Mopar 5085514AB Bracket-Engine Mount

You can Select Your Vehicle to check if 5085514AB fits your vehicle.

To replace the front mount, raise the vehicle and support the engine with a block of wood. Remove the front mount through-bolt, crossmember-to-mount bolt, and crossmember mounting bolts before removing the mount. If the mount bracket needs replacement, remove the bracket-to-block bolts. The installation follows the reverse order.

For the front mount replacement: 1. Raise the vehicle and remove the splash shield. 2. Support the engine with a block of wood. 3. Remove the front mount through-bolt and crossmember-to-mount bolts. 4. Take out the mount. 5. If the mount bracket needs replacement, remove the bracket-to-block bolts. 6. Installation follows the reverse order.

To replace the front mount, raise the vehicle, remove the crossmember-to-mount bolts, and the through bolt to take out the mount. Then, reverse the process for installation.

There are four powertrain mounts: 1. The front mount connects the transaxle to the crossmember. 2. The left mount secures the driver's side of the engine to the subframe. 3. The right engine mount attaches the engine block to the passenger's side of the subframe. 4. The rear mount links the engine block to the subframe.

To replace the front mount, raise the vehicle, remove the crossmember-to-mount bolts, and the through bolt to take out the mount. Then, reverse the process for installation.

For the rear mount: 1. Raise the vehicle and remove the engine splash shield and downstream oxygen sensor. 2. Support the engine. 3. Remove the rear mount bracket-to-subframe bolts and the mount through-bolt. 4. Remove the mount by twisting it slightly. 5. Install the new mount into the bracket and tighten the through-bolt by hand. 6. Align the mount to the subframe, install and tighten the bolts to the specified torque, and finish by tightening the through bolt. 7. Installation follows the reverse order.

To check the mounts, the engine must be raised slightly to remove the weight from them. This involves securely supporting the vehicle on jackstands, positioning a jack under the engine oil pan with a wood block to prevent damage, and carefully raising the engine.

If movement is noted, the engine should be lowered, and the mount fasteners tightened. Rubber preservative may also be applied to slow deterioration.

To check the mounts, the engine must be raised slightly to relieve weight from them. Begin by raising the vehicle and securely supporting it on jackstands. Then, remove the front wheels and tires. Position two jacks-one under the crankshaft pulley and the other under the transaxle bellhousing-using a block of wood to protect the components while raising the engine/transaxle just enough to relieve the mounts. Inspect the mounts for any cracks, hardened rubber, or separation from the metal plates, and check for movement between the mount plates and the engine or subframe. Tighten any loose fasteners as necessary. Applying rubber preservative can help slow deterioration.

For the left mount replacement, disconnect the negative battery cable, raise the vehicle, and remove the under-vehicle splash shield, throttle body air inlet tube, and air filter housing. Support the transaxle and raise it to relieve weight from the mount. Then, remove the mounting bolts and replace the mount, tightening the bolts to the specified torque. The installation follows the reverse order.

To check the mounts, the engine must be raised slightly to relieve weight from them. Begin by raising the vehicle and securely supporting it on jackstands, then remove the front wheels and tires. Position two jacks, one under the crankshaft pulley and the other under the transaxle bellhousing, using a block of wood to protect the components while raising the engine/transaxle just enough to relieve the mounts. Inspect the mounts for any cracks, hardening, or separation from the metal plates, and check for movement between the mount plates and the engine or subframe, tightening any loose fasteners as necessary. Applying rubber preservative can help slow deterioration.

To replace the front mount, the vehicle must be raised and supported securely, the weight from the mounts must be relieved, and the necessary bolts must be removed to install a new mount.