Mopar 4606869AB Ignition Coil

You can Select Your Vehicle to check if 4606869AB fits your vehicle.

Remove the engine cover(s) as necessary to access the components. Disconnect the negative battery cable from the remote ground terminal or battery. For the 2.4L engine, disconnect the electrical connector from the ignition coil and remove the bolt attaching the ignition coil to the valve cover. Grasp the ignition coil firmly and pull off the spark plug using a twisting motion. Installation is the reverse of removal. For the 2.7L/3.5L V6 engine, remove the upper intake manifold to access the coils. Disconnect the electrical connector from the ignition coil and remove the bolt attaching the ignition coil to the valve cover.

To remove a conventional coil, start by detaching the cable from the negative battery terminal. Then, mark the wires and terminals with numbered tape and remove the primary wires and high-tension cable from the coil. If it's a four-cylinder engine, disconnect the primary electrical connector and high-tension cable, and remove the mounting bolts. For an earlier type coil on the fenderwell, disconnect the primary wires and high-tension cable, and remove the mounting bracket bolts. If the coil is bad, loosen the clamp pinch screw and transfer the clamp/mounting bracket to the new coil. Make sure to release the locking tab on the electrical connector for the primary wires on the later type engine-mounted coil before disconnecting it. On 3.0L engines, remove the mounting bolts from the intake plenum and intake manifold. Disconnect the coil mounting bracket, remove the coil/bracket assembly, clean the outer case, and check for cracks or damage. Clean the coil primary terminals and check the coil tower terminal for corrosion, using a wire brush if necessary. Check the coil primary resistance by attaching the leads of an ohmmeter to the positive and negative terminals. Check the coil secondary resistance by hooking one ohmmeter lead to a primary terminal and the other lead to the large center (high-tension) terminal. If the measured resistances are not as specified, the coil is likely defective and should be replaced. To install the coil, hook up the wires and attach the cable to the negative battery terminal. For a Direct Ignition System (DIS) coil pack on 3.3L and 3.8L engines, start by labeling the six spark plug wires and measuring the resistance of each cable. It should be 3 to 12 k-ohms per foot of cable, replacing any cable not within this range. Remove the four coil pack mounting bolts, lift up the coil pack, and unplug the electrical connector. Measure the resistance on the primary side of each coil with a digital ohmmeter, making sure the test lead probes have good contact with the terminals. Connect an ohmmeter between the B+ pin and the pin corresponding to the particular cylinder at the coil. Measure the secondary resistance of the coil between the paired high tension towers of each group of cylinders. If any coil in the coil pack fails either of the above tests, replace the coil pack. Installation is the reverse of removal.

If a coil is misfiring or not firing at all, or causing the PCM to set a DTC indicating a misfire, try swapping it with an adjacent coil. If the suspect coil was causing a DTC for one cylinder, it will likely set the same DTC when installed above another cylinder, indicating a defective coil. For V6 engines, removing the rear ignition coil on the left cylinder head requires removing the air intake duct or upper intake manifold. Disconnect the electrical connector from the coil, remove the mounting screw, and pull off the coil. Installation is the reverse. For V8 engines, remove the engine cover and disconnect the electrical connector and spark plug wire boot for the companion cylinder. Remove the coil mounting bolts and carefully pull up with a twisting motion to disengage the rubber spark plug boots. Inspect the condition of the rubber spark plug boot and replace if necessary. Installation is the reverse.

The first step is to dampen a cloth and use it to clean the coils.

Remove the engine cover and disconnect the electrical connector and spark plug wire boot for the companion cylinder. Remove the coil mounting bolts and carefully pull up with a twisting motion to disengage the rubber spark plug boots. Inspect the condition of the rubber spark plug boot and replace if necessary.

Remove the engine cover and disconnect the electrical connector and spark plug wire boot for the companion cylinder. Remove the coil mounting bolts and carefully pull up with a twisting motion to disengage the rubber spark plug boots. Inspect the condition of the rubber spark plug boot and replace if necessary.

To remove this coil, you need to remove the upper intake manifold.

Disconnect the electrical connector from the ignition coil and remove the bolt attaching the ignition coil to the valve cover. Grasp the ignition coil firmly and pull off the spark plug using a twisting motion.

It should be ensured that the coil fits securely onto the spark plug(s).

After inspecting the coils, you should make sure that each coil fits securely onto the spark plug(s).

Start by removing the ignition coil(s). Clean the outer case and check for any damage or cracks. Clean the coil primary terminals and remove any corrosion with a wire brush. Next, check the coil primary resistance by connecting the ohmmeter leads to the two primary coil terminals. Repeat this step for each coil. Then, check the coil secondary resistance by connecting one ohmmeter lead to a coil primary terminal and the other lead to the spark plug terminal. Repeat this step for each coil. Compare the measurements to the specified resistance values and replace the ignition coil(s) if necessary. To replace the coil, remove the air inlet duct/resonator if necessary. Disconnect the electrical connector and clean the area surrounding the ignition coil(s) with compressed air. Remove the nut from the ignition coil mounting stud and carefully pull the coil up with a twisting motion. Finally, remove the coil from the engine compartment and install the new coil in reverse order.

If damage is found on a coil, it should be replaced.