How to Replace the Engine Coolant Temperature Sensor on Chrysler 200?

Handle the Engine Coolant Temperature (ECT) sensor with care. Damage to the ECT sensor will affect the operation of the entire fuel injection system. 2011 and earlier 2.4L engines have two ECT sensors: Sensor 1 is located at the left end of the engine on the coolant adapter housing; Sensor 2 is located on the right front side of the engine block, above the oil pressure sensor. 2012 and later 2.4L models only have one ECT sensor, located at the left end of the engine on the coolant adapter housing. On 2.7L engines, the ECT sensor is located at the right end of the engine on the coolant outlet housing. On 3.5L engines, the ECT sensor is located at the left end of the engine, near the throttle body and EGR valve. On 3.6L engines, the ECT sensor is threaded into the left front end of the front-bank cylinder head. Disconnect the negative battery cable from the remote ground terminal or battery. Drain the engine coolant to a point lower than that of the sensor. Disconnect the electrical connector from the sensor, then unscrew the sensor. Before installing a threaded ECT sensor, wrap the threads of the sensor with Teflon tape to prevent coolant leakage. Installation is otherwise the reverse of removal. Tighten threaded ECT sensors to the torque. Refill the cooling system.

Genuine Chrysler 200 Coolant Temperature Sensor

Coolant Water Temperature Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

5 Coolant Temperature Sensors found

View related parts
Chrysler 200 Sensor-Fluid Temperature
Part Number: 68164627AA
$41.81 MSRP: $61.50
You Save: $19.69 (33%)
ADD TO CART
Product Specifications
- Other Name: Sensor Fluid Temperature
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2014-2017 Chrysler 200 | C AWD, C FWD, Limited, Limited Convertible, Limited Sedan, LX, LX Sedan, S AWD, S Convertible, S FWD, Touring Convertible, Touring Sedan | 6 Cyl 3.6L
View related parts
Chrysler 200 Sensor-COOLANT Temperature
Part Number: 5033313AA
$26.91 MSRP: $39.70
You Save: $12.79 (33%)
ADD TO CART
Product Specifications
- Other Name: Sensor Coolant Temperature; Coolant Temperature Sensor, Temperature Sensor
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2014 Chrysler 200 | Limited Sedan, LX Convertible, LX Sedan, Touring Convertible, Touring Sedan | 4 Cyl 2.4L
View related parts
Chrysler 200 Sensor-Temperature
Part Number: 68088241AA
$206.11 MSRP: $312.00
You Save: $105.89 (34%)
ADD TO CART
Product Specifications
- Other Name: Sensor Temperature; Oil Temperature Sending Unit
- Replaces: 68119586AA
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2015-2017 Chrysler 200 | C FWD, Limited, LX, S FWD | 4 Cyl 2.4L
View related parts
Chrysler 200 Sensor-Temperature
Part Number: 5033314AA
$23.44 MSRP: $34.60
You Save: $11.16 (33%)
ADD TO CART
Product Specifications
- Other Name: Sensor Temperature
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2014 Chrysler 200 | Limited Sedan, LX Convertible, LX Sedan, Touring Convertible, Touring Sedan | 4 Cyl 2.4L
View related parts
Chrysler 200 Sensor-Fluid Temperature
Part Number: 5149077AB
$44.07 MSRP: $65.85
You Save: $21.78 (34%)
ADD TO CART
Product Specifications
- Other Name: Sensor Fluid Temperature
- Replaces: 5149096AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2017 Chrysler 200 | C AWD, C FWD, Limited, Limited Convertible, Limited Sedan, LX, LX Sedan, S AWD, S Convertible, S FWD, S Sedan, Touring Convertible, Touring Sedan | 4 Cyl 2.4L, 6 Cyl 3.6L

Chrysler 200 Coolant Temperature Sensor

The Coolant Temperature Sensor used in Chrysler 200 vehicle is responsible for sensing the temperature of the coolant while the engine performance is critical. This sensor is important since it feeds the system with data required in managing the engine's effectiveness. Several types of Coolant Temperature Sensors have been used in the Chrysler 200 series in the past years, even though they are generally used with a similar purpose, it is not impossible to find a difference in the design or the type of technology involved. These variations could impact on how the sensor relays information on the existing temperature of the engine to that of the engine control unit and thereby minimize on the general performance of the vehicle.

Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Chrysler 200 Coolant Temperature Sensor at great affordable prices. Moreover, all genuine Chrysler 200 Coolant Temperature Sensor come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.

Chrysler 200 Coolant Temperature Sensor Parts Questions & Experts Answers

Sensor-COOLANT Temperature
5033313AA
Q: How to Replace the Engine Coolant Temperature Sensor on Chrysler 200?
A: Handle the Engine Coolant Temperature (ECT) sensor with care. Damage to the ECT sensor will affect the operation of the entire fuel injection system. 2011 and earlier 2.4L engines have two ECT sensors: Sensor 1 is located at the left end of the engine on the coolant adapter housing; Sensor 2 is located on the right front side of the engine block, above the oil pressure sensor. 2012 and later 2.4L models only have one ECT sensor, located at the left end of the engine on the coolant adapter housing. On 2.7L engines, the ECT sensor is located at the right end of the engine on the coolant outlet housing. On 3.5L engines, the ECT sensor is located at the left end of the engine, near the throttle body and EGR valve. On 3.6L engines, the ECT sensor is threaded into the left front end of the front-bank cylinder head. Disconnect the negative battery cable from the remote ground terminal or battery. Drain the engine coolant to a point lower than that of the sensor. Disconnect the electrical connector from the sensor, then unscrew the sensor. Before installing a threaded ECT sensor, wrap the threads of the sensor with Teflon tape to prevent coolant leakage. Installation is otherwise the reverse of removal. Tighten threaded ECT sensors to the torque. Refill the cooling system.