverse of removal. Remove the outside door handle. Withdraw the lock cylinder from the door handle. Installation is the reverse of removal. Remove the door trim panel. Remove the door speaker. Remove the fasteners at the rear glass run channel and move the channel away from the latch. This provides a little extra working room in the latch area inside the door. Disconnect the link rods from the outside handle, remove the mounting fasteners and carefully detach the handle from the door. Place the handle in position, attach the link and install the nuts. Tighten the fasteners securely. The remainder of installation is the reverse of removal.
    Posted by MoparPartsGiant Specialist
    Q:
    How to remove and install a door latch,Door Lock Cylinder and outside door handle on Dodge Magnum? Posted by Customer
    A:
    Raise the window completely and remove the door trim panel and water shield. Remove the door speaker. Remove the fasteners at the rear glass run channel and move the channel away from the latch (Remove the fasteners securing the pull cup bracket). This provides a little extra working room in the latch area inside the door. Rotate the plastic retaining clips off the rods, then detach the latch links. Disconnect the electrical connector. Remove the three mounting screws (it may be necessary to use an impact-type screwdriver to loosen them), then remove the latch from the door ( Remove the latch mounting screws). Place the latch in position and install the screws. Tighten the screws securely. Connect the link rods and electrical connector to the latch. The remainder of installation is the reverse of removal. Remove the outside door handle. Withdraw the lock cylinder from the door handle. Installation is the reverse of removal. Remove the door trim panel. Remove the door speaker. Remove the fasteners at the rear glass run channel and move the channel away from the latch. This provides a little extra working room in the latch area inside the door. Disconnect the link rods from the outside handle, remove the mounting fasteners and carefully detach the handle from the door. Place the handle in position, attach the link and install the nuts. Tighten the fasteners securely. The remainder of installation is the reverse of removal.
    Posted by MoparPartsGiant Specialist
    Q:
    What should be done to secure the window before removing the door module for the 2011 Chrysler 200? Posted by Customer
    A:
    Before removing the door module, raise the window to the full-up position to ensure that it is properly secured.
    Posted by MoparPartsGiant Specialist
    See expert answers on similar Door Lock Cylinder
    Q:
    How do you disconnect the latch from the door for the 1998 Dodge Grand Caravan? Posted by Customer
    A:
    Disconnect the link rods from the latch and remove the three Torx-head mounting screws, using an impact-type screwdriver if necessary.
    Posted by MoparPartsGiant Specialist
    See expert answers on similar Door Lock Cylinder
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

Genuine Mopar Part 5139099AA, the Right Choice

To ensure reliability, purchase Mopar part # 5139099AA Cylinder-Door Lock. It is sometimes referred to as Jeep Door Lock Cylinder. For Mopar owners with dreams of keeping their vehicles running in prime condition, choosing OEM parts is a smart decision. Meticulously crafted, these parts follow strict factory specifications and are manufactured in top-notch facilities with advanced technologies. Furthermore, they undergo rigorous testing to ensure durability and safety, making them a reliable choice for Mopar owners. This part fits specific Jeep Compass, Grand Cherokee, Patriot models.

MoparPartsGiant.com is a leading supplier of genuine Mopar parts and accessories such as Mopar 5139099AA Cylinder-Door Lock. Wondering where to find exceptional quality and affordable OEM Mopar parts? You have already come to the right place. Our website boasts a huge selection of genuine Mopar parts at the most economical prices possible. What's more, all parts come with a manufacturer's warranty. For detailed Jeep parts information, click here.

Why choose Mopar Parts Giant

  • Dedicated Service

    Your complete satisfaction is our #1 goal

  • Lowest Prices

    Best deals on genuine OE parts from dealerships

  • Fast Delivery

    Orders are processed and delivered promptly