How do you disconnect and reinstall the ignition switch and key lock cylinder on Chrysler Town & Country?

Take off the cable from the negative terminal of the battery. Takeaway the knee bolster and the steering column covers, if any. Rotate the ignition lock cylinder to the ON position, press the ignition lock cylinder retaining tab, and take out the ignition lock cylinder. Lay in the upper and lower steering column covers. Switch on the ignition by turning the key and fit the ignition lock cylinder as well. Screw the cable on the negative terminal of the battery. Cautiously unscrew the one Torx sized head mounting screw used for the ignition switch. Push down the ignition switch retaining tabs and thus release the switch from the steering column. Pull the connector from the ignition switch releasing the connector tab; do not bend the connector. Prior to connecting the vessel to the ignition switch make sure that the ignition key is in ON position and the actuator shaft of the ignition lock cylinder housing is to ON. Another is when placing the ignition switch unto the actuator shaft the switch will go over the two retaining tabs. Be certain that the square receptacle in the ignition switch is in the ON position, line the receptacle and its actuator shaft before pushing the switch over the ignition lock cylinder housing until the tabs are locked. Fit in the upper and the lower steering column covers and then ground terminal of the battery to the cable connected to them.

Genuine Chrysler Town & Country Ignition Switch

Starter Ignition Switch

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

9 Ignition Switches found

View related parts
Chrysler Town & Country Switch-Ignition
Part Number: 4671324
$77.74 MSRP: $119.00
You Save: $41.26 (35%)
ADD TO CART
Product Specifications
- Other Name: Switch Ignition; Ignition Switch
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1999-2000 Chrysler Town & Country | LX AWD, LX FWD, LXi AWD, LXi FWD, Limited AWD, Limited FWD, SX | 6 Cyl 3.3L, 6 Cyl 3.8L
- 1997 Chrysler Town & Country | LX AWD, LX FWD, LXi AWD, LXi FWD, SX | 6 Cyl 3.3L, 6 Cyl 3.8L
View related parts
Chrysler Town & Country SWITCHPKG-Ignition
Part Number: 4797401
$4.50 MSRP: $189.00
You Save: $184.50 (98%)
ADD TO CART
Product Specifications
- Other Name: Switch, Ignition Starter
- Replaced by: 4797401AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1994-1995 Chrysler Town & Country | Base AWD, Base FWD | 6 Cyl 3.8L
View related parts
Chrysler Town & Country Switch-Ignition
Part Number: 4685719AB
$60.83 MSRP: $91.60
You Save: $30.77 (34%)
ADD TO CART
Product Specifications
- Other Name: Switch Ignition
- Replaced by: 4685719AI
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2001-2006 Chrysler Town & Country | Base, EL, EX, Limited AWD, Limited FWD, LX AWD, LX FWD, LXi AWD, LXi FWD, Touring AWD, Touring FWD | 6 Cyl 3.3L, 6 Cyl 3.5L, 6 Cyl 3.8L
View related parts
Chrysler Town & Country Switch-Ignition
Part Number: 4685719AE
$60.83 MSRP: $91.60
You Save: $30.77 (34%)
ADD TO CART
Product Specifications
- Other Name: Switch Ignition
- Replaced by: 4685719AI
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2007 Chrysler Town & Country
View related parts
Chrysler Town & Country Switch-Engine START/STOP
Part Number: 1FU931X9AC
$27.65 MSRP: $40.75
You Save: $13.10 (33%)
ADD TO CART
Product Specifications
- Other Name: Button Engine Start/Stop; Ignition Switch, Power Switch, Start Button
- Replaces: 1FU931X9AB
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 2011-2016 Chrysler Town & Country | Gold, Limited, Limited Platinum, LX, S, Touring, Touring L, Touring-L | 6 Cyl 3.6L
View related parts
Chrysler Town & Country Switch Ignition & Starter
Part Number: 3747529
Product Specifications
- Other Name: Switch, Ignition & Starter; Ignition Switch
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1984-1988 Chrysler Town & Country | 4 Cyl 2.2L, 4 Cyl 2.5L, 4 Cyl 2.6L
View related parts
Chrysler Town & Country Switch-Ign & Starter
Part Number: 3747882
Product Specifications
- Other Name: Switch, Ignition & Starter; Cylinder & Key, Ignition Switch
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1990 Chrysler Town & Country | 6 Cyl 3.0L, 6 Cyl 3.3L
- 1984-1988 Chrysler Town & Country | 4 Cyl 2.2L, 4 Cyl 2.5L, 4 Cyl 2.6L
View related parts
Chrysler Town & Country Ignition & Starter
Part Number: 4221201
Product Specifications
- Other Name: Switch, Ignition & Starter; Cylinder & Key, Ignition Switch
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1990 Chrysler Town & Country | 6 Cyl 3.0L, 6 Cyl 3.3L
- 1984-1988 Chrysler Town & Country | 4 Cyl 2.2L, 4 Cyl 2.5L, 4 Cyl 2.6L
View related parts
Chrysler Town & Country None-Ignition Lock Cylinder
Part Number: 5257137
Product Specifications
- Other Name: Driver, Ignition Cylinder, Push to Lock
- Warranty: This genuine part is guaranteed by Mopar's factory warranty.
Fits the following Vehicles:
- 1990-1995 Chrysler Town & Country | Base AWD, Base FWD | 6 Cyl 3.0L, 6 Cyl 3.3L, 6 Cyl 3.8L

Chrysler Town & Country Ignition Switch

The Ignition Switch is used in Chrysler Town & Country vehicles as a part of the ignition and charging circuit that energises the principal functions of the vehicle's electrical system. The main function of this kind of the start/stop switch is to turn on the vehicle's computer to give necessary power and allow the Chrysler Town & Country vehicle to start. In the past Chrysler Town & Country cars incorporated usage of regular metal keys for the ignition system that locked the system only with the right key. The latest car models use the so-called keyless technologies where the push buttons are installed still, they can work only with the help of the transponder signal. However, the advancement of the Ignition Switch is quite evolutionary in that it transits from having mechanical keys to the touchless keyless entry in the Chrysler Town & Country's series. In general therefore, the Ignition Switch is intended for easy replacement and follows a plug and play system whose design depends on the vehicle.

Looking for affordable and high-quality auto parts? Then you have already arrived at the proper online shop. We offer all Chrysler Town & Country Ignition Switch at great affordable prices. Moreover, all genuine Chrysler Town & Country Ignition Switch come with a manufacturer's warranty. In the long run, you would realize you have saved a lot of trouble and money with OEM parts from here.

Chrysler Town & Country Ignition Switch Parts Questions & Experts Answers

Switch-Ignition
4685719AB
Q: How do you disconnect and reinstall the ignition switch and key lock cylinder on Chrysler Town & Country?
A: Take off the cable from the negative terminal of the battery. Takeaway the knee bolster and the steering column covers, if any. Rotate the ignition lock cylinder to the ON position, press the ignition lock cylinder retaining tab, and take out the ignition lock cylinder. Lay in the upper and lower steering column covers. Switch on the ignition by turning the key and fit the ignition lock cylinder as well. Screw the cable on the negative terminal of the battery. Cautiously unscrew the one Torx sized head mounting screw used for the ignition switch. Push down the ignition switch retaining tabs and thus release the switch from the steering column. Pull the connector from the ignition switch releasing the connector tab; do not bend the connector. Prior to connecting the vessel to the ignition switch make sure that the ignition key is in ON position and the actuator shaft of the ignition lock cylinder housing is to ON. Another is when placing the ignition switch unto the actuator shaft the switch will go over the two retaining tabs. Be certain that the square receptacle in the ignition switch is in the ON position, line the receptacle and its actuator shaft before pushing the switch over the ignition lock cylinder housing until the tabs are locked. Fit in the upper and the lower steering column covers and then ground terminal of the battery to the cable connected to them.